Electrolux EW9W249W User manual

EW9W249W
EN Washer Dryer User Manual

CONTENTS
1. SAFETY INFORMATION....................................................................................3
2. SAFETY INSTRUCTIONS..................................................................................6
3. INSTALLATION.................................................................................................. 7
4. PRODUCT DESCRIPTION.............................................................................. 12
5. CONTROL PANEL........................................................................................... 13
6. DIAL AND BUTTONS....................................................................................... 15
7. PROGRAMMES............................................................................................... 17
8. BEFORE FIRST USE....................................................................................... 23
9. SETTINGS........................................................................................................23
10. DAILY USE..................................................................................................... 24
11. DAILY USE - WASHING & DRYING.............................................................. 29
12. DAILY USE - DRYING ONLY......................................................................... 31
13. FLUFF IN THE FABRICS............................................................................... 32
14. HINTS AND TIPS........................................................................................... 32
15. CARE AND CLEANING..................................................................................35
16. TROUBLESHOOTING....................................................................................41
17. CONSUMPTION VALUES..............................................................................46
18. TECHNICAL DATA.........................................................................................47
19. ACCESSORIES..............................................................................................47
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that
brings with it decades of professional experience and innovation. Ingenious and
stylish, it has been designed with you in mind. So whenever you use it, you can
be safe in the knowledge that you’ll get great results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com/webselfservice
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
www.electrolux.com2

Subject to change without notice.
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result
of incorrect installation or usage. Always keep the
instructions in a safe and accessible location for future
reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent
disability.
•This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
•Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
•Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
•Do not let children play with the appliance.
•Keep all packaging away from children and dispose of
it appropriately.
•Keep detergents away from children.
•Keep children and pets away from the appliance when
the door is open.
•If the appliance has a child safety device, it should be
activated.
•Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
ENGLISH 3

1.2 General Safety
•Do not change the specification of this appliance.
•This appliance is intended to be used in household
and similar applications such as:
–staff kitchen areas in shops, offices and other
working environments;
–by clients in hotels, motels, bed & breakfast and
other residential type environments;
–areas for communal use in blocks of flats or in
launderettes.
•The appliance shall be installed as a freestanding
product or below the kitchen worktop if space margins
permit.
•Do not install the appliance behind a lockable door, a
sliding door or a door with a hinge on the opposite
side, that would prevent the appliance door from being
fully open.
•Connect the mains plug to the mains socket only at
the end of the installation process. Make sure that the
mains plug is accessible after installation.
•The ventilation opening in the base must not be
covered by a carpet, mat, or any floor covering.
•CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
•Ensure good air ventilation in the room where the
appliance is installed to avoid the backflow of
unwanted gases into the room from appliances
burning gas or other fuels, including open fires.
•Exhaust air must not be discharged into a flue which is
used for exhausting fumes from any appliances
burning gas or other fuels.
•The operating water pressure at the water entry point
from the outlet connection must be between 0.5 bar
(0.05 MPa) and 8 bar (0.8 MPa).
www.electrolux.com4

•Do not exceed the maximum load of 9 kg (refer to the
"Programme chart" chapter).
•The appliance must be connected to the water mains
using the new supplied hose sets, or other new hose
sets supplied by the Authorised Service Centre.
•Old hose sets must not be reused.
•If the mains power supply cable is damaged, it must
be replaced by the manufacturer, its Authorised
Service Centre or similarly qualified persons to avoid
an electrical hazard.
•Wipe away lint or packaging debris that has
accumulated around the appliance.
•Do not run the appliance without filters. Clean the lint
filter before or after each use.
•Items that have been soiled with substances such as
vegetable or mineral oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and wax
removers should be washed separately with an extra
amount of detergent before being dried in the washer
dryer.
•Do not use the appliance if items have been soiled
with industrial chemicals.
•Do not dry unwashed items in the wash dryer.
•Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and
clothes, or pillows fitted with foam rubber pads should
not be dried in the washer dryer.
•Fabric softeners, or similar products, should only be
used as specified by the product manufacturer’s
instructions.
•Remove all objects from items that could be a source
of fire ignition such as lighters or matches.
•Never stop the washer dryer before the end of the
drying cycle unless all items are quickly removed and
separated so that residual heat can dissipate.
•The final part of the washer dryer cycle takes place
without heat (cool down cycle) to ensure that items
ENGLISH 5

