Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL User manual

Instruction Book for
TENSIONED LARGE COSMOPOLITAN®
ELECTROL®
The Da-Lite Difference.
DA-LITE SCREEN COMPANY LLC
3100 North Detroit Street
Post Office Box 137
Warsaw, IN 46581-0137 USA
P 800-622-3737 / 574-267-8101
F 877-325-4832 / 574-267-7804
www.da-lite.com
e-mail: [email protected]

IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should
always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of fire, electric shock, or injury to
persons.
SAVE THESE INSTRUCTIONS
1

Carefully unpack screen and remove outer wrapping from case.
The slat retainer screws must be removed before installation. Use supplied 1/8" nex key to remove silver shipping
brackets attached to slat and screen case. Orient the case with the slat down and then remove the screws. The case
must remain in that orientation throughout the installation process to avoid fabric damage.
The Tensioned Large Cosmopolitan®Electrol®comes with brackets to allow for wall mount or ceiling mount installations.
Procedures for each method are as follows:
INSTALLATION
2
CASE HOOK
VIEWING SURFACE
(AUDIENCE SIDE)
FIGURE 2
FIGURE 1
2"
VIEWING SURFACE
(AUDIENCE SIDE)
CASE HOOK
WALL
MOUNT
BRACKET
STOP SCREW
CEILING
MOUNT
BRACKET
5/16x3/4"
BOLT, NUT
AND LOCK
WASHER
WALL MOUNT
BRACKET
STOP SCREW
1-1/8"
Wall Mount
1. The wall mount bracket should be fastened to wall
studs or some reinforcement within the wall. Concrete
or brick walls require special fasteners and anchors.
2. The wall bracket has holes spaced at 16" and 24" to
align with most wall studs.
3. The bracket must be level and plumb.
4. Keep in mind you will need at least 2-3/4" between the
ceiling and the top of the wall mount bracket to be
able to position the case on the bracket.
5. Mount the screen case on the wall bracket as shown
in figure 1. Be sure the case is fully seated on the
bracket. Tighten the stop screws against the wall
bracket.
Ceiling Mount
1. Be sure the ceiling has adequate reinforcement to
attach the screen brackets.
2. Attach the ceiling brackets to the wall mount bracket
using the supplied 5/16" x 3/4" bolts, washers and
nuts.
3. Position the ceiling bracket assembly on the ceiling
and attach with 5/16" bolts (not supplied). The bolts
should be long enough to pass through the drywall or
ceiling tile and penetrate at least 1-1/2" into the
reinforcement in the ceiling.
4. Mount the screen on the wall bracket as shown in
figure 2. Be sure the case is fully seated on the
bracket. Tighten the stop screws against the wall
bracket.
Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory.
No further adjustment is necessary.
SCREEN AdjUSTMENT
CONTACT DA-LITE AT 800-622-3737 OR 574-267-8101 IF SCREEN MOTOR NEEDS ADjUSTMENT.
s
!

TENSIONEd LARGE COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITHOUT A BUILT-IN LOW
VOLTAGE CONTROL
Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box
located on the left end of the screen case.
See wiring diagram below for wire connections.
NOTE: This screen can only be controlled by a single 120VAC or 240VAC wall switch. To use multiple switches, an optional low
voltage control must be used.
3
240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH:
Da-Lite offers two styles of 240 volt wall switches for standard operation.
Please see wiring diagram in wall switch boxes included with screen.
UP
OFF
DOWN
THIS SWITCH CAN NOT
BE USED WITH LVC.
120V WIRING DIAGRAM FOR
STANDARD WALL SWITCH
SPDT SWITCH WITH
CENTER OFF
AC (COMMON)
AC HOT 120VAC 60HZ 1 AMP
BLACK/YELLOW
BLACK
RED
WHITE RED (UP) BLACK (DOWN)
JUNCTION BOX
LOCATED IN
LEFT ENDCAP WHITE
RED
BLACK
GREEN
MOTOR
NOTE: A SINGLE SWITCH CANNOT BE
USED TO OPERATE MORE THAN
ONE SCREEN. CONTACT THE
FACTORY FOR FURTHER
INFORMATION.

