Elite Screens ZPM-RT User manual

Rev.081116-MZ
Remote Control Kit for Spectrum2 Series
What’s included:
ZPM-
RT Installation & Control Instructions 1
1. Disconnect the 3 Way
Control
3 Way Control Switch
B.RF Remotex 1pc A.IR Remote x 1pc
Red+ Green
C. 12V Trigger
1
ZPM-RT
Remote Control Kit for Spectrum2 Series
User Guide
RT Installation & Control Instructions 1
Control
Switch from the PowerMax Screen as shown below.
3 Way Control Switch
Red+ Green
-
F. Wall Box x 1pc
C. 12V Trigger
x 1pc
51”
D. IR eye receiver x 1pc
67”-95”
www.elitescreens.com
Remote Control Kit for Spectrum2 Series
Switch from the PowerMax Screen as shown below.
Screen
G. AAA batteries x 4pcs
H. Wireless 5-12v (3.5 mm)
mono trigger cable x 1pc

Rev.081116-MZ 2 www.elitescreens.com
2. Connect the Wall Box (G) to the screen as shown below.
Wall box (F) Screen
ZPM-RT Installation & Control Instructions 2
Please consult a professonial installer for this procedure. Elite Screens is not responsible for faulty installations.
1. Cut the cable of both the Wall Box (G) and the attached Control Switch to expose the wires.
Cut Cable
Cut Cable
Wall Box (F)
2. Connect the wires from the screen to the Wall box (F) according to their specific color.
Purple Wire = Up
Orange Wire = Down
Yellow Wire = Common
Yellow & Green Wire = Ground
Purple Wire = Up
Orange Wire = Down
Yellow Wire = Common
Yellow & Green Wire = Ground

Rev.081116-MZ 3 www.elitescreens.com
3. The Wall Box (F) should be connected to your screen as shown below.
IR Eye Receiver (Item, D)
Connect the IR Eye Receiver (D) to the Wall Box (F) for high wall or ceiling installations
Wall Box (F)
IR Remote (A)
IR Eye Receiver (D)
Wall Box (F
)
6 ways to control your screen:
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of sight
contact with a beam range of 30 feet. Aim the IR remote at the circular window located
on the left side of the screen
2. IR “Eye” Receiver (Item D, Fig 2): The IR “Eye” Receiver plugs directly into the
wall box’s RJ-45 input port.
3. RF Remote Control (Item B, Fig 1): The radio waves eliminate the need for a direct
line of sight with a range of 100 feet.
4. 3-Way Wall Switch: This accessory is not included but can be purchased separately
to use as a manual keypad switch to control the UP/STOP/DOWN functions of the
screen. It connects to the RJ45 port of the wall box.
Part number ZSP-WB-W
UPSTO
PDOW
N
Fig.1
IR/RF remote
Fig.2

Rev.081116-MZ 4 www.elitescreens.com
12 Volt Trigger (Item, C)
Connect the 12 Volt Trigger (C) to the Wall Box (F)for set up to your projector.
Wall Box (F)
12 Volt Trigger (C)
Red Wire +
DC12V
Green Wire -
0V Connect to Projector
Wireless 5-12v mono trigger cable (H)
5.
5-12 volt trigger
(Item C, Fig 4)
:
The built-in 5-12V trigger input allows your screen to synchronize its
drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will
retract when the projector powers down. The 5-12 volt RJ45 cable connects to your projector’s trigger output
via a separate cable that may or may not be provided by the manufacturer of the projector. The trigger
feature will not work without an output cable from the projector, but it can be tested by connecting the Red
(+) and Green (-) cable to a 9-volt battery.
6.
Wireless 5
-
12 volt trigger
(Item F, Fig 5):
The RF
remote control serves as a dual purpose, independently
as a handheld remote control, or in conjunction with the
Wireless 5-12 volt trigger cable. The radio frequency
technology can be programmed to send a wireless
signal to synchronize its drop/rise with the projector’s
power cycle.
Fig.4
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to
control your screen with your projector’s power cycle. Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30seconds for
full off and on cycle each time)
For a local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
DC
5
-
12V
The back of the
projector
Wireless5-12V trigger cable
UP
Stop
D
o
wn
Fig 5
5
-
12 Volt Trigger Cable