ELEKTROBOCK PT32 User manual

INTELLIGENT ROOM
THERMOSTAT
MADE IN CZECH REPUBLIC
•LARGE BACKLIT DISPLAY
with intuitive navigation in CZ/PL/EN/DE/RU/SK
•
9 WEEKLY PROGRAMS
and 6 temperature changes per day
•
HYSTERESIS/ PI/PID REGULATION
selection according to the heating system
•
ENERGY SAVINGS UP TO 30%
quick investment return
•
OPTIMALISATION OF OPERATION
preliminary switch-on function
Temp. 23
HEATING
ON
TEMPE-
RATURE
CHANGE
17°C17°C 23°C23°C
SENT
REMOTE CONTROL BY MEANS OF MOBILE PHONE
by extending the thermostat with the GST1 or GST2 module (not included in PT32)
PT32PT32

2
DESCRIPTION
PT32 is an intelligent digital room thermostat with a backlit display. Its advantages involve a quick change
in the desired temperature by simply turning the wheel, and possibility of setting up to 9 weekly programs
with 6 temperature changes per day.
INSTALLATION AND LOCATION
Install the thermostat at a suitable place where its operation cannot be affected by direct flow
of hot air from the heater, sunshine or other disturbing effects. Do not install it on an external
wall either. The installation height should be approx. 1.5 m above the floor. Place the thermo-
stat in the “reference room”, such as the living room (the heating source will switch according
to the temperature in this room).
The installation must only be done by a properly qualified person!
Before installation, disconnect the power supply!
1) Switch off the main circuit breaker.
2) Remove the control part from the lower cover of the device (Fig.1, page 3).
3) Chip away the central plastic piece from the lower cover to lead in conductors.
4) Run the conductor through the hole and connect it to the terminal acc. to the diagram.
5) Fasten the lower cover to the wiring box with screws (Fig. 2, page 3).
6) Batteries are located at the back of the control part. Remove their protective paper
(on first use), or insert new batteries (follow the instructions on page 3).
7) Mount the control part on the lower cover.
8) Switch on the main circuit breaker and test correct connection of the thermostat, see
page 12 (TEST).
9) Upon first start (or reset), the thermostat displays “SET CLOCK”, set the current time
and date according to page 5. After that select language see page 8.
Backlit display
if any button is pushed, the backlit switches on
automatically for 5 s at least
Control elements
turning
= change of the temperature set
short push
= choice confirmation (entry)
= quick change of the temperature
or program desired, viewing
the running hours (see page 4)
long push
= step back (only in the CONST
mode see pages 8-13)
push
= opening the main menu or return
a step back
MENU

3
Wiring diagram:
PT32 BOILER
*
*
potential-free
(voltage-free) contact
The thermostat
terminals are marked
differently with
every type of boiler.
Therefore, follow the
wiring prescribed by
the boiler
manufacturer!
RJ45 connector for
the module (GST1
or GST2) to control
the thermostat with
a mobile phone
MENU
Fig.1 Fig.2
Fig.3
alkal.battery
1.5V/AA
alkal.batter
1.5V/AA
BATTERY REPLACEMENT
As soon as “ “ appears on the display, you must replace
the batteries.
1) Remove the control part from the lower cover of the device (Fig. 1).
2) Replace the batteries. Heed the correct polarity marked in the battery
compartment (Fig. 3). After removing the batteries, all setting of the
thermostat are saved in the E-EPROM memory. You only have to set
the time (page 5)!
Always use the type AA, 2 x 1.5 V, alkaline batteries!
Recommendation: Check the batteries before every heating season!
Dispose of old batteries in conformity with regulations
on hazardous waste treatment!

