Electro Industries/GaugeTech Shark 100T User manual

V.1.03
November 5, 2018

This page intentionally left blank.

Doc# E166705 V.1.03 QS - 1
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
7.62in
193.5mm
4.36in
80.6mm
3.18in
110.6mm
0.81in
20.5mm
Mechanical Installation
Recommended Tools for MP200 Unit Installation:
#2 Phillips screwdriver; 1/4-inch (0.25”) nut driver, socket, box, or open-end wrench; wire cutters.
NOTE: The MP200 unit is designed to withstand harsh environmental conditions; however it is recom-
mended you install it in a dry location, free from dirt and corrosive substances.
1. Mount the unit against any firm, flat surface.
2. Use a #8 screw in each of the four slots on the flange to ensure that the MP200 unit is installed
securely.
IMPORTANT!
For safety reasons, mount
the MP200 unit in an enclosed and
protected environment, such as in a
switchgear cabinet.
Connect an earth ground to the
post on the side of the MP200 unit,
using an AWG 12 wire.
Install a switch or circuit breaker
nearby; label it clearly as the
MP200 unit’s disconnecting
mechanism.
193.1mm
286.5mm
0.28in
0.80in
20.4mm
76.9mm
7.60in
11.28in
278.9mm
centered
3.03in
7.2mm
4.8mm
10.98in
0.19in
centered
4.50in
114.3mm 0.12in
2.9mm

Doc# E166705 V.1.03 QS - 2
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electrical Installation:
Service: Three Phase, 4-Wire WYE Service Direct Voltage and 3 CT Connection for Metering
8 Three Phase Loads: MP200-Y
IMPORTANT! All CTs must have one side grounded to reduce shock hazard.
EIG highly recommends using shorting blocks like the EI SB-6TC so that the meter can be removed
from service while the CT is energized. You can order the EI SB-6TC at www.electroind.com.
WARNINGS! For Electrical Installation:
All Primary and Secondary circuits can, at times, produce lethal voltages and currents.
Avoid contact with any current-carrying surfaces.
The current inputs are only to be connected to external current transfomers (CTs).
I1-LO
LOAD
V2 V1
LINE
N
I1-HI
V1
I3-HI
V3
V3
I2-HI
I2-LO
V2
N
I3-LO
SERVICES: WYE, 4 WIRE.
Power Supply
Connection
CT Shorting Block
EI# SB-6CT
Only one 3 phase circuit is shown.
Duplicate for additional circuits.
Earth Ground
Earth Ground
FUSES
3 x 0.1A
FUSE 3A
CONNECTION TYPE: Direct Voltage, CTs
3
2
1
N
L(+) N(-)

Doc# E166705 V.1.03 QS - 3
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Service: Three Phase, 4-Wire WYE Service with 3 PT Voltage and 3 CT Connection
for Metering 8 Three Phase Loads - MP200-Y
3
2
I1-LO
LOAD
V2 V1
LINE
N
1
L(+) N(-)
I1-HI
V1
I3-HI
V3
V3
I2-HI
I2-LO
N
V2
N
I3-LO
SERVICES: WYE, 4 WIRE.
Power Supply
Connection
CT Shorting Block
EI# SB-6CT
Only one 3 phase circuit is shown.
Duplicate for additional circuits.
Earth Ground
Earth Ground
FUSES
3 x 0.1A
FUSE 3A
Earth Ground
CONNECTION TYPE: 3PTs, CTs
IMPORTANT! All CTs must have one side grounded to reduce shock hazard.
EIG highly recommends using shorting blocks like the EI SB-6TC so that the meter can be removed
from service while the CT is energized. You can order the EI SB-6TC at www.electroind.com.

Doc# E166705 V.1.03 QS - 4
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Service: Three Phase, 3-Wire Delta Service with 2 CT Connection for Metering 8 Three Phase
Loads - MP200-Y
IMPORTANT! All CTs must have one side grounded to reduce shock hazard.
I1-LO
LOAD
V2 V1
LINE
I1-HI
V1
I3-HI
V3
V3
V2
I3-LO
SERVICES: DELTA, 3 WIRE.
Power Supply
Connection
CT Shorting Block
EI# SB-6CT
Only one 3 phase circuit is shown.
Duplicate for additional circuits.
Earth Ground
Earth Ground
Earth Ground
FUSES
2 x 0.1A
FUSE 3A
CONNECTION TYPE: NO PTs, 2 CTs
C
BA
L(+) N(-)
Not connected to meter

Doc# E166705 V.1.03 QS - 5
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Single Phase, 2-Wire Service with Direct Voltage and 3 CT Connection for Metering 24 Single
Phase Loads: MP200-S
IMPORTANT! All CTs must have one side grounded to reduce shock hazard.
EIG highly recommends using shorting blocks like the EI SB-6TC so that the meter can be removed
from service while the CT is energized. You can order the EI SB-6TC at www.electroind.com.
I1-LO
LOADS
VL
LINE
N
1
L(+) N(-)
I1-HI
VL
I3-HI
I2-HI
I2-LO
N
N
I3-LO
SERVICES: SINGLE PHASE, 2-WIRE
CONNECTION TYPE: Direct Voltage, CTs
Power Supply
Connection
Only three circuits are shown.
Duplicate for additional circuits.
Short Voltage inputs
together
Earth Ground
CT Shorting Block
EI# SB-6CT
Earth Ground
FUSE 3A

