Electro Industries/GaugeTech Shark 100S User manual

Doc# E145723 V.1.16 QS - 1
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
Shark® 100S/200S Meter Quickstart Guide
CAUTION! Installation of the Shark® 100S/200S meter must be performed only by qualified personnel
who follow standard safety precautions during all procedures. Those personnel should have appropriate
training and experience with high voltage devices. Appropriate safety gloves, safety glasses and protec-
tive clothing are recommended.
During normal operation of the Shark® meter, dangerous voltages flow through many parts of the unit, includ-
ing: Terminals and any connected CTs (Current Transformers) and PTs (Potential Transformers), all I/O Modules
and their circuits. All Primary and Secondary circuits can, at times, produce lethal voltages and currents. Avoid
contact with any current-carrying surfaces.
Do not use the meter or any I/O device for primary protection or in an energy-limiting capacity. The meter can
only be used as secondary protection.
IMPORTANT! Refer to your meter’s Installation and Operation Manual for additional safety warnings before
performing installation, wiring, or maintenance of your meter. See the link to the manual, below.
NOTE: This Quickstart Guide gives basic installation, wiring, and programming instructions.For additional meter
operation and programming information, refer to your meter’s Installation and Operation Manual and the Communi-
cator PQATM, MeterManagerPQATM, and EnergyPQA.comTM Software User Manual on EIG’s website:
User Manual:
Shark® 100S Meter
https://www.electroind.com/products/shark-100s-economical-wifi-submeter/
Shark® 200S Meter
https://www.electroind.com/products/shark-200s-advanced-data-logging-wifi-submeter/
From the webpage, click Technical Documents>User Manual.
Software Manual:
https://www.electroind.com/products/communicatorpqa-software-application-5/
From the webpage, click Technical Documents>User Manual.
CommunicatorPQATM Setup Software:
https://www.electroind.com/products/communicatorpqa-software-application-5/
From the webpage, click Download ComPQA Pro. To get a Professional license for the software, email sales@elec-
troind.com or call 516-334-0870.
All EIG’s metering and software products’ literature can be accessed from:
https://www.electroind.com/all-products/
For software and metering integration, EIG’s Technical Support Engineers are available on an hourly or daily basis to
help with typical commissioning assistance, which includes:
• Verifying meter installation and wiring.
• Verifying proper system integration.
• Working with 3rd parties to ensure cross compatibility.
• Advising users on best practices for optimal implementation.
You can reach Technical Support from 8 a.m. to 8 p.m. EST, Monday-Friday, at 516-334-0870.