TEMP. IN AUTO
TEMP. IN MANU
OPER HOURS H.C.
4
HINTS FOR THE USER
QUICK CHANGE OF THE DESIRED TEMP. / PROGRAM
Press the “ “ button twice, the desired temperature starts
blinking on the display. Change the temperature by turning the
“ “ button, and press the“ “ button.
In the AUTO mode, the change lasts until the next program change.
Another program can be selected in this mode in the same way.
In the MANU mode, the change is permanent.
LCD DESCRIPTION
1
2
4
678
910 12
13
14
15
16
3
5
11
17
1, Current day (in the Prog
mode, selection of days to be
programmed)
2, Heating on indication
3, Current room temperature
4, Anti-freeze temperature
5, Modes for setting programs
(PROG) and constants
(CONST) (page 6-13)
6, Automatic mode ( page5)
7, Manual mode (page 5)
8, Clock setting mode
(page 5)
9, Holiday mode (page 5)
10,Permanent shut-off (page 5)
11, Summer mode (page 10)
12,Boiler inspection indication
(page13)
13,Current time
14,Current date (various
parameters in the CONST
mode; for details, see page 6)
15,Status line, dynamically
changing according to
the process running
16,Key lock indication (page 12)
17,Low battery indication
OPERATIONAL HOURS
Push the “ “button four times. The boiler operating hours
appear on the LCD. The figure on the picture means 906 hours
43 minutes.
Resetting the counter:
When operational hours are displayed, turn the “ “ button
anti-clockwise.

AUTO MOdE
MANUAL MOdE
OFF MOdE
HOLIdAY
SET TEMP.
SET TIME
SET HOUR
5
OPERATIONAL MODES
The first push of any button activates the display backlight. Pushing the“ MENU “ button shortly
again, you open the main menu where you can choose the operational mode.
AUTO
The thermostat works according to the weekly program preset (this
program can be changed; see PROG for detailed description).
MANU (the 21 °C temperature is factory - set)
The thermostat works according to the temperature preset until
the next manual change.
OFF
The thermostat is off until the next manual change of the mode.
HOLIDAY
The thermostat keeps the temperature preset until the given date
and time. When the preset time lapses, it automatically returns to
the last-selected AUTO/MANU mode before the holiday.
Press the “ MENU “ button twice; select the AUTO mode by
turning “ “, and confirm with the“ “ button.
(the Pr3 weekly program is factory-set, see page 7)
Press the “ MENU “button twice; select the MANU mode by
turning “ “, and confirm with the“ “ button.
(anti-freeze temperature of 3°C is kept – cannot be changed)
Press the “ MENU “ button twice; select the OFF mode by turning
“ “, and confirm with the“ “ button.
Press the “ MENU “ button twice; select the mode by turning
“ “ , and confirm with the“ “ button.
Stepwise, set the temperature which the thermostat should keep
during the holiday, time and date of your return from the holiday.
Change the values by turning“ “, and always confirm them
pushing the“ “ button.
When the setting is finished, press the “ “ button to return to
the basic screen.
Note: You can cancel the holiday mode any time by choosing another
AUTO or MANU mode.
CLOCK SETTING
Setting the current time and date.
Press the “ MENU “ button twice; select the CLOCK mode by
turning “ “, and confirm with the “ “ button.
Change the values turning the “ “ button. Always push the “ “
button to confirm (the value set is always blinking; the “ “ button
returns you to the menu).

PROGRAMMING
SELECT dAY
TIME CHANGES
SELECT PROGRAM
CONSTANTS
TEST MOdE
ON OFF
6
PROG
9 weekly programs with 6 changes per day can be preset. The Pr1 and
Pr2 programs are blank; Pr3 to Pr 7 are factory-set. The PrU and PrL
programs are factory-set as well, intended for the EVEN/ODD week sele-
ction (see page 7,10 for details).
Press the “ MENU “button twice; select the PROG mode by turning
the “ “ button, and confirm with the “ “ button.
The selected program number is blinking on the display.
Choose the program you wish to modify by turning the “ “
button, and confirm with the “ “ button. By turning the “ “ button,
choose the number of days programmed (you can program
“day-by-day” or “1-5 = Mon-Fri”, “6-7 = Sat-Sun” or “1-7 = Mon-Sun”).
Confirm with the “ “ button.
The Change 1 time starts blinking. Set the time by turning the “ “
button, and confirm with the “ “ button. Enter temperature for this
time by turning the “ “ button, and confirm with the “ “ button
again. The Change 2 time appears on the display. Proceed in the
same way as with the first time change.
In this way, you can set up to 6 temperature changes per day.
To move one step back, push the “ “button shortly; to return to the
basic screen, push the“ “ button long.
After modifying the preset program, check whether all of the
changes set comply with your requests!
There is no need to apply all six changes in one day!
(PROGRAMMING)
PROGRAM SETTING MODIFICATION
CONST
Setting the control parameters. For a detailed description, see
page 8 -13.
Press twice the “ MENU “ button, choose the CONST mode by
turning the “ “ button, and press the“ “ button to confirm.
TEST
Testing the correct connection to boiler.
Press twice the “ MENU “, choose the TEST mode by turning the
“ “ button, and press the “ “ button to confirm (RELAY TEST
is showed on LCD). Turn the “ “ button to start testing.
The output relay will be switched on/off several times
(the ON/OFF messages appear on the LCD).
(CONSTANTS)

