ELEKTROBOCK BPT710 User manual

1
BPT710BPT710
WIRELESS
ROOM
THERMOSTAT
FOR CONTROL OF HEATING DEVICES
• direct heaters
• floor heating
• radiant panels, infra-panels
• gas and electric boilers (only with the BPT002 receiver)
Comfortable control of:

2
FUNCTION DESCRIPTION
BPT710 is a wireless thermostat (transmitter) which according to the required room tempe-
rature controls the receiver unit, BPT001, BPT002 or BPT003, which switches the heating
device connected.
DESCRIPTION AND CHARACTERISTICS OF ELEMENTS PHOTO
BPT710 wireless thermostat (transmitter)
measures temperature in the room and controls heating according to•
the required temperature
enables setting of 7 weekly temperature programs with 6 changes per•
day
can switch up to 9 receivers (BPT001, BPT002, BPT003)•
modern design and backlit display•
BPT001 wireless receiver – under switch
receiver with switched phase (suitable for, e.g., direct heaters and•
panels)
switches the heating device by request and sends back confirmation•
simple installation into a wiring box•
receiver statuses indicated by LED diodes on the front panel•
automatic activation in the system after a short-term power loss (E-E-•
PROM)
BPT002 wireless receiver - wall
receiver with potential-free contact (suitable for boilers, etc.)•
switches the heating device by request and sends back confirmation•
simple installation into a wiring box•
receiver statuses indicated by LED diodes on the front panel•
automatic activation in the system after a short-term power loss (E-E-•
PROM)
BPT003 wireless receiver – in the socket
receiver with switched phase (suitable for. e.g., direct heaters and•
panels)
switches the heating device by request and sends back confirmation•
simple installation into an electric socket directly•
device simply connected by inserting into the socket (suitable for•
heaters with plug outlet)
receiver statuses indicated by LED diodes on the front panel•
automatic activation in the system after a short-term power loss (E-E-•
PROM)

3
BPT710 INSTALLATION
- Lift off the front cover of the transmitter acc. to Fig. 1.
- Fasten the back cover to the wall (or on the wiring box directly); see Fig. 2.
- Insert 2 x 1.5 V alkaline batteries, type AAA (not included in the packing); heed the
correct polarity!
- Fasten the front cover on the back one; see Fig. 4, 5.
- Necessity of battery exchange is indicated by the “ ” LCD symbol.
- Always use the 2 x 1.5 V alkaline batteries, type AAA! (Do not use rechargeable batteries.)
- For correct function of BPT710, activate the receivers according to the instructions
on page 7!
Note: Dispose of old batteries according to regulations for hazardous waste
treatment!
Holes for fastening
screws
Fig.3 Fig.4
Fig.2
Fig.5
Fig.1

4
MENU
4
DISPLAY DESCRIPTION
DESCRIPTION OF CONTROL BUTTONS
1, Current day (in the Prog mode, selection of the
number of days to be programmed)
2, Operating mode OFF/PROG/AUTO/MANU/
=HOLIDAY
3, Current room temperature
4, Heating on indication
5, Key lock indication
6, CLOC mode indication (current day and time
setting)
7, Wireless signal transmission indication
8, Low battery indication
9, Required temperature and current time display/
list of operating modes (this line is explained in
detail for every mode)
10,Indication of anti-freeze temperature of 3°C
MENU button:
short press = opening the main menu and confirmation
(ENTER)
long press (for approx. 3 s) = return from current mode
/ button:
in the basic mode = opening info
in the main menu =browsing and setting current values
simultaneous press of the MENU and buttons (in the basic
mode) = locking of the keys
simultaneous press of the MENU and buttons (in the basic
mode) = unlocking of the keys
simultaneous press of the MENU and /buttons (in the
main menu) = return to the basic mode
Note: By pressing any button first, you activate the LCD
backlight!