reach a temperature that will not cause damage to
them.
•Do not use high pressure water sprays and/or steam
to clean the appliance.
•Clean the appliance with a moist cloth. Use only
neutral detergents. Do not use abrasive products,
abrasive cleaning pads, solvents or metal objects.
•Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
2. SAFETY INSTRUCTIONS
2.1 Installation
The installation must comply
with relevant national
regulations.
• Follow the installation instructions
supplied with the appliance.
• Do not install or use the appliance
where the temperature can be less
than 5°C or higher than 35 °C.
• Always keep the appliance vertical
when it is being moved.
• To make sure the compressor works
properly, wait 6 hours after the
installation before using the
appliance.
• Make sure that there is air circulation
between the appliance and the floor.
• Remove all the packaging and the
transit bolts.
• The floor area on which the appliance
is to be installed must be flat, stable,
heat resistant and clean.
• Keep the transit bolts in a safe place.
If the appliance is to be moved in the
future they must be reattached to lock
the drum to prevent an internal
damage.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use a damaged
appliance.
• Do not install the appliance where the
appliance door cannot be fully
opened.
• Adjust the feet to have the necessary
space between the appliance and the
flooring.
• When the appliance is in its
permanent position, check if it is
levelled correctly with the aid of a
spirit level. If it is not, adjust the feet
accordingly.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
2.3 Water Connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes, pipes
not used for a long time, where repair
work has been carried out or new
devices fitted (water meters, etc.), let
the water flow until it is clean and
clear.
www.electrolux.com6

• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
2.4 Use
WARNING!
Risk of injury, electric shock,
fire, burns or damage to the
appliance.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Do not touch the glass door while a
programme operates. The glass can
get hot.
• Do not dry damaged (torn, frayed)
items that contain padding or fillings.
• If laundry has been washed with a
stain remover, carry out an additional
rinse cycle before starting a drying
cycle.
• Make sure that all metal objects are
removed from the laundry.
• Dry only fabrics that are suitable to
dry in the appliance. Follow the
cleaning instruction on the item label.
• Do not sit or stand on the open door
of the appliance.
• Do not dry dripping wet clothes in the
appliance.
• Do not let hot items to touch the
plastic parts of the appliance.
• Remove a detergent ball (if used)
before starting a drying programme.
• Do not use a detergent ball if setting a
non-stop programme.
2.5 Compressor
WARNING!
Risk of damage to the
appliance.
• The compressor and its system in the
washer-dryer is filled with the special
agent which is free from fluoro-
chlorohydrocarbons. This system
must stay tight. The damage of the
system can cause a leakage.
2.6 Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
2.7 Disposal
• Disconnect the appliance from the
mains electrical and water supplies.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Remove the door catch to prevent
children or pets from becoming
trapped in the drum.
• Dispose of the appliance in
accordance with local requirements
for the disposal of Waste Electrical
and Electronic Equipment (WEEE).
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Unpacking
WARNING!
Remove all the packaging
and the transit bolts before
installing the appliance.
WARNING!
As you will put down the
appliance on the rear side,
wait about 6 hours before
you use it. This time is
necessary to enable the
compressor to work
properly.
WARNING!
Use the gloves.
1. Remove the external film. If
necessary, use a cutter.
ENGLISH 7

2. Remove the cardboard top and the
polystyrene packaging materials.
3. Remove the internal film.
4. Open the door and remove the
polystyrene piece from the door seal
and all the items from the drum.
5. Carefully put the appliance down on
its rear side.
6. Put the front polystyrene packaging
element on the floor under the
appliance.
Make sure not to
damage the hoses.
7. Remove the polystyrene protection
from the bottom.
1
2
8. Pull up the appliance in vertical
position.
9. Remove the power supply cable and
the drain hose from the hose holders.
It is possible to see
water flowing from the
drain hose. This is due
to the testing with water
of the appliance in
factory.
www.electrolux.com8