7
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.3
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.4
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.5
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.6
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.7
U
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
L
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
program No.1
program No.2
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
Tables of temperature programs
Note:
The 5/21 entry
means that the
temperature of
21 °C is
requested
at 5 o’clock
All of the
programs
given can
be
modified!

ENGLISH
TEMP.
TEMP.
TYPE OF REGUL.
t
t
T
Heating
ON
desired
temp.. hysteresis
HYSTERESIS
8
1
2
3
CESKY
Here you can set the limit of the minimum adjustable tempera-
ture. When using the GSM module, you will be informed by an
SMS that the room temperature has dropped below this value.
Select within the range from 3°C to 10°C (by 0.5°C).
4CONTROL TYPE
Press the “ MENU “button twice; select the CONST mode by turning the “ “ button, and
confirm with the “ “button.
Set the constants depending on the type of building being heated, boiler and heating system.
For select the type of regulation we recommend you consulting with an expert.
Against undesirable usage of strange person we recommend using CONST19 (password).
Language selection (CZ/PL/EN/DE/RU/SK).
Choose the language by turning the“ “ button, and confirm
with the“ “ button.
MINIMUM CONTROL TEMP.
Set the value by turning the“ “ and confirm “ “.
MAXIMUM CONTROL TEMP.
(Czech is factory preset)
(factory setting of 5°C)
(factory setting of 39°C)
Here you can set the limit of the maximum adjustable tempera-
ture. When using the GSM module, you will be informed by an
SMS that the room temperature has risen above this value.
Select within the range from 15°C to 39°C (by 0.5°C).
Set the value by turning the“ “ and confirm “ “.
(PID-regulation is factory preset)
CONSTANTS SETTING
Choose the type of control by turning the “ “ button and
press the “ “ button to confirm.
HS = Hysteresis
Difference between the desired and current
temperature.
If the hysteresis is 1 °C and the desired temperature is
20 °C, the thermostat switches off at 20 °C, and on at
19 °C (see the graph).
For correct hysteresis function, set the parameters
according to the heating system type; see CONST 5.
Note: If hysteresis is selected, CONST 6 is skipped automatically.
Selection of the control type:

