Elite Screens ITE139XW3-E8 User manual

Rev.071916-MZ 1 www.elitescreens.com
In-Ceiling Electric Motorized Front Projection Screen
Evanesce Tab-Tension Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
•The power outlet supplying power to the unit should be close to the unit and easily accessible.
•Do not install the unit on uneven, inclined surfaces;
•Do not install in damp places to avoid an electric shock or short circuit.
•Do not place any heavy objects over the power cord.
•Position the power cord properly to avoid creating a trip obstacle.
•To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the
power cord.
•The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and make
repairs to this unit.
•Make sure the power source that this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid over heat.
•Do not handle the power plug when your hands are wet or your feet are in contact with water.
•Properly dispose of this equipment according to the environmental regulations in your area
when product is no longer of service.

Rev.071916-MZ 2 www.elitescreens.com
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
•Avoid direct sun light, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from overheating.
•Cut off the power supply first before transportation or maintenance.
•To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is
obvious damage or if there are any evident broken parts.
Installation Warning
The instructions provided in this user’s guide are for reference only. Please consult a
professional installation company for further installation and safety advice. The installer must
insure that proper mounting hardware is used to provide adequate strength suitable for the
installation. Elite Screens is not liable for any faulty installations. For limit adjustment instructions,
please contact our Technical Support Department at [phone] Ext. 604
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
✓Reorient or relocate the receiving antenna of the device which may be casing the
interference.
✓Increase the separation between the screen and the device’s receiver.
✓Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
the fasteners that are used are of adequate strength and suitable for the installation location.

Rev.071916-MZ 3 www.elitescreens.com
Evanesce Tab-Tension Series| Controls and Accessories
A. IR Remote
B. RF Remote
C. Wall switch control box
D. 5-12 volt trigger cable
E. IR extended “eye” receiver
F. Wireless 5-12v (3.5 mm)
mono trigger cable
G. AAA batteries
H. Bubble leveler
Screen operation
Electric Current: Depending upon region, your Elite Screen will operate on 100v, 110v, or 220v voltage.
1.After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the poweroutlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Evanesce Tab-Tension
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line
of sight contact with a beam range of 30 feet. Aim the IR remote at the
“eye” receiver once it has been connected to the control box’s RJ45 port.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs
directly into the control box’s RJ45 port to present a low profile line-of-
sight control option for your IR remote control even in a recessed ceiling
installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a
direct line of sight with a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall
mount switch with an up/stop/down button and plugs directly into the
control box’s RJ45 port.
Fig.3
UP
STOP
DOWN
Fig.1
IR/RF remote
IR “eye” receiver
Fig.2
3 Way Wall Switch
(does not have IR sensor)
Control box
Control box

Rev.071916-MZ 4 www.elitescreens.com
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF
remote control serves as a dual purpose, independently as
a handheld remote control, or in conjunction with the
Wireless 5-12 volt trigger cable. The radio frequency
technology can be programmed to send a wireless signal to
synchronize its drop/rise with the projector’s power cycle.
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and
able to control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
Hardware Parts List for EvanesceTab-Tension Series
Please make sure all parts listed below are included before proceeding with the installation.
Hardware Parts List
QTY
A. Case Rail Nut
4-6
B. Hex Screw
4-6
C. Hanging Bracket
2-3
D. Suspension Bar
4
E. Washer
8-10
F. Hex Nut
4-6
G. Suspension Bar J- Hook
4
H. M8 Top Expanding Bolt
4
I. M8 Threaded Rod
4
J. M8 Screw Nut
20
K. M8 Hexagonal Screw
4
L. M8 Screw Washer
28
M. Installation Bracket
2
N. Socket Wrench
1
O. White cover flange panel
2
DC 5-12V
out
The back ofthe
projector
Wireless 5-12V trigger cable
UP
Stop
Down
Fig 5
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V
trigger input allows your screen to synchronize its drop &
rise with the projector’s power cycle. The screen deploys
when the projector powers up and will retract when the
projector powers down. The 5-12 volt RJ45 cable connects
to your projector’s trigger output via a separate cable that
may or may not be provided by the manufacturer of the
projector. The trigger feature will not work without an
output cable from the projector, but it can be tested by
connecting the Red (+) and Green (-) cable to a 9-volt
battery.
RJ45 Input
5-12 volt trigger cable
Fig.4
H
I
J
K
L
M
N
O
G