4
TENSIONEd LARGE COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITH A BUILT-IN LOW
VOLTAGE CONTROL
LOW-VOLTAGE WALL SWITCH
OPTIONAL IR AND RF
REMOTE CONTROL
MOTOR
BLUE (COMMON)
BROWN (HOT)
GREEN
GROUND TO CASE
240VAC 50HZ
240V WIRING DIAGRAM
WITH OPTIONAL BUILT-IN
LOW VOLTAGE CONTROL
Rj9
UP
STOP
DOWN
GROUND–MUST BE
CONNECTED TO
BUILDING GROUND
Rj9
GREEN
FRONT BACK
UP DN GND +5V
3-POSITION
SWITCH Rj9
ILT Rj9 PIN-OUTS
(TAB IS FACING UP)
IR or UP BLACK
GND COMMON RED
+5V GREEN
DN or DATA WHITE
DRY CONTACTS
SPLITTER
UP +5V COM DN
IMPORTANT NOTE: The wall switch is REQUIRED to make any limit
switch adjustments, EVEN if a third party control
system is used. Therefore, it is advised to wire
the switch or provide a 4-conductor connection
that is accessible.
120V WIRING DIAGRAM
WITH OPTIONAL BUILT-IN
LOW VOLTAGE CONTROL
GROUND–MUST BE
CONNECTED TO
BUILDING GROUND
Rj-14 PIN-OUTS
(TAB IS FACING UP)
IMPORTANT NOTE:
The wall switch is REQUIRED to make any limit switch
adjustments, EVEN if a third party control system is
used. Therefore, it is advised to wire the switch or
provide a 3-conductor connection that is accessible.
UP
STOP
DOWN
POWER INPUT 120VAC / 60HZ
GREEN (GROUND)
BLACK (HOT)
WHITE (COMMON)
POWER WIRE
DATA
CABLE
Rj-45 jACK
Rj-45
RECEPTACLE
Rj-22
OUTPUT
Rj-22
jACK
Rj-22
INPUTS
Rj-22
jACK
LED
UP LIMIT
TACTILE
BUTTON
DOWN LIMIT
TACTILE
BUTTON
FRONT OF
WALL SWITCH
BACK OF
WALL SWITCH
Rj-22 PIN-OUTS
(TAB IS FACING UP)
Rj-45 PIN-OUTS
(TAB IS FACING UP)
Standard Rj-22 can be used in place of Rj-14Supplied Rj-14 cable
BLUE
YELLOW
GREEN
RED
BLACK
WHITE
+12V
BUS (RP DATA)
RQ DATA
+5V
GND
RQ CLOCK
BUS (RP DATA)
RQ DATA
+5V
GND
WHITE
GREEN
RED
BLACK
BLUE
YELLOW
GREEN
RED
BLACK
ORANGE
BROWN
PURPLE
+12V
BUS (RP DATA)
RQ DATA
+5V
GND
RQ CLOCK
MANUAL 1
MANUAL 2
DRY CONTACTS
UP
DOWN
COMMON
BUS
5V BUS
BUS
COM
5V
BUS
3-conductor 20-24 gauge wire can be used in place of
the supplied RJ-14 cable to connect the wall switch.
Connect the BUS terminals on the wall switch to the
corresponding BUS terminals on the splitter board.

5
TROUBLESHOOTING
SYMPTOM
1. Screen will not operate.
Motor does not hum.
2. Incorrect stopping position in
downward direction.
3. Incorrect stopping position in
upward direction.
4. Noise.
NOTE: Screen will operate with a
low pitched hum.
5. Coasting.
CAUSE
(a) Blown fuse.
(b) Tripped circuit breaker.
(c) No power to operating switch
or junction.
Power at junction box
(d) Thermal overload tripped.
(e) Broken wire in the “down” or “up”
position.
(f) Defective motor, limit switch or
capacitor.
(g) Capacitor burned out.
(a) Lost roller wrap.
(b) “Down” limit switch out of
adjustment
(a) Lost roller wrap.
(b) “Up” limit switch out of
adjustment
(a) Gear Noise.
(a) Defective brake.
SOLUTION
(a) Replace fuse.
(b) Reset circuit breaker.
(c) Check above. Tighten all loose
wire connections. Correct any
improper connections.
“Down” Position
Check for power across black
and white leads.
“Up” Position
Check for power across red
and white leads.
(d) Let motor cool down for 15
minutes. Try again.
(e) Check for continuity. Cut off old
splice and reconnect.
(f) Replace motor assembly.
NOTE: Motor is a sealed assembly.
(g) Replace motor assembly.
(a) See instructions below.
(b) Contact Da-Lite at 800-622-3737
or 574-267-8101
(a) See instructions below.
(b) Contact Da-Lite at 800-622-3737
or 574-267-8101
(a) Replace motor assembly.
(a) Replace motor assembly.
Visit www.da-lite.com/products/product_videos.php to find installation and troubleshooting videos and
tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at
[email protected] or by phone at [phone] or [phone] with any troubleshooting questions.

6
THIS PAGE IS INTENTIONALLY LEFT BLANK

LIMITED ONE YEAR WARRANTY
ON DA-LITE PRESENTATION PRODUCTS
Da-Lite Screen Company LLC warrants its products to the original purchaser only, to be free from
defects in materials and workmanship for a period of one (1) year from the date of purchase by
the original purchaser provided they are properly operated according to Da-Lite’s instructions and
are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental
damage, or which has been tampered with or repaired by a person other than authorized Da-Lite
personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)
the defective part of the merchandise. Returns for service should be made to your Da-Lite
dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation
expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for
damage in shipment. To protect yourself against damage or loss in transit, insure the product and
prepay all transportation expenses.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any
implied warranties of fitness for use, or merchantability, that may be mandated by statute or
rule of law are limited to the one (1) year warranty period. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state-to-state. NO LIABILITY
IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN
OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL
DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may
contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, [phone], (800) 622-
3737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE
BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH
DA-LITE’S WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
Printed in U.S.A. 98770 Rev. 3/13
7