ELEKTROBOCK BT710 User manual

BT710 User manual
Wireless thermostat
www.elbock.cz

3
Contents
Installation ............................................4
Controls (overview).................................5
Setting Time..........................................6
Pairing with Receivers.............................7
Deleting a Receiver ................................9
Setting a Programme ............................ 10
Operating Modes................................. 12
Holiday Mode...................................... 13
Setting Constants ................................ 14
Changing the desired temperature
and programme, operating clock ............ 16
Changing Batteries............................... 18
Error Messages ................................... 19
Tips ................................................... 19
An Example of the Setting of a One-week
Programme.........................................20
Navigation Card ...................................22

4
Installation
AAA AAA
Insert 2 x 1,5 V AAA alkaline batteries.
Remove the transmitter’s front cover.
Fasten the front cover on the back cover.
1
2
Mount the back cover on the wall.
Free-standing Mount:
Always use only 2 x 1,5 V AAA batteries!
(Do not use rechargeable batteries).
Avoid places like: windowsills, televisions,
PCs or devices with heat or cold emission.
1
2
Slide the thermostat on the stand and secure it
by turning it.
!
!
A B
C D
Dispose of old batteries according to
regulations for hazardous waste treatment!
!

5
Controls (overview)
Operating modes:
OFF, Programming,
Auto, Holiday
Current day
of the week
Desired
temperature
Non-freezing
temperature 3 °C
Current temperature Turned-on heating indication
Buttons lock
indication
Time
Signal transmission
Low battery
The first push of any button activates backlight.
a short push of the MENU button = ENTER
a long push of the MENU button (ca. 2 s) = a step back
-
+
MENU
-
+
MENU
MENU
Functions of the Controls
1. push
2. push

6
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
Setting Time
2x MENU .
Basic view
AUTO or MANU
appears
The hour indicator is
flashing.
Set the current hour with
the / buttons.
Using the button,
find „CLOC“.
Confirm the setting
by pushing MENU 1x.
Confirm by 1x MENU .
Set minutes, seconds, day,
month and year in the same
way.
Confirm every setting with the
MENU button.
To return to the basic mode,
hold the MENU button long.
A
D
B
E F
G
C

7
Pairing with Receivers
BT001 receiver
BT003 receiver
BT002 receiver
002
-
+
MENU
-
+
MENU
-
+
MENU
Shortly, for about 1 s, push the function button on the RECEIVER.
Both diodes will start flashing after
pushing the FUNCTION BUTTON.
*The receiver has to be connected according to the diagram (see the manual for the
corresponding receiver) and has to be energized.
Using the button,
find „COnSt“.
Push
MENU 3x.
A
E
B C
-
+
MENU
tESt 1- appears
on the display.
D
LED1 LED2
2x MENU .
Basic view
AUTO or MANU
appears

8
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
Send a signal to the
receiver by pushing the
button.
Both LEDs turn on simultaneously several times and the output
relay turns on and off multiple times.
“rest On / test Off” appears alternately on the display of
thermostat.
Wait for about 10 s for the synchronization to finish.
NOW THE 1. RECEIVER IS PAIRED.
Push the MENU button long 2x to
return to the basic view.
LED1 LED2
To return to the basic view, press long 2x MENU
button.
Shortly push the FUNCTION
button on the second receiver
for about 1 s, after which both
diodes will start flashing.
Send a signal to the second receiver by pushing the
button.
Push the button
1x and “tESt 2-”
appears on the
display.
Do you wish to pair
a2nd receiver
with this transmitter?
NO
YES
F
H
GReceiver
If the Ertr (communication error) message appears on the display, the learning process was
not carried out correctly and the whole procedure has to be repeated.
!

9
Deleting a Receiver
-
+
MENU
-
+
MENU
-
+
MENU
Using the button,
find „COnSt“.
Push MENU 3x.
tESt 1- appears
on the display.
Now the receivers are
deleted from the thermostat.
A B C
-
+
MENU
-
+
MENU
Push 9x.
tESt dEL appears
tESt 1A appears
Press the button.
D E
While using multiple receivers, individual receivers cannot be deleted.
Only all the receivers can be erased all at once.
i
2x MENU .
Basic view AUTO or MANU
appears

10
Setting a Programme
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
U1 (1st temperature change)
appears on the display.
Set a temperature with the
/ buttons and confirm it
with the MENU button. Confirm it with the MENU button.
P1 flashes on the display
(= the first one-week
programme*).
Push the MENU button 1x.
U1
1 (= Monday) flashes on the right side. Using the /
buttons, select day(s) to be programmed.
Then push the MENU button 1x.
1 = Monday
2 = Tuesday
.
.
.
6 = Saturday
7 = Sunday
12345 = Mo-Fr
67 = Sa-Su
1234567 = whole week
Desired temperature
Time
Set the time for this
temperature using the
/ buttons.
F
D
G
E
2
3
4
5
2
3
4
5
U2
-
+
MENU
-
+
MENU
-
+
MENU
Using the button,
find “PROG”.
Push MENU 1x.
A B C
2x MENU .
Basic view AUTO or MANU
appears
*It is possible to set up to 7 one-week programmes.

