EliteProAV CLR Series User manual

07212020JA 1 www.eliteproav.com
Saker Tab-Tension CLR® Series
Ceiling Ambient Light Rejecting Electric
Wall/Ceiling Projection Screen
User’s Guide
____________________________________________________________________________________________
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop limit. There is NO extra black-matte
drop material on the roller. Please be aware that altering the vertical limit switch to drop the screen material off the
roller voids your warranty with EliteProAV. Unapproved changes or modifications (except for cutting the power
cord for hardwire installations) to this unit are prohibited and will likewise void your warranty.
For more information, please contact our Technical Support Department at [phone] Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, make sure the power connection is secure.
The power source should be close to the unit and easily accessible.
Do not install the unit on uneven, or inclined surfaces.
To avoid electrical shock or product damage, do not install this device in a damp place.
Do not place any heavy objects over the power cord.
Position the power cord properly to avoid creating a trip hazard.
Avoid electrical shock or fire, by not overloading the power cord.
The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble this
unit by yourself. Consult an authorized technician instead.
Make sure the power source that this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure said cord has a compatible power rating.
Do not handle this or any other electrical device if you are wet or standing in water.
Whenever the screen reaches its end of life, follow local environmental guidelines regarding its proper
disposal.
Do not use this unit under the following circumstances.
Disconnect the power cord if exposed to moisture, rain, wind, electrical storms or snow.
Avoid exposure to direct sunlight or any of the conditions stated in the previous bullet point.
Keep away from fire or other high temperature heat sources.
Cut off the power supply first before attempting maintenance or removal.
Do not attempt to use this screen if there are obvious signs of damage.
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious
damage or if there are any evident broken parts.
WARNING
Individual modifications to this product are prohibited and will void the manufacturer’s warranty. Please contact
the EliteProAV Customer Service Team with any questions.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.

07212020JA 2 www.eliteproav.com
The product settings are designed to provide reasonable protection against any radio interference within a
residential installation. If properly installed, the Saker Tab-Tension screen may suffer from RF interference from
other home electronics.
Although radio interference affecting other household electronics is unlikely, the following steps can be taken
should RF interference occur.
Reorient or relocate the receiving antenna on the device that may be casing the interference.
Increase the distance between the screen and the interfering device’s receiver.
Connect the projection screen to another power source apart from the interfering device.
SCREEN MAINTAINANCE
Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection
image. For optimal results we advise to pay attention to the following instructions.
1) The screen surface has a horizontal linear structure. DO NOT wipe the screen up and down or in a circular
motion. Wipe gently from left to right only.
2) Clean the dust on the screen surface with a soft brush or microfiber cloth. A rough/coarse towel or cloth may
damage the screen’s surface.
3) Gently wipe the screen with a lightly moistened white lint free cloth with water or with a neutral detergent
(1mL/0.33 oz) mixed with water (1000 mL/33.8 oz).
Notes：The following precautions should be followed to avoid damaging the material, which is not
covered under warranty.
Don’t touch the screen material to avoid leaving fingerprints.
Use gloves when handling the material.
Don’t scratch the material, as it will leave permanent markings on the screen’s surface.
Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the material.
Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using
such chemicals will permanently damage the screen.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen upright on a clean, level surface.
3. Keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, each screen should be securely installed so that vibrations or pulling on the
viewing surface will not cause the casing to become loose or fall. Included are complimentary mounting screws
that may or may not be appropriate for the installation you are attempting. Always use the correct anchors to
safely secure the screen. This product is for professional integrators only.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A.
Wall/Ceiling
mount bracket
x2
B. M5x60
Screw x6
C. M12
Dry-wall
anchor x6
D. Bracket
connector x2
(Installed on the
housing)
E. M5x11
Bolt Screw x4
(Attached to
Part D)
F. M5x25MM
round head
cross screws x2
G. M5x30MM
eyebolt screw
& M5 nut x2
H. Carabiner x 2

07212020JA 3 www.eliteproav.com
Notice to Installer:
Proper Projector Placement for CLR®
The CLR® is exclusively for table-mounted ultra-short throw projectors as illustrated in example 1 below.
Overhead placement or a standard projector will make the image very dark, on account of the screen’s absorbent
layer deflecting light that is not aligned with its reflective angle.
Example 1: Proper Projector Installation
Example 2: Improper Projector Installation
Images are not up to scale and are for illustrations purposes only.

