EliteProAV WhiteBoardScreen TE Series User manual

06242020 www.eliteproav.com U-00183 1
WhiteBoardScreen TE Series
Matte White Dry-Erase Whiteboard
Projector Screen
Model# WB4x8W2
User’s Guide
Thank you for choosing the WhiteBoardScreen TE (Thin Edge) Series dry-erase whiteboard projection screen!
The VersaWhite model can be used with tabletop or ceiling mounted standard, short, and ultra-short throw
projectors in a light controlled environment.
In addition to being a projector screen, it double as a dry-erase whiteboard that is scratch-resistant and easy to
clean. Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a
long product life.
Precautionary Notes:
Before using the dry-erase function of your whiteboard screen, please make note of the following instructions to
properly maintain and clean your dry-erase surface projection screen. These Whiteboard cleaning tips are just
as relevant with any dry-erase writing surface as they are with our Whiteboard- Projection Screens.
1. Only use a high-density foam eraser when removing dry-erase markings from the WhiteBoardScreen.
2. Do not use abrasive erasers as these may scratch the surface of the screen and will not erase dry-erase pen
markings on the whiteboard screen surface.
3. Never spray the whiteboard cleaning solution onto the surface while marker writing is present and then attempt
to use a high density foam eraser to remove. This will only smear the dry-erase marker ink making the surface
more difficult to clean and will likely ruin the foam eraser.
4. If there are any dry-erase markings left behind even after attempting to remove them using our high density
erasers, spray our whiteboard cleaning solution directly onto the screen surface anduse only a soft microfiber cloth
to wipe-down and clean the area.

06242020 www.eliteproav.com U-00183 2
Hardware and Parts
a. Wall Screws x 10
b. Hollow Wall Anchors x 10
c. Top Hanging Brackets x 2
d. Bottom Hanging Brackets x 2
e. Eraser x 1
f. Dry-erase markers x 2
g. Cleaning Solution x 1
h. White foam x 1
j. Tray hanging brackets x 2
k. Tray x 1
If replacement cleaning accessories are needed, please visit the Whiteboard cleaning accessories section of our
website at http://www.elitescreens.com/clean-whiteboard
Installation
Step1: Mark the location the WhiteBoardScreen will be installed and drill your holes for all of the Top Hanging
Brackets (c). Once the holes have been drilled, insert and screw the wall screws (a) as shown below. It is strongly
recommended to install the WhiteBoardScreen on wood studs for added stability. If the location does not have
wood studs, then use the included hollow wall anchors (b).
Step 2: Hang the WhiteBoardScreen on the Top Hanging Brackets,
making sure the top lip inserts into the rail on back of the frame.
Step 3: Next, attach the Bottom Hanging Brackets (d) to the bottom
frame, again making sure the lip of the bracket inserts in the rail. Then,
drill holes according to theholes on the bottom brackets to insert and screw
the wall screws to secure the bottom hanging brackets to the wall.
Model/Size
X1 = Bracket hole distance
X = Wall bracket distance
WB4x8W2
30mm (1.18”)
1200mm (47.24”)

06242020 www.eliteproav.com U-00183 3
Pen Tray Installation
Step 4: Line up the Tray Hanging Brackets (j) with the bottom screw holes of the bottom hanging brackets (b).
Then, mark and drill the holes and install brackets to the wall.
Minimum clearance requirement for pen tray installation diagram
Leave a minimum (of .46”/11.75 mm) between the top of the
pen tray bracket and the bottom of the whiteboard edge to
allow the pen tray enough room to attach to the bracket.

06242020 www.eliteproav.com U-00183 4
Step 5: Attach the pen tray on the tray hanging bracket as shown in the steps below.
Step 6: Use the M4 screws (i) to lock and secure the pen tray to the brackets.
For a local Elite ProAV contact or Technical Support, please visit
www.eliteproav.com