TYPE OF REGUL.
HYSTERESIS
MIN TIME ON
Heating type Minimum source
switch-on time
Electric heating 1
Plate radiators 2 (3)
Cast iron radiators 4
Floor heating 5
9
PID = proportional-integral-derivative control
The PID-control principle consists in continuous
comparison of the current room temperature
with the desired temperature, and automatic
adaptation of the controller to the given
conditions. This is the most perfect continuous
control; you can achieve not only short control time,
but also high accuracy without permanent control
deviation. The minimum switch-on time is internally
set to 2 minutes, the proportional band is 2 °C, the
time interval is automatically recalculated according
to current temperature conditions.
Note: If the PID-control is selected, CONST 5 and CONST 6 are
skipped automatically.
PI = proportional-integral control
The PI-control principle consists in comparison
of the current room temperature with the desired
temperature. The PI-control aims at achieving and
maintaining the desired temperature without oversho-
oting (see the graph). For correct function of the PI-
control, set the control parameters according to the
type of the heating system with respect to the room
thermal inertia; see CONST 6.
Note: If the PI-control is selected, CONST 5 is skipped
automatically.
t
t
T
Topení
ON
požad.
teplota
PID-CONTROL
Note: The graphs are just tentative; the real con-
trol course differs according to current conditions
in the measured object!
t
t
T
Topení
ON
požad.
teplota pásmo
proporcionality
PI-CONTROL
CAUTION! ONLY IN CASE OF LOCKING BY PASSWORD (see CONST19)
If the “ “ key symbol appears on the LCD, the constant selected
cannot be modified and you must know the PASSWORD (page13,
CONST19). You can change the constant after entering the password.
After you exit the CONST mode, the security lock of the constants related
to the control will be activated automatically.
5SETTING HYSTERESIS PARAMETERS
(factory setting of 0.5°C)
(factory setting of 2min)
HYSTERESIS
MINIMUM SWITCH-ON TIME
Here you can set the minimum switch-on time of the boiler
in minutes at hysteresis. Select within the range
from 1 to 5 minutes according to the type of
the heating system used (see the table).
Set from 0.1 to 6 °C. According to the value preset, the
thermostat switches on at the temperature:
T switching = T required - HYSTERESIS
Choose the hysteresis by turning the “ “ and confirm “ “.
Set the value by turning the “ “ and confirm “ “.

MIN TIME ON
PI ZONE
Heating type Minimum source
switch-on time
Electric heating 1
Plate radiators 2 (3)
Cast iron radiators 4
Floor heating 5
PRE SWITCH MOdE
SUMMER MOdE
Odd-EVEN MOdE
10
6SETTING PI-CONTROL PARAMETERS
(factory setting of 10 min)
(factory setting of 2min)
PI-CONTROL INTERVAL
MINIMUM SWITCH-ON TIME
(factory setting of 2°C)
PI-CONTROL BAND
Select according to the object’s thermal inertia.
The optimum setting is within the range of 10 to 15 min.
The adjustable range is 5 min to 20 min (by 1min).
Set the interval by turning the “ “ and confirm “ “.
Select within the range of 1 to 5 minut. The setting is
determined by the heating system type, and depends on
the PI-control time period selection. Setting according to
the table is recommended.
Set the value by turning the “ “ and confirm “ “.
This value determines the temperature at which the PI-control
starts functioning. For example, the desired temperature is
22 °C, the proportional band is 1.5 °C. Up to 20.5 °C, the
source heats fully. When this value is reached, the PI-control
starts. The PROPORTIONAL band can be set within the ran-
ge of 0.5 to 3.0 °C (by 0.1 °C).
Set the PI band by turning the “ “ and confirm “ “.
7
This function provides for the desired temperature at the desired time.
You do not need to consider when to switch on the heating to be
warm when getting up in the morning without heating up long before
uselessly. You just program the time when you want the desired tem-
perature. In two days’ operation, the thermostat ascertains thermal
constants of the room, and then switches the heating in advance as
necessary. The preliminary switch-on time is limited to 2 hours.
PRELIMINARY START OF HEATING
Choose YES/NO by turning the“ “ and confirm “ “.
(factory setting of NO)
8
Switching the heating on is not permitted in this mode. Particularly,
this can be used in the summer period, when heating is unnecessary.
After enabling the mode, the “ “ symbol appears on the display.
Note: The anti-freeze protection (3 °C) is still functional. In this mode,
you cannot change temperature or set the holiday mode!
SUMMER MODE
Choose YES/NO by turning the“ “ and confirm“ “.
(factory setting of NO)
9
If you choose YES, the PrU and PrL programs will alternate
automatically according to the week (even / odd). This setting
is advantageous, for example, for work in shifts (requirements
on thermal comfort in the object change every week).
EVEN-ODD WEEK SELECTION (factory setting of NO)
Choose YES/NO by turning the“ “ and confirm“ “.