Doc# E166705 V.1.03 QS - 6
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Service: Single Phase, 3-Wire Service with Direct Voltage and 1 CT Connection for Metering
24 Single Phase Loads - MP200-S
IMPORTANT! All CTs must have one side grounded to reduce shock hazard.
EIG highly recommends using shorting blocks like the EI SB-6TC so that the meter can be removed
from service while the CT is energized. You can order the EI SB-6TC at www.electroind.com.
I1-LO
LOADS
VL1
LINE
N
L(+) N(-)
I1-HI
VL1
I3-HI
I2-HI
I2-LO
VL2
I3-LO
CONNECTION TYPE: Direct Voltage, CTs
To monitor 24 individual loads.
See accuracy table for limiting factors.
Power Supply
Only one circuit is shown.
Duplicate for additional circuits.
Short Voltage inputs
together
Earth Ground
CT Shorting Block
EI# SB-6CT
Earth Ground
FUSE 3A
VL2
VL1
VL2
21
N
FUSES
2 x 0.1A
Run lines VL1 and VL2 through
the CT in opposite directions
Set PT ratio to half
in the meter.
SERVICE: SINGLE PHASE, 3-WIRE
Connection

Doc# E166705 V.1.03 QS - 7
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
MP200 Metering System Configuration:
1.Connect to the MP200 unit through its
USB port: Use a USB Type A to B plug to
connect from your PC’s USB port to the
MP200 unit’s USB port. If your PC doesn’t
automatically find the USB driver, download
it from the product CD that came with the
MP200 unit (see Appendix A in the MP200
Metering System Installation and Operation
Manual on the CD).
NOTE: This Quickstart shows connection
using the USB port. For Ethernet/Wifi or
RS485 connection, see the MP200 Metering
System Installation and Operation Manual.
2. Open Communicator EXTTM software
(download from product CD).
3. Click Connect on the tool bar. You will see
the Connect screen, shown on the right. Make sure
the Address, Baud Rate, and Protocol settings match
the ones shown here.
4. Click Connect - the Device Status screen confirms the
connection; click OK to close it. The Communicator EXTTM
application’s Main screen opens.
5.Click the Profile button on the tool bar. The Device Profile
screen opens. The Tree menu on the left side of the
screen lets you choose setting screens.
6. Click System Settings to open one of the screens shown
below. Use this screen to name the MP200 unit (CPU) and to label the circuits (individual meters).
You must give the MP200 CPU an individual, unique name to properly download data.
USB Port
Note that you
can also set
Data Protection
on this screen,
and create or
change a pass-
word for reset-
ting and/or
configuration.

Doc# E166705 V.1.03 QS - 8
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
8. Click Communications (see instructions below).
9. Click CT, PT Ratios and System Hookup (see instructions below).
10.Click Time Settings (see instructions on the next
page.
Communications Settings:
COM 1: RS485/ Ethernet/WIFI (optional)
Address: 1-247; Baud Rate: 57600;
Protocol: Modbus RTU/Modbus ASCII;
Response Delay: 0-750ms; Parity: Odd, Even or
None
COM 2: USB port
NOTE: The USB port settings are fixed.
COM 3: RS485
Address: 1-247; Protocol: Modbus RTU/ASCII
Baud Rate: 9600, 19200, 38400, 57600
Response Delay: 0-750ms
NOTE: Click the (1)Default to Ethernet or
(2)Default to Display button to set either the
(1)Ethernet settings for COM1 or (2)Display set-
tings for COM3, to their default values.
CT, PT Ratios and System Hookup: Note that the
settings you see on the screen depend on your
MP200 unit’s circuit configuration. The top screen is
for an MP200 unit with the single phase circuit con-
figuration (MP200-S). The second screen is for an
MP200 unit with the three phase circuit configura-
tion (MP200-Y). The bottom screen is for an MP200
unit with the 2 CT Delta circuit configuration.

Doc# E166705 V.1.03 QS - 9
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
For PT settings, see the MP200 Metering System Installation and Operation manual, on the enclosed
CD. The CT settings are:
CT Ratios
CT Numerator (Primary): 1 - 65535
CT Denominator (Secondary): 5 or 1 Amp,
depending on the MP200 unit’s ordered option
(this field is display only).
Time Settings:
To enable U.S. Daylight Savings Time (DST),
check the box and select the beginning and ending
dates, using the pull-down menus. You can set the
month, week, day of the week, and hour for DST to
begin.
Note that the hour field uses a 24 hour clock.
Update Device:
11. When changes are complete, click the Update button to send a new profile to the MP200 unit.
12. Click Cancel to Exit the screen.

Doc# E166705 V.1.03 QS - 10
MP200TM Metering System Quickstart Guide
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
This page intentionally left blank.
NOTE: For further details and additional programming screens, refer to the Communicator EXTTM 3.0
Software User Manual on the enclosed CD (access the software manual by clicking Help>Contents
from the Communicator EXTTM application’s Title bar).
Communicator EXT™ is a trademark of Electro Industries/GaugeTech.