Rev.071916-MZ 5 www.elitescreens.com
Installation Instructions
The Evanesce Tab-Tension allows access for above or below ceiling installation. Please follow the
instructions described in the following steps below for your type of installation.
Power
The Evanesce Tab-Tension B Series includes a 3-
Prong Power Cord (2-Prong Power Cord for some
countries) for use in a non-concealed power outlet.
If your installation will be entirely concealed
(including power outlet), Elite Screens strongly
recommends a hardwire connection. Please refer
to the image below for both 110v & 220v wiring
information.
A. Above ceiling installation instructions
Assembly
1. Insert the Hex Screw (B) through the Hanging Bracket’s (C) screw hole and secure with the Case
Rail Nut (A). Slide the Hanging Bracket (C) through the railing on top of the case.
2. Place the Suspension Bar (D) on the Hanging Bracket (C) and align with the hole as shown below.
Secure the Suspension Bar (D) with the Hex Screw (B), Washer (E) and the Hex Nut (F). Install
the Suspension Bars (D) to your ceiling according to their distance.
D
B
E
E
F

Rev.071916-MZ 6 www.elitescreens.com
Optional Suspension Bar J-Hook (G)
1. Attach the Suspension Bar J- Hook (G) to the bottom of the Suspension Bar (D) and secure with
the Hex Screw (B), Washer (E) and Hex Nut (F).
2. Attach the Suspension Bar J-Hook (G)to the Hanging Bracket (C) as shown in figure below.
Install the Suspension Bars (D) to your ceiling according to their distance.
Optional Installation (parts & hardware not included)
1. Place the Hanging Bracket (C) in the desired location on the screen’s housing and measure the
distance as shown below. (L = Distance)
B
E
E
F
G
C

Rev.071916-MZ 7 www.elitescreens.com
Ceiling
Ceiling Panel
Ceiling installation space
The ceiling truss
2. Mark the location of where the screen will be installed according to the distance (L) and then
secure the bolt to the ceiling.
3. Install the screen to the screw bolt as shown in the figure below.
B. Below ceiling installation instructions
1. Measure and cut the ceiling installation space. The width should not exceed 120mm. Please refer
to the length on the screen size table (C3).
Note: The length of the installation space is not greater than the screen size table (C3), and the width
is not less than the screen size table (A5). Consult the table below (C1) in regards to accommodating
the screen casing.

Rev.071916-MZ 8 www.elitescreens.com
(N)
(K)
(H)
The ceiling wall
Install screw holes
2. Drill 4 holes in the ceiling that correspond with the attachments on the various casing sizes.
3. The expanding bolts (H) mount into thick wood beams, stone or concrete and will support the
screen. Use the Socket wrench (N) to attach the hexagonal screws (K). The expanding bolts
should be firmly tightened and tested to make sure that they will hold the weight of the screen.
Ceiling
(J) and (L)
(I)
(K)
(M)

Rev.071916-MZ 9 www.elitescreens.com
4. Push the screen up into the space. Use the threaded rods (I) to attach the screen assembly to the
ceiling. The hexagonal screws (K) will connect the screen to the rest of the assembly.Once firmly
in place, use the nuts (J) to ensure a firm connection. Use thesocket wrench (N) to make sure that
the bolts are firmly tightened.
5. Install plastic cover panel (O) to complete the installation.
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Ceiling
Socket wrench (H)
Push