11
-
+
MENU
-
+
MENU
Set a temperature with the /
buttons and confirm it with the
MENU button.
U2 (2nd temperature change)
appears on the display.
U3 now appears on the display to set a third temperature change.
Use the same method as for the setting of the previous temperature stages.
In this way, up to six temperature changes per day can be set.
After the setting is done, hold the MENU button long 1x to select other days of the week
or
push the MENU button long 3x to return to the basic view.
In order for the thermostat to work according to the programme set, the AUTO operating
mode has to be enabled.
You can find the process of setting the thermostat modes on
page 12.
You can find an example of the process of setting a one-week programme
on page 20.
Confirm it with the MENU button.
Desired
temperature
Time
Set the time for this
temperature using the
/ buttons.
H I
2
3
4
5
2
3
4
5
U2
U1
i
i
-
+
MENU

12
Operating Modes
-
+
MENU
-
+
MENU
-
+
MENU
AUTO
OPERATING MODE CHANGE
MANU OFF
In the MANU mode, the
thermostat maintains one
set temperature, until it is
manually changed.
The thermostat is turned
off.
In the AUTO mode, the
thermostat works according
to the set one-week
programme.
-
+
MENU
-
+
MENU
The desired mode –
AUTO,MANU or
OFF – can be selected
with the /
buttons.
Confirm the selection of the
respective mode with the
MENU button.
A B
-
+
MENU
-
+
MENU
It is recommended to use the
OFF mode when the heating
season is not under way.
Anti-freezing protection
(3 °C) is still enabled.
i
i
2x MENU .
Basic view

13
Holiday Mode
The thermostat maintains a set temperature until a specified time and date.
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
-
+
MENU
Set the desired temperature for
the time of the holiday with the
/ buttons and confirm
it by pressing MENU 1x.
Using the button, find
AUTO
or MANU .
Set the hour of the end of the
holiday with the /
buttons and confirm it by
pressing MENU 1x.
Then push the
MENU button long 1x to return
to the basic view.
The date of the end of the holiday
appears on the display.
Then set the minute, day,
month and year of the end
of a holiday and confirm the
setting of each figure with the
MENU button.
After the specified time, the
thermostat will return to the
previously set AUTO or MANU
mode.
The Holiday Mode can be
deactivated by selecting
a different operating mode
(see p. 12).
Push MENU 1x.
A
G H
D
B
E
C
F
AUTO or MANU
appears
i
i
2x MENU .
Basic view

14
Setting Constants
-
+
MENU
-
+
MENU
1. 2. 3. 4.
Set the appropriate value
with the / buttons
and confirm it with the
MENU button.
A
D
AUTO or MANU
appears
1. Measured Temperature Correction
(-5 °C to +5 °C)
-
+
MENU
-
+
MENU
Using the button,
find „COnSt“.
Push MENU 1x.
B C
-
+
MENU
Const
MEASURED
TEMPERATURE
CORRECTION
“OPEN
WINDOW”
FUNCTION
PAIRING WITH
RECEIVERS
FIRMWARE
VERSION/
RESET TO FACTORY
DEFAULTS
This constant is used for the manual
comparison of deviations between the
real and the measured temperatures
(this may be caused, for instance,
by an inappropriate placement of the
thermostat).
i
2x MENU .
Basic view
Graphical depiction of constants:

15
-
+
MENU
To activate this function, select the “y”
symbol using the
/buttons, and to deactivate
this function, select the “–” symbol.
Confirm by pressing the MENU button.
E
F
2. “OPEN WINDOW” Function
3. Pairing with Receivers
If the temperature in the room drops sud-
denly by 1-2 °C in 2 minutes, the thermos-
tat sends out a signal to turn off the heating
appliances in order to save energy.
The thermostat returns to a normal mode
as soon as the temperature rises again.
See page 7.
Confirm by pressing the MENU button.
The activation of this function is indicated in
basic view by
the OPEN sign.
i
Information about the firmware version
appear under the constant 4.
i
-
+
MENU
If you push the button long (for more than
3 seconds), the RESET message appears on
the display and the thermostat returns to factory
defaults.
All settings will be deleted by this!
G4. Firmware Version/
Reset to Factory Defaults
!