Doc# E145723 V.1.16 QS - 2
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
Earth Ground
L(+)
Power
Supply
Connection
N(-)
GND
L1
Vref
Vc
Vb
Va
LINE
CT
Shorting
Block
L2
FUSES
3 x 0.1A
FUSE
3A
CN2
CN1
Ia+ Ia- Ib+ Ib- Ic+ Ic-
Va Vb Vc Vref L1 L2 PE
Electronic Circuits
LOAD
A
A
B
B
C
C
N
N
Earth Ground
L(+)
Power
Supply
Connection
N(-)
GND
L1
Vref
Vc
Vb
Va
LINE
CT
Shorting
Block
L2
FUSES
3 x 0.1A
FUSE
3A
CN2
CN1
Ia+ Ia- Ib+ Ib- Ic+ Ic-
Va Vb Vc Vref L1 L2 PE
Electronic Circuits
LOAD
A
A
B
B
C
C
N
N
Earth Ground
WYE with PTs, 3
Phase, 4 Wire
Location of JP2
Enlargement of JP2,
Showing Settings
Detail of JP2 Board and
LAN/485 Setting
WYE Direct, 3
Phase, 4 Wire
Front Cover
Support fitted
into its base
Power Supply
Inputs (Inputs
are unipolar)
Electronic Circuits
Ethernet, RJ45
Jack
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Va Vb Vc Vn L1 L2 PE
RS485
KYZ Pulse
Output
Wireless Ethernet Connection
RS485 Output
(Do not put the
Voltage on these
terminals!)
Voltage
Inputs
Current
Inputs
Access Holes for
Wiring
JP2
WARNING! During normal operation of the meter
dangerous voltages flow through many parts of the meter,
including Terminals and any connected CTs and PTs, all I/O
modules and their circuits. All Primary and Secondary
circuits can, at times, produce lethal voltages and currents. Avoid
contact with any current-carrying surfaces. Before performing ANY
work on the Shark® 100S/200S meter, make sure the meter is
powered down and ALL circuits are de-energized.
AVERTISSEMENT! Pendant le fonctionnement normal du compteur
Shark® 100S/200S des tensions dangereuses suivant de nombreuses
pièces, notamment, les bornes et tous les transformateurs de courant
branchés, les transformateurs de tension, toutes les sorties, les entrées
et leurs circuits. Tous les circuits secondaires et primaires peuvent
parfois produire des tensions de létal et des courants. Évitez le contact
avec les surfaces sous tensions. Avant de faire un travail dans le
compteur, assurez-vous d'éteindre l'alimentation et de mettre
tous les circuits branchés hors tension.
Select wiring diagram to meet your application. See User Manual for additional wiring diagrams.
NOTE: Jumper 2 (JP2) must be set for
either RS485 or Ethernet communica-
tion (see figures on the left for location
of JP2 and settings). Put the jumper on
positions 2 and 3 for LAN (Ethernet)
communication, or on 1 and 2 for
RS485 communication.
IMPORTANT! All wiring is done with the cover open, as shown above. The front cover support fits into its base.
Make sure the support is up before closing the front cover.

Doc# E145723 V.1.16 QS - 3
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
Program Settings Using the Faceplate Buttons: (MENU, ENTER, DOWN ARROW, RIGHT
ARROW) See the figure below for the location of the faceplate buttons.
Access Configuration Mode:
1.Push the MENU button - you will see the display on the right; rSt will be
blinking.
2.Press the DOWN ARROW once. CFG (Configuration) moves to the
top of the display.
3.Press the ENTER button. You will see the Configuration menu, shown
on the right.
MAX
MIN
VOLTS L-N
AMPS
%LOAD
120%-
PRG
%THD
LM2
LM1
90%-
60%-
30%-
VOLTS L-N
W/VAR/PF
VA/H z
Wh
KILO
VARh
VAh
Wh Pulse
MEGA
A
B
C
MENU ENTER
IrDA 0000
0.659
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
Earth Ground
L(+)
Power
Supply
Connection
N(-)
GND
L1
Vc
Vb
Va
LINE
CT
Shorting
Block
L2
FUSES
2 x 0.1A
FUSE
3A
CN2
CN1
Ia+ Ia- Ib+ Ib- Ic+ Ic-
Va Vb Vc Vref L1 L2 PE
Electronic Circuits
LOAD
A
A
B
B
C
C
Earth Ground
DELTA with PTs, 3
Phase, 3 Wire
Earth Ground
L(+)
Power
Supply
Connection
N(-)
GND
L1
Vc
Vb
Va
LINE
CT
Shorting
Block
L2
FUSES
3 x 0.1A
FUSE
3A
CN2
CN1
Ia+ Ia- Ib+ Ib- Ic+ Ic-
Va Vb Vc Vref L1 L2 PE
Electronic Circuits
LOAD
A
A
B
B
C
C
DELTA Direct, 3
Phase, 3 Wire