5
OPERATING MODES
By pressing any button first, you activate the display backlight. By another short press of
the MENU button, you open the main menu in which you can choose operating modes.
AUTO
The thermostat works according to the weekly program settings.
Press the MENU button and choose the mode AUTO with the
/ button; press the MENU button to confirm.
MANU
The thermostat works according to the manual temperature setting which re-
mains current until the next manual change.
Press the MENU button and choose the mode MANU with the
/ button; press the MENU button to confirm.
(default temperature setting of 21°C)
OFF
The thermostat is switched off until the next manual change of the mode.
Press the MENU button and choose the OFF mode with the / but-
ton; press the MENU button to confirm. The anti-freeze mode is still enabled!
HOLIDAY
The thermostat maintains the preset temperature until the given time and date.
After expiry of the preset period, it automatically returns to the previously set
AUTO / MANU mode.
Press the MENU button and choose the AUTO or MANU mode with the
/ button; press the MENU button to confirm.
Press the MENU button again and choose the mode with the /
button; press the MENU button to confirm.
The temperature value is flashing on the LCD; set the required temperature
with the / button and confirm it with the MENU button. Then set
the hour, minute, day, month and year when your holiday ends; confirm each
setting with the MENU button.
After the setting, the HOLIDAY mode will be automatically activated within
1 minute!
The LCD shows the date of the end of the holiday!

6
CLOC
Setting the correct day and time.
Press the MENU button and choose the mode CLOC with the
/ button; press the MENU button to confirm.
The current hour value is flashing on the LCD; set the current hour with the
/button and confirm with the MENU button. Stepwise, set minutes
and seconds; then the current date appears; again, set the current day, month
and year with the / button.
Confirm each setting with the MENU button.
PROG
Setting the weekly programs (7 weekly programs available with up to
6 changes per day).
Press the MENU button and choose the PROG mode with the /
button; press the MENU button to confirm. P1 (the first weekly program) is
flashing on the LCD, confirm with the MENU button. The number of days
programmed appears, choose one of the options with the / button
(you can program day-by-day or in day blocks of Mon-Fri, Sat-Sun or
Mon-Sun). Press the MENU button to confirm.
When U1 appears, set the temperature of the 1st temperature change with
the / button and confirm it with the MENU button.
Set the switching time with the / button and confirm it with the
MENU button again.
U2 appears on the LCD for setting the 2nd temperature change.
Proceed in the same way as with the 1st change.
In this way, you can set up to 6 temperature changes per day. To return to the
basic mode, simultaneously press the MENU and / buttons.
CONST
Setting of control parameters.
Press the MENU button and choose the CONST mode with the /
button; press the MENU button to confirm; the first constant appears on the
LCD.

7
1
Set the pertinent value with the / button; confirm it with the
MENU button.
It is used for correcting the temperature measured by the thermostat. We
recommend that you do the setting after 12-hour operation when the inter-
nal sensor temperature settles. Measure the room temperature with a ther-
mometer; if it differs from the thermostat temperature, set the correction
within the range of -5°C to +5°C.
CURRENT TEMPERATURE CORRECTION
2
To enable this function, set the „ A“ option with the / button and
confirm it with the MENU button. To disable, choose the „ -“ symbol and
confirm it with the MENU button.
If the room temperature drops suddenly (by 1-2 °C in 2 minutes), BPT710
sends out a signal to switch off the heaters to save energy in this way.
“OPEN WINDOW” FUNCTION
If the function is active, the UtLUM message appears on the display.
The mode is terminated if the temperature rises, or after 30 minutes.
3
If you do not want to activate another receiver, simultaneously press the
MENU and / buttons to return to the basic mode.
This function is used for activation of up to 9 receivers.
ACTIVATION OF RECEIVERS
The display shows tESt 1-, where 1 indicates the sequence of the activated
receiver. Press the „FUNCTION BUTTON“ on the receiver (for about
1.5 s), thus you introduce the receiver into the learning state (see the
pertinent receiver manual – BPT001, BPT002 or BPT003). The LED1 and
LED2 diodes are flashing alternately on the receiver. Press the button
on the BPT710 transmitter; tESt On 1A/tESt OFF 1A appears on the LCD
and the code is send to the receiver. Code acceptance is confirmed on the
receiver by simultaneously flashing diodes, thus the activation is comple-
ted. To activate the next receiver, proceed in a similar way.
Choose another receiver with the button, tESt 2- appears on the
LCD. Introduce the next receiver into the learning state by pressing the
„FUNCTION BUTTON“ (for about 1.5 s) and start the activation with the
button on BPT710. In this way, you can gradually activate up to
9 receivers.