10. Remove the three bolts.
11. Pull out the plastic spacers.
12. Put the plastic caps, that you find in
the user manual bag, in the holes.
We recommend that you
keep the packaging and the
transit bolts for any
movement of the appliance.
3.2 Installation under a counter
630 mm
600 mm
≥ 870 mm
The appliance can be installed as
freestanding or below the kitchen counter with
correct space (see picture).
CAUTION!
Do not install the appliance
inside a sealed hollow!
Make sure that there is air
circulation throw the bottom of
the furniture.
CAUTION!
To assure free air circulation
under the appliance, do not
attach the sound barriers (if
available).
3.3 Positioning and levelling
1. Install the appliance on a flat hard
floor.
Make sure that carpets do
not stop the air circulation
below the appliance.
Make sure that the appliance
does not touch the wall or
other units.
2. Loosen or tighten the feet to adjust
the level.
WARNING!
Do not put cardboard, wood
or equivalent materials
below the appliance feet to
adjust the level.
ENGLISH 9

x4
The appliance must be level and stable.
A correct adjustment of the
appliance level prevents the
vibration, noise and the
movement of the appliance
when in operation.
When the machine is
installed on a plinth or if a
washer dryer is stacked on
the washing machine, use
the accessories described in
chapter 'Accessories'. Read
carefully the instructions
supplied with the appliance
and with the accessory.
3.4 The inlet hose
1. Connect the water inlet hose to the
back of the appliance.
2. Position it toward left or right
depending on the position of the
water tap.
20º20º
45º45º
Make sure that the inlet hose
is not in vertical position.
3. If necessary, loose the ring nut to set
it in the correct position.
4. Connect the water inlet hose to the
cold water tap with 3/4" thread.
CAUTION!
Make sure that there are no
leaks from the couplings.
Do not use an extension
hose if the inlet hose is too
short. Contact the service
centre for the replacement of
the inlet hose.
3.5 Water-stop device
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing.
The red sector in the window «A» shows
this fault.
www.electrolux.com10

A
If this occurs, close the water tap and
contact the authorized service centre to
replace the hose.
3.6 Water drainage
The drain hose should be positioned at a
height of not less than 60 cm and not
more than 100 cm from the floor.
You can extend the drain
hose to maximum 400 cm.
Contact the authorized
service centre for the other
drain hose and the
extension.
It is possible to connect the drain hose in
different ways:
1. Make a U shape with the drain hose
and put it around the plastic hose
guide.
2. On the edge of a sink - Fasten the
guide to the water tap or to the wall.
Make sure that the plastic
guide cannot move when the
appliance drains.
Make sure that the drain
hose end is not immersed in
the water. There may be a
return of dirty water into the
appliance.
3. To a stand pipe with vent-hole -
Insert the drain hose directly into a
drain pipe. Refer to the illustration.
The end of the drain hose
must always be ventilated ,
i.e. the inner diameter of the
drain pipe (min. 38 mm -
min. 1.5") must be larger
than the external diameter of
the drain hose.
4. If the end of the drain hose looks like
this (see the picture), you can push it
directly into the stand pipe.
ENGLISH 11

5. Without the plastic hose guide, to
a sink spigot - Put the drain hose in
the spigot and tighten it with a clamp.
Refer to the illustration.
Make sure that the drain
hose makes a loop to
prevent particles going into
the appliance from the sink.
6. Position the hose directly to a built-
in drain pipe in the room wall and
tighten it with a clamp.
4. PRODUCT DESCRIPTION
4.1 Appliance overview
1 32 4 11
6
7
8
9
5
12
10
13 14
1Worktop
2Detergent dispenser
3Air filter(s)
4Control panel
5Door handle
6Rating plate
7Drain pump filter
8Feet for levelling the appliance
9Airflow slots
10 Water drain hose
11 Water inlet valve
12 Mains cable
13 Transit bolts
14 Hose supports
www.electrolux.com12

