Electro Industries/GaugeTech Shark 100T User manual

Doc# E145704 QS - 1
Shark® 100T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Shark® 100T Quickstart Guide
Mechanical Installation
Installation Steps: Slide top of groove of meter onto DIN Rail. Press gently until the meter clicks into
place. If mounting with DIN Rail provided, use Black Rubber Stoppers (also provided) shown above.
To remove meter, pull down on Release clip.
Electrical Wiring: Select diagram to meet your application.
NOTE: Other wiring configurations are available. See the full Manual on the enclosed CD.
v
;CM=
v
CM
Ic Ib Ia
HI HI HI
LOLOLO
v
CM
v
CM
CM

CM

v
CM
DIN Installation
Release clip
100T
Dimensions
DIN Rail with black
rubber stoppers
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
N
N
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
N
N
C
C
B
B
A
A
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
WYE direct, 3
phase, 4 wire WYE with PTs, 3
phase, 4 wire
Delta direct, 3
phase, 3 wire Delta with PTs, 3
phase, 3 wire
High
Side
Low
Side

Doc# E145704 QS - 2
Shark® 100T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Program the Shark®100T Using RS485
Communication Wiring: The Shark®100T meter’s RS485 port
uses standard 2-wire, Half Duplex Architecture.
Factory Initial Default Settings: When the Shark 100T is powered
up, for 10 seconds you can connect to the meter using the Factory
Default Settings (even if the Device Profile has been changed). After
10 seconds the Device Profile reverts to the actual Device Profile in
use. This is one way you can always connect to the meter. The
Factory Initial Default Settings are:
Device Address:1
Baud Rate:9600
Protocol:Modbus RTU
Connection Steps:
1.Open Communicator EXT software.
2.Click Connect on the tool bar. The Connect
screen appears. Make sure your settings match
these (use pull-down windows). Click Connect.
Device Status screen confirms the connection.
3.Click OK. The main screen of Communicator
EXT appears.
Configuration Steps:
4.Click the Profile button on the tool bar. A set of program-
ming screens appears.
5.Click the Communications tab and select settings based
on your application.
6.Click the Scaling tab and select settings based on your
application.
Communications Settings:
COM2 (RS485):
Address (1-247)
Protocol (Modbus RTU, ASCII or DNP)
Baud Rate (9600 to 57600)
Response Delay (0-750 msec)
Scaling (CT, PT Ratios and System Wiring)
CT Numerator, Denominator, Multiplier, CT Fullscale (Calculated automatically)
PT Numerator, Denominator, Multiplier, PT Fullscale (Calculated automatically)
System Wiring: Use pull-down menu to select
Number of Phases: One, Two or Three

Doc# E145704 QS - 3
Shark® 100T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
NOTE: Voltage Full Scale = PT Numerator x PT Multiplier
Current Full Scale = CT Numerator x CT Multiplier
WARNING:Specify Primary and Secondary Voltage in Full
Scale (NOT Ratios).
Example CT Settings:
200/5 Amps:Set Ct-n value for 200, Ct-S value for 1.
800/5 Amps:Set Ct-n value for 800, Ct-S value for 1.
2,000/5 Amps:Set Ct-n value for 2000, Ct-S value for 1.
10,000/5 Amps:Set Ct-n value for 1000, Ct-S value for 10.
Example PT Settings:
14,400/120 Volts:Pt-n value is 1440, Pt-d value is 120, Pt-S
value is 10.
138,000/69 Volts:Pt-n value is 1380, Pt-d value is 69, Pt-S
value is 100.
345,000/115 Volts:Pt-n value is 3450, Pt-d value is 115, Pt-S value is 100.
345,000/69 VoltsPt-n value is 345, Pt-d value is 69, Pt-S value is 1000.
Update Device:
7.When changes are complete, click the Update button to send a new profile to the Shark 100T meter.
8.Click Cancel to Exit the profile (or) click other tabs to update other screens.
9.Use Communicator EXT to communicate with the device and perform required tasks.
NOTE: For further details and additional programming screens (Password, Limits, Energy and Dis-
play), refer to the Shark User’s Manual & Communicator EXT 3.0 Software Manual on the enclosed CD.
Program the Shark 100T Using Ethernet (INP10 Option)
Communication Wiring: The Shark 100T meter with Ethernet
has an RJ45 port on the meter back. Use an Ethernet cable to
connect the meter to your PC.
Factory Default Settings: The Factory Default IP parameters
programmed in the INP10 card are:
IP Address: 10.0.0.1
Subnet Mask: 255.255.255.0
Set up the PC’s Ethernet Adapter: The PC's Ethernet Adapter
must be set up for point-to-point communication.
1.Select Start>Control Panel>Network Connections. Right-click on the Local Area Connection you
will use to communicate with the meter and select Properties.
2.Select Internet Protocol [TCP/IP] and click the Properties button.
3.Click Use the Following IP Address radio button and enter: IP Address:10.0.0.2; Subnet Mask:
255.255.255.0.
4.Click the OK button.
Connect
Ethernet
cable
here