HEATING
TEMP CORRECT
CONTROL bY GSM
TO SENdER
TO ANOTHER NR
420000000000---
11
10
Setting of the thermostat functions.
HEATING = if the current temperature value falls below the desired
one, the output relay (for heating systems) switches on.
COOLING = if the current temperature value exceeds the desired
one, the output relay (for cooling systems) switches on.
HEATING / COOLING (factory setting of HEATING)
Choose HEAT/ COOL by turning the“ “ and confirm “ “.
11
Used to correct temperature measured by the thermostat. Setting
must earliest be done after 12-hour operation when the internal sen-
sor temperature has settled. Measure the room temperature with a
thermometer. If it differs from the thermostat temperature, set corre-
ction within the range from -5°C to +5°C.
TEMPERATURE CORRECTION
Set the correction by turning the“ “ button, and confirm with
the “ “ button.
(factory setting of 0°C)
12
This constant selects the possibility of thermostat control via
a GSM module.
NE GSM module disabled
ANO GSM module enabled. Set CONST tEL nO and CONST13!
USE GSM
Choose YES/NO by turning the “ “ and confirm“ “.
(factory setting of NO)
Note: If you choose YES and do not connect a module, the “GSM UNCONNECTED” notice appears on the LCD
basic screen. The GSM module control is described in detail in the GST1(2) instructions.
tEL nO
This constant can be set if CONST12 = YES. It specifies the
possibility of connecting a GSM module for control by means of
a mobile phone. Allows the following options:
PHONE NUMBER SETTING
1) TO SENdER = SMS will be sent back to
the telephone number from which the
message was sent.
2) TO ANOTHER NR = SMS will be sent back to
the telephone number entered in
the thermostat.
3) bOTH NUMbERS = SMS will be sent back to both
telephone numbers (combination options
1 and 2).
When choosing 2) and 3) option we enter a phone number
n the international format (420123456789), to which return
SMS messages on the thermostat condition should be sent.
Is possible to enter a phone number min. 10-digit to 15-digit.
Turning the “ “ button, enter the phone number stepwise; confirm each setting with the
“ “ button.
For automatically receiving SMS about exceeding the limits (CONST2 and CONST3) is requi-
red to enter the phone number into the thermostat option 2) or 3).

ENTER PIN
14 TEST GSM
ERROR PIN
ON OFF
15 RELAY TEST
LOCK
12
13
This constant can be set if CONST12 = YES. It specifies the possibility
of connecting a GSM module for control by means of a mobile phone.
Enter the PIN code of the SIM card inserted in the GST1 or GST2
module.
PIN CODE SETTING
Turning the “ “ button, enter 4 digits stepwise; confirm each
setting with the “ “ button.
14
After setting the PIN code of the SIM card inserted in the
thermostat is performed to test the GSM module and PIN
validation.
GSM TEST
Turning the “ “ button to start test of GSM module and chec-
king of PIN code.
The“ “ button displays the next constant,; pushing “ “ you
return to the main menu.
One of the following messages appears on the thermostat after connecting GSM module
and turning “ “ button:
Checking the GSM
module.
Modul is connected and
PIN is entered correctly.
Wrong PIN, reset PT32
and connect module again.
Testing the correct connection the thermostat to boiler
(this function is identical with the TEST mode in the main menu).
Start the test by turning the “ “ button. The output relay is
switched on/off several times (the ON/OFF messages appear
on the LCD). The “ “ button displays the next constant;
pushing “ “ you return to the main menu.
RELAY TEST
15
KEY LOCK
Used for locking control elements as a protection against unde-
sirable intervention by a stranger.
16
Choose YES/NO by turning the “ “ and confirm “ “.
(factory setting of NO)