07212020JA 4 www.eliteproav.com
Installation Instructions
A. Wall Mount
Flush hidden mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and
bottom screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked points and install the brackets with the dry-wall anchor(C), M5x60 screw (B),
Make sure both brackets are properly leveled.
3. Hang the screen by placing the lower “catch” located on the back over the brackets upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
Two or more people are required while one holds the screen in place.
B. Ceiling Mount
I. Ceiling Mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and
bottom screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor(C), M5x60 screw (B),
Make sure both brackets are properly leveled.
3. Hang the screen by placing the lower “catch” located on the back over the bracket’s upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen
Two or more people are required while one holds the screen in place.
II. Suspended
1. Screw the eyebolt (G) on
the bracket connector (D).
2. Attach the snap link (H)
through the eyebolt (G) and
connect it to an eyebolt
screw (not included) rated
for the screen’s weight.
Front view
of bracket
(A)
Side view of
bracket (A)
M5x25MM
round head
cross screws (F)
Ceiling
Front view of bracket (A)
Side view of bracket (A)
Wall
M5x25MM round
head cross screws
(F)
Ceiling

07212020JA 5 www.eliteproav.com
Screen material tension adjustment
(4mm Allen Wrench required and not included)
Remove the weight bar end cap to expose the adjustment
tension knob. This knob has a 4mm Allen port. Insert your 4mm
Allen Wrench and push in the adjustment tension knob, turn
clockwise and your screen will gain more tension. Turn the
Allen Wrench counterclockwise and the screen will lose tension.
Please note this adjustment is not necessary as the tension of the
screen has been pre-set to its factory drop setting. If you would
like to adjust the screen tension, please contact EliteProAV™
for assistance to avoid damaging the screen and voiding your
warranty.
Saker Tab-Tension DarkStar UST Series | Controls and Accessories
A. IR
Remote
B. RF
Remote
C. Wall
switch
control box
D. 5-12-volt
trigger cable
E. IR
extended
“eye” receiver
F. Wireless
5-12v trigger
cable
G. AAA
batteries
H. Bubble leveler
Screen operation
Electric Current: Depending upon region, your Elite ProAV Screen will operation 110v, or 220v voltage.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Saker
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of sight contact using
a beam range of 30 feet. Aim the IR remote at the circular window located on the left
side of the screen.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs directly into the
screen’s RJ-45 input to present a low-profile line-of-sight control option for your IR
remote control. It is an extended eye-receiver to accommodate a recessed ceiling
installation
3. RF Remote Control (Item B): The radio waves eliminate the need for a direct line
of sight and has a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall mounted
control box with an up/stop/down button. It plugs directly into the screen’s RJ-45
input.
Fig.1
IR/RF remote
UP
STOP
DOWN

07212020JA 6 www.eliteproav.com
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V
trigger input allows your screen to synchronize its drop &
rise with the projector’s power cycle. The screen deploys
when the projector powers up and will retract when the
projector powers down. The 5-12 volt RJ45 cable connects
to your projector’s trigger output via a separate cable that
may or may not be provided by the manufacturer of the
projector. The trigger feature will not work without an
output cable from the projector, but it can be tested by
connecting the Red (+) and Green (-) cable to a 9-volt
battery.
3 prong power cord
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a
handheld remote control, or as a Wireless 5-12 volt trigger using the trigger cable. The radio frequency
technology can be programmed to send a wireless signal that synchronizes screen drop & rise with the projector’s
power cycle.
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step 1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to
control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
DC 5-12V out
The back of the
projector
Wireless 5-12V
trigger cable
For the following videos please see the following links:
Ceiling Installation Video – www.elitescreens.com/sakertabceilinginstall
Wireless Trigger Demonstration Video - www.elitescreens.com/sakertabtriggerdemo
Fig.2
Fig.3
3 Way Wall Switch
(does not have IR sensor)
IR “eye” receiver
Fig 5
Fig.4
RJ45 Input
5-12 volt
trigger cable

07212020JA 7 www.eliteproav.com
For more information, technical support or your local EliteProAV™
contact, please visit www.eliteproav.com