EliteProAV Saker Tab-Tension CineGrey 5D Series User manual

03282019JA 1 U-00140 www.eliteproav.com
Saker Tab-Tension
CineGrey 5D® Series
Ambient Light Rejecting Electric
Wall/Ceiling Projection Screen
User’s Guide
The projection screen material is our ISF certified CineGrey 5D® , which is a reference quality front
projection material precisely formulated for environments with minimal control over room lighting. It was
designed to enhance picture brightness, accurate color fidelity, and improve contrast levels. The CineGrey
5D® is best for family rooms, educational facilities, conference rooms or any applications in which incident
light is a factor.
In order for the CineGrey 5D® to maintain its projection qualities and optimum performance, please refer to
the list below for proper maintenance and cleaning.
Use a dry microfiber cloth to remove dust from the screen’s surface.
When cleaning, use a damp microfiber cloth with warm water to remove any marks.
Never rub or apply pressure when cleaning the surface.
Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils
or any other sharp or abrasive objects.
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be aware of this as it will void your warranty with Elite ProAV. Unapproved
changes or modifications (except for cutting the power cord for hardwire installations) to this unit are
prohibited and will void your warranty. For more information, please contact our Technical Support
Department at [phone] Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle.
Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short
circuit.
There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.
No one except authorized technicians can open and make repairs to this unit.

03282019JA 2 U-00140 www.eliteproav.com
Make sure the power source this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
Avoid direct Sunshine, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious
damage or if there are any evident broken parts.
WARNING
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop
in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite ProAV Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna of the device which may cause interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling
on the viewing surface will not cause the casing to become loose or fall. The installer must ensure that the
fasteners used are of adequate strength and suitable for the installation location. Included mounting screws are
complimentary and may not be appropriate for all mounting surfaces. Use appropriate anchors to safely secure
the screen to the mounting surface or consult with a professional installer.

03282019JA 3 U-00140 www.eliteproav.com
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from
the CineGrey 5D® Angular Reflective ALR (Ambient Light Rejecting) Screen.
•Angular-Reflective material is not compatible with ultra/short-throw projectors
•Minimum lens throw ratio 1.5x image width
•Ambient light must not come from the same direction as the projector
Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it is
important to position the projector so that the viewer will get the best possible image.
Step 1: Establish the general “eye level” of the viewers
Step 2: Set the appropriate projection level
Step 3: Adjust the screen height level and projection angle
Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

03282019JA 4 U-00140 www.eliteproav.com
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A. Wall/Ceiling
mount bracket
x2
B.
M5x60
Screw x6
C. M12
Dry-wall
anchor x6
D. Bracket
connector x2
(installed on
housing)
E. M5x11
Bolt
Screw x4
F. M5x25mm
round head
cross screws x2
G. M5x30mm
eyebolt screw
& M5 nut x2
H.
Snap
link x2
Installation Instructions
For installation assistance, please consult a professional Installer. Elite ProAV is not liable for faulty
installations. Two or more people are required while one holds the screen in place.
A. Wall Mount
Flush mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom
screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor(C), M5x60 screw (B), Make sure
both brackets are properly leveled.
3. Hang the screen by placing the downward “catch” located on the back over the brackets upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
B. Ceiling Mount
Ceiling Mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom
screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor(C), M5x60 screw (B), Make sure
both brackets are properly leveled.
3. Hang the screen by placing the downward “catch” located on the back over the brackets upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
Front view of bracket
(A)
Side view of bracket (A)
Wall
M5x25MM round
head cross screws
(F)
Front view of
bracket (A)
M5x25MM
round head
cross screws (F)
Ceiling

03282019JA 5 U-00140 www.eliteproav.com
II. Suspended
1. Screw the eyebolt (G) on the bracket connector (D).
2. Attach the snap link (H) through the eyebolt (G) and connect it to an eyebolt screw
(not included) rated for the screen’s weight.
Screen material tension adjustment
(4mm Allen Wrench required and not included)
Remove the weight bar end cap to expose the adjustment
tension knob. Insert your 4mm Allen Wrench to push in
the adjustment tension knob, turn clockwise and your
screen will gain more tension. Turn the Allen Wrench
counter clockwise and the screen will lose tension. Please
note this adjustment is not necessary as the tension of the
screen has been set to its factory setting for best
performance. Please contact EPV® for assistance to
avoid damaging the screen and voiding your warranty.
Saker Tab-Tension CineGrey 5D® Series | Controls and Accessories
A. IR
Remote
B. RF
Remote
C. Wall
switch
control box
D. 5-12 volt
trigger
cable
E. IR
extended
“eye” receiver
F. Wireless 5-
12v trigger
cable
G. AAA
batteries
H. Bubble
Leveler
Screen operation
Electric Current: Depending upon region, your screen will operate on 100v, 110v, or 220v voltage.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Saker Tab-Tension
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of
sight contact with a beam range of 30 feet. Aim the IR remote at the circular
window located on the left side of the screen.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs directly
into the screen’s RJ-45 input to present a low profile line-of-sight control option
for your IR remote control even in a recessed ceiling installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a direct
line of sight with a range of 100 feet.

03282019JA 6 U-00140 www.eliteproav.com
UP
Stop
Down
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to
control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30seconds
for full off and on cycle each time)
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V trigger
input allows your screen to synchronize its drop & rise with the
projector’s power cycle. The screen deploys when the projector
powers up and will retract when the projector powers down. The
5-12 volt RJ45 cable connects to your projector’s trigger output
via a separate cable that may or may not be provided by the
manufacturer of the projector. The trigger feature will not work
without an output cable from the projector, but it can be tested by
connecting the Red (+) and Green (-) cable to a 9-volt battery.
Fig.3
Fig.2
IR “eye” receiver
3 Way Wall Switch
(does not have IR sensor)
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall mount control box with an
up/stop/down button and plugs directly into the screen’s RJ-45 input.
For more information, technical
support or your local Elite
ProAV® contact, please visit
www.eliteproav.com
DC 5-12V out
Wireless 5-12V
trigger cable
The back of the
projector
Fig 5
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote
control serves as a dual purpose, independently as a handheld
remote control, or in conjunction with the Wireless 5-12 volt
trigger cable. The radio frequency technology can be
programmed to send a wireless signal to synchronize its drop &
rise with the projector’s power cycle.