16
Changing the desired temperature
and programme, operating clock
C
°
-
+
MENU
-
+
MENU
-
+
MENU
A long push of MENU
= return back.
=117 hours and 8 minutes
Operating clock – example:
2x the button
or
2x the button
A
D
E
-
+
MENU
-
+
MENU
The desired temperature
figure will start flashing. The
temperature can be changed
with the or buttons.
The counter can be reset
by a long push of the
button for 3 s.
A long push of MENU
= confirmation and return
back.
A short push of MENU
= activation of another pro-
gramme.
B C
-
+
MENU
When the AUTO mode is activ
A change of the desired
temperature in the AUTO
mode remains valid only
until the next change in the
programme.
!
Basic view
i
i
Heating system
operating clock
Another one-week programme
can be activated with the or
buttons.
A long push of MENU
= confirmation and return back.
A short push of MENU
= view the operating clock.

17
-
+
MENU
2x the button
or
2x the button
A
-
+
MENU
-
+
MENU
The desired temperature
figure will start flashing. The
temperature can be changed
with the or buttons.
B C
When the MANU mode is activ
Basic view
-
+
MENU
A long push of MENU
= return back.
Heating system
operating clock
D
The counter can be reset
by a long push of the
button for 3 s.
i
A long push of MENU
= confirmation and return
back.
A short push of MENU
= view the operating clock.
=117 hours and 8 minutes
Operating clock – example:
i

18
Changing Batteries
-
+
MENU
Low batteries are indicated
by the symbol.
A
Remove the transmitter’s front cover.
B
AAA AAA
Insert 2 x new 1.5 V AAA microbatteries.
C
Fasten the front cover on the back cover.
1
2
D
Always use 2 x 1.5 V AAA
alkaline batteries!
(Do not use rechargeable batteries)
!
Dispose of old batteries according
to regulations for hazardous waste
treatment!
!

19
Error Messages
Tips
-
+
MENU
Ertr = Connection error.
The number after the Ertr message states which one of the
receivers is not communicating with the thermostat (e.g. Ertr2
means that the second receiver is not communicating).
Possible solutions:
A. If the error occurred while pairing the receiver with the transmitter, repeat the pairing process –
see p. 7.
B. The error occurred during normal operation after a certain period of usage:
Check if the symbol indicating low batteries is not shown on the thermostat.
When the heating season is not under way, it is recommended to enable the OFF operating
mode – see p. 12.
It is not recommended to remove the batteries from the thermostat while it is paired with a plugged-
in receiver, as in this case the receiver will switch to a mode in which it will be ON for 2 minutes
and OFF for 8 minutes regardless of the current temperature.
It is also not recommended to leave a paired receiver unplugged, as in this case the thermostat will
start transmitting a so-called Search Signal, which will cause a quick depletion of the batteries.
A simultaneous push of the MENU and buttons in the basic view = keys locked.
A simultaneous push of the MENU and buttons in the basic view = keys unlocked.
If green LED1 is flashing, the code in the receiver was deleted and the pairing
process has to be repeated – see p. 7.
If green LED1 is constantly shining, remove the batteries from the thermostat for
2 minutes and unplug the receiver for 2 minutes as well. Then insert the batteries
back into the thermostat and plug the receiver in. After a short while, the devices
should pair again.
If it IS, replace the flat batteries with new ones.
If NOT, check if the green LED1 on the receiver is flashing or constantly shining.

20
Set 22 °C using the
button.
Push the MENU button 1x.
The time indication 0:00 is
now flashing on the display.
Set 7:00 using the
button.
Push the MENU button 1x.
U2 (2nd temperature
change) appears on the dis-
play and 22 °C is flashing.
Set 18 °C using the
button.
Push the MENU button 1x.
The time 7:00 is now flashing
on the display.
An Example of the Setting of
a One-week Programme
18°C 18°C
22°C 23°C
18°C
7:00
U1
8:30
U2
16:00
U3
21:00
U4-U6
Hours
Temp. (°C) Mo-Fr
18°C
23°C
18°C
7:00
U1
21:00
U2-U6
Hours
Temp. (°C) Sa-Su
Push the MENU button 2x
and select the PROG mode
using the button.
Push the MENU button 1x.
P1 is flashing on the display
(= the first one-week
programme).
Push the
MENU button 1x.
A small number 1
(=Monday) is flashing on
the display.
Push the button 7x.
1,2,3,4,5 (= Monday to
Friday) is now flashing on the
display.
Push the MENU button 1x.
U1 (1st temperature
change) appears on the
display and 19 °C is flashing.
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5
2
3
4
5