KEYCOdE
SERVICE dAY
20 VERSION
19 PASSWORd
13
20 VERSION (factory setting restoration)
Firmware version, for information only.
If you push the “ “ button long (for approx. 3 s), the RESET
text appears shortly on the LCD, and the thermostat restores its
factory settings!
KEY CODE
This constant can be set if CONST16 = YES. It enters a code
used for enabling control elements.
A 4-digit combination is set (range from 0 to 9).
The keys are locked within 1 minute (after opening the basic
screen). The “ “ symbol appears on the LCD.
After you push the “ “ or “ “ button, the LCD asks you to en-
ter the key code; after entering the correct code, you can make
any modifications (control elements are functional again).
17
BOILER OVERHAUL NOTIFICATION
Set the date on which you want to be reminded of the prescribed
boiler service. On the desired date, the “MAINTENCE NECES-
SARY” message and the “ “ symbol appear in the LCD bottom
line (the message can be cancelled by entering the next boiler
overhaul date!).
18
Turning the “ “ button, enter 4 digits stepwise, and confirm
each setting with the “ “ button.
RECOMMENDATION: - Note the key code in the table
- You can cancel the code by the NO option in CONST16 or by
restoring the factory setting of the thermostat (see CONST 20).
YOUR CODE
Turning the “ “ button, enter the day, month and year stepwise;
confirm each setting with the “ “ button.
(factory set to 01/01/2030)
19 PASSWORD (not set by default)
It is used for locking the constants related to the given control
settings. Suitable for service technicians.
After a numerical code has been entered, the user
cannot change constants No. 4, 5, 6 and 10.
If you open the CONST mode and browse the constants, the
“ ” symbol appears next to the constants locked; if you turn
the “ “ button, the password is required! Unless you enter
the password, the constants remain locked. To try to unlock
them again, you must exit the CONST mode and browse up the
constant locked again.
Turning the “ “ button, gradually enter four digits and confirm each setting with
the “ “.

14
USING GSM MODULE (GST1 or GST2)
1) Mount and set the PT32 thermostat according to the instructions.
2) Set CONST12 to YES (use GSM); then, set CONST tEL nO and CONST14 according to
the instructions on page 11-12.
3) Insert an activated SIM card in the GST1 (or GST2) module.
4) Interconnect the thermostat and GSM module with a data cable (delivered with GST1 or
GST2). Connect the GSM module power source to the 230 V / 50 Hz mains (the green
LED lights up, and the orange one is blinking on the module).
5) As soon as the orange diode lights up, test correct connection of CONST14
(see page 12: TEST) – connection should always be established automatically within
3 minutes without the TEST function.
The PT32 thermostat can be controlled by means of a mobile phone by simply extending it by
the GST1 or GST2 module (not included – must be purchased). For correct commissioning,
the following procedure must be followed:
Example of using PT32 in connection with GSM module:
The thermostat is located in an object where anti-freeze temperature (e.g., 7 °C) must be
kept.
1. Connect PT32 strictly according to the instructions.
2. Select the MANU mode.
3. Pushing the “ “ button and turning the “ “ , set the thermostat temperature to 7°C.
4. Before entering the object, enter the “Temp 23” SMS in your mobile phone, and send it to
the module number connected to the thermostat.
The thermostat receives the message and automatically switches the heating system on until
the desired temperature is achieved. Next, the PT32 automatically sends a RETURN SMS to
inform you about the temperature change made. Entering the object, you can adjust the tem-
perature on the thermostat directly at will.
INFORMATION IN THE LCD DYNAMIC LINE
REQUIR TEMP Information on the desired temperature preset
PROGR 3 PERIOd 2 Information on the program preset (e.g., 3) and the time interval running
(interval 2)
HOLIdAY IN 22.7 Only displayed in the holiday mode; informs on the end of holiday when the
thermostat restores the last selected AUTO/MANU mode.
SMS RECEIVEd Information the thermostat received new SMS
SIGNAL GSM x Determines the signal strength at the place where the thermostat is
located; where x is a value within the range from 0 to 5 (with GSM module):
0..undeterminable or no signal detected
1..worst level
5..best level of signal

