EliteProAV Pro Frame Acoustic Series User manual

01032020JA 1www.elilteproav.com
Pro Frame Acoustic Series
Acoustically Transparent Fixed Frame Projection Screen
User’s Guide
Hardware and Parts List
1. Frame Parts x 6 pcs
(4 top/bottom frame pcs. + 2 side frame pcs)
8. Wood Screws x 8pc and Drywall anchors x 8pcs
2. Tension Rods x 6 pcs
(4 top/bottom rods + 2 side rods)
9. M5x15 Screws x 16 pcs
3. Screen Material x 1 pc
10. Center Support Bar x 1-2 pcs
(depending on model/size)
4. Black backing material x 1 pc
11. Support joiner x 2-4 pcs (depending on model/size)
5. Center joints x 2 pcs
12. Fix Plates x 30-90 pcs (depending on model/size)
6. Elbow Joints x 4pcs
13. Rubber hammer (mallet) x 1 pc
7. Wall brackets x 2-4pcs
14. Screw driver x 1 pc
Note: Please make sure all parts are included in your package before proceeding to assemble your fixed
frame projection screen.
Frame Assembly
1. Insert the center joint connector to the
horizontal frame piece and then fasten it with
2screws.
2. Insert the other horizontal frame piece to the center joint connector and then fasten it with 2 screws.
Make sure the frame piece lines up correctly before you tighten the screws completely.
1/2Long frame
Push

01032020JA 2www.elilteproav.com
Push Push
Short frame
Short frame
3. Insert both elbow joint connectors into the long horizontal frame (fig.1).
Push Push
Joint
Long frame
( fig.1)
Screw
( fig.3)
M5x15 Screws
M5x15 Screws
(Fig.1.1)
(Fig.1.2)

01032020JA 3www.elilteproav.com
Push Push
( fig.2)
Insert the exposed ends of the joint connectors
into the short (vertical) frame and align the four
corners so that they meet at perfect right angles
Tension Rod (Horizontal) x 4
Tension Rod (Vertical) x 2
4. Join all four frame parts together following the steps showed below. After making sure that all four corners join
at right angles to form a perfect rectangle, fasten the four angles together by using the (x8) joint screws included
(fig.2).
ATTACHING THE SCREEN MATERIAL TO THE FRAME_
1. Unroll the screen material and lay it down on a clean surface. Then insert the tension rods separately into the
edges of all four corners of the material (see fig.3)
2. Make sure the screen material and frame are both lying face down on a clean, dry, and non-abrasive surface.
3. Carefully unroll the material inside the frame. (Fig.4)
Tension Rod (Horizontal) x 4
push
Tension Rod (Vertical) x 2
(Fig. 3)
Screen Material
Screen Material
push
push
push
push
push
M5×15 screws
Screw
( fig.3)

01032020JA 4www.elilteproav.com
Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a
sufficient amount of tension for perfect material flatness.
4. Attach the fix plates.
(1) Stretch the material to the corner and insert the screen material’s edge in the groove of the frame. While
one hand holds the material in place the other hand snaps in the push plate (Fig.5-Fig.6).
(2) Begin by securing the four corners in the following sequence A→B→C→D (Fig.7).
(3) Insert the fix the plates as shown on Fig. 5. Fix plate ① is about 10cm away from the frame’s corner.
Fix plate ② is about 5cm away. (Fig.8)
(Fig. 7)
Notes：
•Make note of the label to help distinguish the
back and front side.
•Unroll the screen material face down
•Keep the screen material as close as possible to
the frame and do not allow it to scratch against
any part of the frame.
A
B
C
D
(Fig. 8)
(Fig. 5)
Insert push plate in
Screen material edge
(Fig. 6)
Schematic cross section
of the frame
Plate
Frame groove
(Fig.4)

01032020JA 5www.elilteproav.com
(4) Place a fix plate in the center of each side in the following order E→F→G→H (Fig.10).
(5) Next, fasten a fix plate on the center of each frame side in the following order I→J→K→L→M→N→O→P
as shown in Fig.11.
(6) Fasten the remainder of the fix plates in the empty locations in the red markings to complete attaching the screen
material. (Fig.12)
Tip for attaching the last corner (D):
1. Position yourself left of location ①.
2. Pull the material to the corner of the frame with your hand while your
left hand snaps in the fix plate on location ①
3. Then insert and snap in the fix plate on location②.
4. Next, move and position yourself on location ③，then pull the edge to
the frame and fasten plates on locations③and④.
5. Finally, fasten the last fix plate on location⑤. (Fig.9)
①
②
③
⑤
④
Pull
(Fig. 9)
E
G
H
F
(Fig.10)
(Fig.12)
I
J
K
L
M
N
O
P
(Fig.11)

01032020JA 6www.elilteproav.com
Black backing attachment procedure
The purpose of the black backing material is to block out any light penetration that may reflect off of anything
mounted behind the screen, which can cause distortion to the projected image.
Center Support Bard
1. Insert the support joiner (j) into each end of the center support bar (i).
support joiner
Center support bar
2. Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where the fix
plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an angle so that
both ends of the bar are in alignment with the groove (see Fig. 17and Fig. 18below for details).
Diagonal models 135” = 1 x Center Support Bar
Remove
push
Center Support Bar
Interval markings reveal the best points for inserting the fix plates
(Fig. 12). The prongs on the fix plates insert to the lip on the back of the
frame creating a friction hold that will firmly keep the material and
black backing in place (Fig. 13-14).After the material has been installed,
the backing will lay over the back of the white (Acoustic) material and
then be held in place by the Velcro on the fix plates (Fig 15).
(Fig. 13)
(Fig. 15)
(Fig. 14)
(Fig. 16)
The black backing is held in place by the Velcro that is on the fix plates.
Black backing
Fix plates secure the Acoustic material and the black backing behind it.
Screen material edge
Center Support Bar
(Fig. 17)
Fixed plate groove
(do not insert here)

01032020JA 7www.elilteproav.com
Diagonal models above 135” = 2x Center Support Bars
3. Slide the top end of the bar into the top center
point of the frame to complete the center support bar
installation. This will provide added stability to
your frame and added tension to the material.
Installation
1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole area of
where the screen is to be installed.
2. Drill a hole with the proper bit size according to the wood screws included.
3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a
Phillips screw driver. Note: Use 2 top wall brackets on diagonal sizes below 135”, and use 3 top wall
brackets on diagonal sizes 135” and above.
4. Position the fixed frame screen onto the top wall brackets as shown in (Fig. 19) and push down at the center
of the bottom frame to secure the installation.
5. The design of the wall brackets allows the frame to slide over them through its sides. This is an important
feature of the installation design as it allows your screen to be properly centered.
6. Using both hands finish the installation by pushing the lower portion of the fixed frame screen into the
lower bracket as shown in Fig 20.
(Fig. 18)
(Fig. 19)
(Fig.20)

01032020JA 8www.elilteproav.com
CAUTION
Please follow these instructions carefully to ensure proper maintenance and safety of your Fixed Frame Screen
1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture,
ladders, windows, etc. occupy the space designated for your fixed frame screen.
2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors are used
and that the weight is supported appropriately by a strong and structurally sound surface just as any large and heavy
picture frame should. (Please consult a home improvement specialist for the best advice on installation)
3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care.
4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any other
impurities.
5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen surface.
6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other sharp or
abrasive objects.
8. Spare Parts should be placed out of reach of small children in accordance with household safety guidelines.
For a local Elite Prime Vision contact or Technical Support, please
visit www.eliteproav.com