8
DEACTIVATION OF RECEIVERS
For deactivation, choose the tESt nUL option with the button and
confirm with the button. Thus all the receivers will be disabled!
PTo return to the basic mode, simultaneously press the MENU and
/ buttons.
Communication error between the receiver and transmitter is indicated by
the ErPr1 message on BPT710, where the last number is a sequence num-
ber of the receiver activated incorrectly.
4
Information on the firmware version. If you press the button
long (for approx. 3 s), the rESEt message appears on the display
shortly and the thermostat resumes the factory setting!
FIRMWARE VERSION / FACTORY SETTING RESTORATION
By pressing the / button in the basic mode, you can view the following information:
Press the / button in the basic mode; the LCD shows the required
temperature value in the current operating mode (can be changed with the
/ buttons; in the AUTO mode, the change is short-term – lasts until
the next program change; in the MANU mode, it is permanent;
By further pressing the MENU button, you can move on to the next info
It is used for quick change of the selected program in the AUTO mode. If both
P1 and P2 programs are set, they can, for example, be changed with the
/ button;
By further pressing the MENU button, you can move on to the next info
SELECTED PROGRAM NUMBER – only in the AUTO mode
OTHER FUNCTIONS
INFO
REQUIRED TEMPERATURE

9
The LCD shows data on the operating hours of the heating device.
The hours can be reset by pressing the button for about 3 s.
By pressing the MENU button for approx. 3 s, you return to the basic mode.
OPERATING HOURS
In the basic mode, press simultaneously the MENU and buttons; the keys will be locked (key sign
appears on the LCD); unlocking can be done by simultaneously pressing the MENU and .
LOCK
ANTI-FREEZE PROTECTION
If the room temperature drops below 3 °C, the heating is switched on automatically (the symbol
appears on the display). As soon as the temperature rises, the thermostat resumes the preset mode
and controls according to the required temperature.
EXAMPLE OF CONNECTION
concealed
installation
BPT001
(receiver)
wall
installation
BPT710
(transmitter)
wall
installation
BPT002
(receiver)
socket
installation
BPT003
(receiver)

10
WIRELESS ROOM THERMOSTAT BPT710BPT710
The BPT710 wireless thermostat can bring you substantial savings, not only in the energy
necessary for heating, but also in the costs resulting from heating system installations. BPT710
can control up to 9 switching elements (receivers). The elements are switched subsequently
to prevent current surges in the mains. The coverage in built-up area is approx. 35 m.
ELEKTROBOCK CZ s.r.o.
Blanenská 1763
Kuřim 664 34
Tel.: [phone]
www.elbock.cz
MADE IN CZECH REPUBLIC
Pb
LEAD FREE
in compliance with RoHS
WARRANTY CERTIFICATE
(a 2-year warranty is granted for the product)
Product number: Date of sale:
Shop stamp:
Checked by:
In case of guarantee or post-
guarantee service, send the
thermostat to the manufacturer’s
address.
Characteristics:
7 weekly programs with 6 temperature
changes per day
backlit display
modes: AUTO/MANU/OFF/HOLIDAY
quick change of the required temperature
possibility of programming day-by-day or in
blocks of Mon-Fri, Sat-Sun, Mon-Sun
information on operating hours
child lock – key lock
automatic transfer to SUMMER / WINTER
time
„OPEN WINDOW“ function (automatic
switch-off of the heating during ventilation)
optional setting of the current temperature
correction
anti-freeze protection (3°C)
DECLARATION OF CONFORMITY
We, ELEKTROBOCK CZ s.r.o., herewith declare that the product BPT710 conforms to the basic require-
ments and other corresponding provisions of the Directive 1999/5/EC.
Issued: 01.04.2012 on www.elbock.cz
TECHNICAL PARAMETERS
Power supply 2 x1.5 V AAA alkaline batteries
(not included in the packing)
Communication type two-way
HF power < 10 mW
Frequency 433.92 MHz
Hysteresis 0.2°C
Number of temp. changes 6 temp. changes per every day
Minimum program time 10 minutes
Temperature setting range by 0.5°C
Temperature setting 5 to 39°C (anti freeze 3°C)
Minimum indication step 0.1°C
Measurement accuracy ± 0.5°C
Battery life heating season
Protection class IP20
Working temperature 0°C to +40°C