15
FORMS OF MESSAGES SENT
Info Information on the heating system status
Auto Setting AUTO mode, thermostat will be work acc. last setting weekly program
Manu Setting MANU mode, thermostat will be keep last setting temperature
Off Heating system switched off permanently. ; to cancel the function, use the
Temp xx message, thermostat will automatically enter into the MANU mode with the given tem-
perature or SMS message Auto (for AUTO mode) or Manu (for MANU)
Temp xx Required temperature change (only integer numbers can be entered, within the permitted range
of maximum and minimum temperatures –CONST2 and CONST3).
Call Back call
FORMS OF BACK MESSAGES FROM THE THERMOSTAT
xx = temperature value in °C (always a two-digit number, e.g. 05)
Any type of mobile phone can be used for sending and receiving back
messages! If you can set the font size (format) in your phone, always use the
MEDIUM size when writing messages (if there are three options), or the BIG size
(if there are two options).
!
Requir: xx.x Temperature required (user set)
Act: xx.x Current room temperature
Set on
Set off
Heating system on
Heating system off
AUTO
MANU
OFF
Thermostat in automatic AUTO mode
Thermostat in manual MANU mode
Thermostat in the OFF mode (permanently off)
Sig: x Signal strength at the place where the module is located; where x is the value within the
range of 0 to 5:
0..undeterminable or no signal detected
1..the worst strength
5..the best signal strength
Battery! indicates low battery in the thermostat
No accept! Error indicated (wrong SMS format, etc.)
xx.x = temperature value in °C
BACK MESSAGES ARE SENT WITHIN 3 MINUTES!
Note: If the minimum/ maximum room temperature (preset CONST 2 and 3) is exceeded, the
“WARNING” SMS is automatically sent in a form similar to that in the Info form (only if you enter phone
number to the thermostat, see CONST tEL nO).
Info: If using a credit card, you must make a paid call once in 3 months. This call is executed
automatically (in 80 days, between 4 and 9 PM) to the phone number entered in the thermostat
(CONST tEL nO); after 20 s, the call is terminated automatically.
You can execute this function earlier by means of the “Call” SMS message.

Pb
LEAD FREE
in compliance with s RoHS
136.5 28.5
83
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel./fax: [phone]
MADE IN CZECH REPUBLIC
In case of guarantee
or post-guarantee
service, send the
thermostat to the
manufacturer’s
address.
INTELLIGENT THERMOSTAT PT32PT32
WARRANTY CERTIFICATE
(a 2-year warranty is granted for the product)
Product number: Date of sale:
Shop stamp:
Checked by:
Technical parameters
Power supply 2 x 1.5V alkal. batteries type AA
Number of temp. changes 6 temperature changes per day
Hysteresis 0.1 to 6°C
Minimum program. time 10 minutes
Adjustable temp. range +5°C to 39°C
Temperature setting by 0.5°C
Minimum indication step 0.1°C
Measurement accuracy ± 0,5°C
Battery life heating season
Protection IP20
Protection class II
Output max.5A (potential-free contacts)
Working temperature 0°C to +40°C
Dimensions:
9 weekly programs
6 temperature changes per day
programming by 10 minutes and 0.5 °C
programming “day-by-day” or Mon-Fri,
Sat-Sun and Mon-Sun
big backlit graphic display
possibility of setting HYSTERESIS,
PI regulation or PID regulation
preliminary heating start function
short-term change in the required temp.
manual mode (MANU)
permanent off (OFF)
HOLIDAY mode
summer mode
even-odd week selection
current temperature correction
key lock
boiler operating hours total
boiler maintenance indication
anti-freeze protection (3 °C)
TEST function
automatic SUMMER/ WINTER time
change
flat battery indication
possibility of using GSM module (GST1
or GST2) for control with mobile phone
PT32 is a battery-powered room temperature. The big, well-arranged
graphic display offers intuitive navigation in the selected language
(CZ/ PL/ EN/ DE/ RU/SK). The backlit display enables thermostat control even
at night. The thermostat can be connected to all boilers requiring potential-
free (voltage-free) switching contacts (such as gas boilers, electric
boilers, circulation pumps, thermoelectric drives or conditioning units).
www.elbock.cz
Properties:
Remote control modules:
The PT32 thermostat
can be equipped with
GSM modules for
remote control of the
thermostat by means
of a mobile phone.