Doc# E145723 V.1.16 QS - 4
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
4.Press the DOWN ARROW and then press the ENTER button. You will see the CT
numerator setting screen (Ct-n). The current CT numerator is shown in the second
line. To change the setting, press the DOWN ARROW until the value you want is
displayed. Then press the RIGHT ARROW to move to the next digit. Repeat until
the setting is done.
5.Press the ENTER button to go to the CT denominator screen (CT-d). This setting is
display only - it can’t be changed.
6.Press the ENTER button to go to the CT Scaling setting screen (CT-S). The current
Scaling is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 1, 10, or 100.
7.Press the ENTER button to go to the PT numerator setting screen (Pt-n).The current
PT numerator is shown in the second line. To change the setting, press the DOWN
ARROW until the value you want is displayed. Then press the RIGHT ARROW to
move to the next digit. Repeat until the setting is done.
8.Press the ENTER button to go to the PT-denominator screen (Pt-d). The current
PT denominator is shown in the second line. To change the setting, press the DOWN
ARROW until the value you want is displayed. Then press the RIGHT ARROW to
move to the next digit. Repeat until the setting is done.
9.Press the ENTER button to go to the PT Scaling setting screen (PT-S). The current
Scaling is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 1, 10, 100, or 1000.
NOTE: See example CT and PT Settings on the next page.
10.Press the ENTER button to go to the Connection setting screen (Cnct). The current
setting is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 3 EL (element) WYE, 2 Ct del (Delta), or 2.5 EL WYE.
11.Press the ENTER button to go to the meter Address setting screen (Adr). The
meter’s current address is shown in the second line. To change the setting, press
the DOWN ARROW until the value you want is displayed. Then press the RIGHT
ARROW to move to the next digit. Repeat until the setting is done. Valid address-
es are from 001 through 247. If you are using the Ethernet option, do NOT
change anything on this screen.
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER

Doc# E145723 V.1.16 QS - 5
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
12.Press the ENTER button to go to the meter Baud Rate setting screen (bAUd). The
meter’s current Baud Rate is shown in the second line. Press the DOWN ARROW
to choose another Baud Rate. You can choose 9600 (choose this for RS485
connection), 19.2 (19200), 38.4 (38400) or 57.6 (57600). If you are using the
Ethernet option, do NOT change anything on this screen.
13.Press the ENTER button to go to the meter Protocol setting screen (Prot). The
meter’s current Protocol is shown in the second and third lines. Press the DOWN
ARROW to choose another communication Protocol. You can choose Mod rtU
(Modbus RTU; choose this for RS485 connection), Mod ASCI (Modbus ASCII), or
dnp (DNP 3.0). If you are using the Ethernet option, do NOT change
anything on this screen.
14.Press the ENTER button to go to the Scroll setting screen (SCrL). The current
setting is shown in the second line. Press the DOWN ARROW to choose another
setting. You can choose YES (the meter readings will scroll on the display) or no
(the meter readings will not scroll on the display).
15.Press the MENU button twice. You will see the Store Settings screen (Stor ALL?)
The default setting is YES. To save the settings you’ve made, press the ENTER
button. You will see the confirmation screen (Stor ALL done) and then the meter
resets.
NOTE: If you do not want to save your settings, press the RIGHT ARROW. YES
changes to no. Press the ENTER button.
Example CT Settings:
200/5 Amps: set the Ct-n value as 200, Ct-S value as 1.
800/5Amps: set the Ct-n value as 800, Ct-S value as 1.
2000/5 Amps: set the Ct-n value as 2000, Ct-S value as 1
10,000/5 Amps: set the Ct-n value as 1000, Ct-S value as 10.
Example PT Settings:
14400/120 Volts: set the Pt-n value as 1440, Pt-d value as 120, Pt-S value as 10.
138000/69 Volts: set the Pt-n value as 1380, Pt-d value as 69, Pt-S value as 100.
345000/115 Volts: set the Pt-n value as 3450, Pt-d value as 115, Pt-S value as 100.
345000/69 Volts: set the Pt-n value as 345, Pt-d value as 69, Pt-S value as 1000.
For additional programming instructions for the faceplate buttons, see Chapter 7 in your meter’s User
Manual (see page QS-1).
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER

Doc# E145723 V.1.16 QS - 6
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
Follow these steps to connect to the meter via the IrDA port:
1. Connect the meter to the PC. EIG offers a USB to IrDA cable, which can be ordered from EIG’s
website: https://www.electroind.com/products/usb-to-irda-adapter/.
2. Open CommunicatorPQATM software (see page QS-1 for the download link).
3. Click Connect in the Icon
Bar.
4. You will see the Connect screen. Make sure
your settings match the ones shown on the right
(use pull-down menus).
5. Click Connect. The Device Status screen opens,
confirming the connection. Click OK to close the
Device Status screen.
6. Click the Profile icon in the Icon bar.
7.The Device Profile screen opens. For the 100S, the tabs on the top of the screen let you choose
setting screens. For the 200S, there is a Tree menu on the left side of the screen.
Shark® 100S Meter Shark® 200S Meter
Click a tab to access the setting screen.
Click on a plus sign to see the
settings and click on a setting to
open that settings screen.

Doc# E145723 V.1.16 QS - 7
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
NOTE: The screens shown here are from the Shark® 100S meter. Some of the Shark® 200S meter’s
screens have additional settings. See Chapter 8 in the software user manual for details.
Program CT, PT Ratios
1. This is the first Device Profile
screen. To return to this screen
from another settings screen,
click the Scaling tab.
2. These are the settings:
a. CT Numerator (enter value you
want), Denominator (display
only), Multiplier (1, 10, or
100), CT Fullscale (Calculated
automatically)
b. PT Numerator (enter value you
want), Denominator (enter
value you want), Multiplier (1,
10, 100, or 1000), PT Fullscale (Calculated automatically)
NOTE: Voltage Full Scale = PT Numerator x PT Multiplier
Current Full Scale = CT Numerator x CT Multiplier
IMPORTANT! Specify Primary and Secondary Voltage in Full Scale (NOT Ratios).
NOTE: You can also enter the Ratios for CT/PT Numerator and Denominator and click the Update CT/
Update PT buttons to let the software calculate the Numerator, Denominator, and Multiplier for you.
You can then empty the Ratio fields and click the Update Ratio buttons to confirm the calculated set-
tings: you will see the same ratios you initially entered.
See Chapter 8 (200S) or Chapter 9 (100S) in the software manual for additional screen settings
instructions (see page QS-1; alternatively, you can click Help>Contents from the CommunicatorPQATM
software’s Main screen).
Program Communications:
1. Click the Communication tab.
2. The settings shown on the screen are the
default settings for the meter’s IrDA (COM1
and RS485 (COM2) ports. You can change the
settings, if necessary for your application. To
revert to the default RS485 port settings, click
Set COM2 to default (the 200S meter does not
have this option).
NOTE: If you do not have the RS485 option,
you can ignore those settings.

Doc# E145723 V.1.16 QS - 8
Shark® 100S/200S Quickstart
Electro Industries/GaugeTech
™
Powered by Innovation™
Program Meter Time: The meter is preset to Eastern time. To change the meter time:
1. From the Main screen’s Title bar, click Tools>Set Device Time.
2. You can either enter the time in the Time fields, or click Use
PC Time to set the time using your PC’s time.
3. Click Send.
Program Meter Name:
To enter a name/ID for the meter:
1. From the Device Profile screen, click
the Settings tab.
2. Input a new meter designation into the
Device/Meter Designation field. Note
that it is important to name each meter
individually, since the meter name is
used to name the log databases when
logs are downloaded.
See Chapter 8 (200S) or Chapter 9
(100S) in the software manual for an explanation of the other settings in this screen.
IMPORTANT! When you have made
changes to the meter’s Device Profile, click
Load Profile at the bottom of the Device Pro-
file screen to send the new settings to the
meter. The meter will reboot and then you can reconnect to it. Note that you can also click Save Profile
to save your changes without sending them to the meter.
Shark® is a registered trademark of Electro Industries/GaugeTech. CommunicatorPQATM, MeterManagerPQATM, and Ener-
gyPQA.comTM are trademarks of Electro Industries/GaugeTech.
https://electroind.com/