5. CONTROL PANEL
5.1 Control panel description
Program
Cottons
Cottons Eco
Synthetics
Delicates
NonStop 3h/3kg
Silk
Wool/Handwash
Steam
Outdoor
Rinse
Wash
Only Drain Stain
Prewash
Only Spin Dry
Mode
23
6
12 11 10 8
1
4
5
7
9
1Programme dial
2Display
3 Drying time touch button
4 Drying level touch button
5Mode touch button
• Wash
• Dry
6 Start/Pause touch button
7 Stains/Prewash touch button
• Stain option
• Prewash option
8 Delay Start touch button
9 Time Save touch button
10 Spin reduction touch button
• Drain only
• Spin only
11 Temperature touch button
12 On/Off push button
5.2 Display
ENGLISH 13

Maximum load indicator. The icon flashes during laundry load
estimation (refer to "PROSENSE load detection" paragraph).
Maximum laundry indicator. It flashes when the laundry load ex‐
ceeds the maximum declared load of the selected programme. If
you run a programme when the drum is overloaded, also
flashes at the end of the programme.
Drying time indicator.
Door locked indicator.
The digital indicator can show:
• Programme duration (e. g. , washing and/or drying phase).
• Delay time (e. g. or ).
• Cycle end ( ).
• Warning code (e.g. ).
Washing phase indicator: it flashes during prewash and wash
phase.
Rinsing phase indicator. It flashes during rinse phase.
The permanent Extra Rinse option:
• - one additional rinse.
• - two additional rinses.
Spin and drain phase indicator. It flashes during spin and drain
phase.
Steam phase indicator.
Drying phase indicator.
Child safety lock indicator.
Temperature indicator. The indicator appears when a cold
wash is set.
Spin speed indicator.
Iron drying indicator.
Cupboard drying indicator.
Extra drying indicator.
www.electrolux.com14

6. DIAL AND BUTTONS
6.1 On/Off
Pressing this button for a few seconds
allows to activate or deactivate the
appliance. Two different tunes sound
while switching the appliance on or off.
As the Stand-by function automatically
deactivates the appliance to decrease
the energy consumption in a few cases,
you may need to activate the appliance
again.
For more details, refer to Stand-by
paragraph in Daily Use chapter.
6.2 Introduction
The options/functions are
not selectable with all
washing programmes.
Check the compatibility
between options/functions
and washing programmes in
the "Programme Chart". An
option/function can exclude
another one, in this case the
appliance doesn't allow you
to set the incompatible
options/functions together.
Make sure the screen and
touch buttons are always
clean and dry.
6.3 Temperature
When you select a washing programme,
the appliance automatically proposes a
default temperature.
Touch this button repeatedly until the
desired temperature value appears on
the display.
When the display shows the indicators
and , the appliance does not heat
the water.
6.4 Spin
When you set a programme, the
appliance automatically sets the
maximum spin speed allowed.
Touch repeatedly this button to:
•Decrease the spin speed.
The display shows only
the spin speeds available
for the set programme.
•Set the drain-only option (Skipping
the wash, rinse and spin phases):
Only Drain.
The appliance performs the only
draining phase of the selected
washing programme.
The display shows the indicator
(cold), and the indicator (no
spin) and the indicator .
•Set the spin-only option (Skipping
the wash and rinse phases) : Only
Spin.
Before setting this option,
select a suitable washing
programme for the
garments. The appliance
will performs the most
fitting spin cycle for your
garments care (e.g. For
synthetics items, first
select the Synthetics
washing programme and
then the Only Spin
option).
The appliance performs only the
spinning phase of the selected
washing programme.
The display shows the indicator
(cold), the phase indicator and the
spin speed.
6.5 Stain/Prewash
Press this button repeatedly to activate
one of the two options.
The relevant indicator goes on in the
display.
•Stain
Select this option to add an anti-stain
phase to a programme in order to
treat heavily soiled or stained laundry
with stain remover.
Pour the stain remover into
compartment . The stain remover
ENGLISH 15