Doc# E145704 QS - 4
Shark® 100T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Set up the Ethernet Card (INP10 Option): Establish a Telnet connection on port 9999.
(NOTE: Windows 7 users must enable Telnet Client. Select Control Panel>Programs and Features>
Turn windows features on or off. Check the Telnet Client box and click OK. Telnet Client is now active.)
1. From the Windows Start menu, click Run and type 'cmd'.
2. Click the OK button to bring up the Windows' Command Prompt window. In the Command Prompt
window, type: “telnet 10.0.0.1 9999" and press the Enter key.
NOTE: Make sure there is a space between the IP address and 9999.
3. When the Telnet connec-
tion is established you will
see a message similar to
the example shown on the right.
4. To proceed to Setup Mode press Enter again.
You will see a screen similar to the one
shown on the right.
5. Change ONLY the parameters in group 1. To
do so, type number "1."
6. Once group 1 is selected, the individual
parameters display for editing. Either: Enter
a new parameter if a change is required, OR
press Enter to proceed to the next parame-
ter without changing the current setting.
IMPORTANT! Settings 2, 3, and 4 must have the default values shown here.
Example: Setting device with static IP Address.
IP Address <010> 192.<000> 168.<000> .<000> .<001>
Set Gateway IP Address <N>? Y
Gateway IP Address: <192> .<168> .<000> .<001>
Set Netmask <N for default> <Y>? Y
7. Continue setting up parameters as needed. After you finish your modifications, press the "S" key on
the keyboard. This saves the new values and causes a Reset in the Ethernet card.
CAUTION! DO NOT PRESS 'D' as it will overwrite any changes and save the default values.
Connection Steps:
1.Open Communicator EXT software.
2.Click Connect on the tool bar. You will see
the Connect screen shown on the right. The
setting shown here is the default setting.
3.Click Connect. The Device Status screen
confirms the connection.
4.Click OK. Communicator EXT’s Main screen
opens. Follow the instructions on page Q-2.
1) Network/IP Settings:
IP Address ...............….. 10.0.0.1
Default Gateway .............--- not set ---
Netmask .....................…255.255.255.0
2) Serial & Mode Settings:
Protocol ...................... Modbus/RTU,Slave(s) attached
Serial Interface ........... 57600,8,N,1,RS232,CH1
3) Modem/Configurable Pin Settings:
CP1…………..Not Used
CP2…………..Not Used
CP3…………..Not Used
4) Advanced Modbus Protocol settings:
Slave Addr/Unit Id Source .. Modbus/TCP header
Modbus Serial Broadcasts ... Disabled (Id=0 auto-mapped to 1)
MB/TCP Exception Codes ..... Yes (return 00AH and 00BH)
Char, Message Timeout ...... 00050msec, 05000msec
D)efault settings, S)ave, Q)uit without save
Select Command or parameter set (1..4) to change:
Serial Number 5415404 MAC Address 00:20:4A:54:3C:2C
Software Version V01.2 (000719)
Press Enter to go into Setup Mode
120811 V.1.07