will be added in the appropriate phase
of the washing programme.
This option is not
available with a
temperature lower than
40 °C.
•Prewash
Use this option to add a pre-wash
phase at 30 °C before the washing
phase.
This option is recommended for
heavily soiled laundry, especially if
containing sand, dust , mud and other
solid particles.
The options can increase the
programme duration.
6.6 Delay Start
With this option you can delay the start of
a programme in a more convenient time.
Tap on the button repeatedly to set the
required delay. The time increases by
steps of 30 minutes up to 90' and from 2
hours up to 20 h.
After starting the cycle by the means of
the Start/Pause button, the display
shows the selected delay time and the
appliance begins the countdown.
6.7 Time Manager
With this option you can decrease the
programme duration.
• If your laundry is normally or lightly
soiled, it may be advisable to shorten
the washing programme. Touch this
button once to decrease the duration.
• In case of smaller load, touch this
button twice to set an extra quick
programme.
On the display the programme duration
is adjusted accordingly.
When this button is set, the led above
the button is on.
This option can also be used
to shorten the Steam
programme duration.
6.8 Timed drying
Touch this button to set the time that
suits the fabrics you have to dry (refer to
"Timed drying" table). The display shows
the set value.
Each time you touch this button the time
value increases by 5 minutes.
You cannot set all time
values for different types of
fabrics.
6.9 Drying Levels
Touch this button to set one of 3
automatic dryness levels proposed by
the appliance.
On the display the relevant dryness
indicator goes on:
• Iron dry: laundry to be
ironed.
• Cupboard dry: laundry to be
put in store.
• Extra dry: laundry to be fully
dried.
You can not set all
automatic levels for each
type of fabrics.
6.10 Mode
Thanks to this button, a cycle can
perform:
•Only washing : Wash indicator is
on.
•Washing and drying : Wash
and Dry indicators are on.
•Only drying : Dry indicator is on.
6.11 Start/Pause
Touch the Start/Pause button to start,
pause the appliance or interrupt a
running programme.
www.electrolux.com16

7. PROGRAMMES
7.1 Programme Chart
Programme Programme description
Washing programmes
Cottons
White cotton and coloured cotton. Normal, heavy and
light soil.
Cottons Eco
White cotton and coloured cotton. Normal, heavy and
light soil.
Cottons energy saving programme. This programme at
60ºC with a load of 9 kg is the reference programme for da‐
ta entered in the energy label, in compliance with 96/60/EC
Directive. Set this programme to have a good washing re‐
sults and decrease the energy consumption. The time of
the washing programme is extended.
Synthetics
Synthetic items or mixed fabric items. Normal soil.
Wash&Dry programme
NonStop 3h/3kg
Mixed fabrics (cotton and synthetic items). Complete
programme to wash and dry laundry loads up to 3 kg in
one go. It only lasts 3 hours.
Also, the indicator appears on the display.
Washing programmes
Delicates
Delicate fabrics such as acrylics, viscose and mixed
fabrics requiring gentler washing. Normal soil.
Silk
Machine and hand washable silk and other delicate
fabrics . Drum movements are so gentle that is possible to
treat even very delicate garments. Run a complete wash
and dry cycle to reduce creases.
Wool/Handwash
Machine washable wool, hand washable wool and oth‐
er fabrics with «hand washing» care symbol1).
Outdoor Do not use fabric softener and make sure that
there is no softener residue in the detergent
dispenser.
Outdoor clothing, technical, sport fabrics, waterproof
and breathable jackets, shell jackets with a removable
fleece or inner insulation.
By performing a combined wash and dry pro‐
gramme, the drying phase also acts as water-
repellent restorer. Make sure that the gar‐
ment care label permits tumble drying.
ENGLISH 17

Programme Programme description
Steam programme
Steam programmes can be used for reducing wrinkles and odours2) of garments that
just need to be refreshed, avoiding washing. The fabric fibres are relaxed and after‐
wards ironing becomes effortless. When the programme is completed, quickly re‐
move the laundry from the drum3). Steam programme does not perform any hygienic
cycle. Do not set a steam programme with the following type of items:
• Items that are not suitable for tumble drying.
• Items with label "Dry clean only".
AEG fragrance. If you use this special gentle fragrance, your laundry will scent as
just washed: pour a single dose bottle in the compartment and simply start a
steam programme. Reduce the fragrance dosage when treating smaller load. By
means of the Time Manager button, you can reduce the programme duration when
treating items labeled to be washed at low temperature.
DO NOT:
• Tumble dry the garments treated with fragrance. Its benefit would evaporate.
• Use the fragrance with different purposes than those here described.
• Use the fragrance on new garments. New garments may contain residual finishing
compounds which are not compatible with it.
The fragrance dose bottles are available on AEG web shop or by author‐
ised dealer.
Steam
Cottons, Synthetics, Delicates. Short and gentle steam
programme to refresh even your very delicate garments, in‐
cluding very delicate garments with sequins, lace etc.
When treating smaller loads, the programme duration can
be further reduced by means of the Time Manager option.
WARNING!
Do not use this programme with wool and gar‐
ments labelled as dry-clean only.
Additional programme
Rinse
To rinse and spin the laundry. All fabrics, except woollens
and very delicate fabrics. Reduce the spin speed accord‐
ingly to the type of laundry.
1) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the
drum doesn't rotate or doesn't rotate properly, but this is normal for this programme.
2) Steam programme doesn't remove particularly intense odour.
3) After the steam treatment the laundry can be humid. Hang items out for a few minutes.
Programme temperature, maximum spin speed and maximum load
Programme Default temper‐
ature
Temperature
range
Reference spin
speed
Spin speed range
Maximum load
Washing programmes
www.electrolux.com18

Programme Default temper‐
ature
Temperature
range
Reference spin
speed
Spin speed range
Maximum load
Cottons
40 °C
95 °C - Cold
1400 rpm
1400 rpm - 400 rpm 9 kg
Cottons Eco
40 °C
60°C - 40 °C
1400 rpm
1400 rpm - 400 rpm 9 kg
Synthetics
40 °C
60 °C - Cold
1200 rpm
1200 rpm - 400 rpm 4 kg
NonStop 3h/3kg
30 °C
40 °C - 30 °C 1200 rpm 3 kg
Delicates
40 °C
40 °C - Cold
1200 rpm
1200 rpm - 400 rpm 2 kg
Silk 30 °C 1000 rpm
1000 rpm - 400 rpm 0.5 kg
Wool/Handwash
40 °C
40 °C - Cold
1200 rpm
1200 rpm - 400 rpm 1.5 kg
Outdoor
30 °C
40 °C - Cold
1200 rpm
1200 rpm - 400 rpm 2 kg
Steam 1 kg
Rinse 1400 rpm
1400 rpm - 400 rpm 9 kg
Programme options compatibility
Programme
Cottons
Cottons Eco
Synthetics
NonStop 3h/3kg
Delicates
Silk
Wool/Handwash
Outdoor
Steam
Rinse
Options
Spin ■ ■ ■ ■ ■ ■ ■ ■
ENGLISH 19

Programme
Cottons
Cottons Eco
Synthetics
NonStop 3h/3kg
Delicates
Silk
Wool/Handwash
Outdoor
Steam
Rinse
Options
Only Drain ■ ■ ■ ■ ■ ■
Only Spin1) ■ ■ ■ ■ ■ ■
Extra Rinse ■ ■ ■ ■ ■ ■ ■
Prewash ■ ■ ■ ■
Stain2) ■ ■ ■ ■
Delay Start ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Time Manag‐
er3)
■ ■ ■ ■ ■
Timed drying ■ ■ ■ ■ ■ ■
Drying Levels ■■4)
1) Before setting this option, select a suitable washing programme for the garments. The
appliance will performs the most fitting spin cycle for your garments care (e.g. For synthetics
items, first select the Synthetics washing programme and then the Only Spin option).
2) This option is not available with temperature lower than 40 °C.
3) If you set the shortest duration, we recommend that you decrease the load size. It is pos‐
sible to fully load the appliance, however the washing results can be less satisfactory.
4) Iron Dry is not available with this programme.
www.electrolux.com20