EliteProAV CineGrey 5D User manual

Rev. 03072019JA 1 www.eliteproav.com
Evanesce Tab-Tension CineGrey 5D®
Recessed In-ceiling Ambient Light Rejecting Projector Screen
Installation Guide
The screen material included is our award winning CineGrey 5D® which is a front projection material,
precisely formulated for environments with minimal control over room lighting. It was designed to enhance
picture brightness, offer accurate color fidelity, and improve contrast levels. The CineGrey 5D™ is best for
family rooms, educational facilities, conference rooms, house of worship or any applications in which incident
light is a factor.
In order for the CineGrey 5D® to maintain its projection qualities and optimum performance please refer to
the list below for proper maintenance and cleaning.
•Use a dry microfiber cloth to remove dust from the screen’s surface.
•When cleaning, use a damp microfiber cloth with warm water to remove any marks.
•Never rub or apply pressure when cleaning the surface.
•Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
•In order to avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or
any other sharp or abrasive objects.
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Unapproved changes or modifications (except for cutting the power cord for hardwire
installations) to this unit are prohibited and will void your warranty. For more information, please contact our
Technical Support Department at [phone] Ext. 604.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
•The power outlet supplying power to the unit should be close to the unit and easily accessible.
•Do not install the unit on uneven, inclined surfaces;
•Do not install in damp places to avoid an electric shock or short circuit.
•Do not place any heavy objects over the power cord.
•Position the power cord properly to avoid creating a trip obstacle.
•The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble
this unit by yourself. No one except authorized technicians can open and make repairs to this unit.
•Make sure the power source that this unit is connected to has a continuous power flow.

Rev. 03072019JA 2 www.eliteproav.com
•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid over heat.
•Do not handle the power plug when your hands are wet or your feet are in contact with water.
•Properly dispose of this equipment according to the environmental regulations in your area when
product is no longer of service.
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
•Avoid direct sun light, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from overheating.
•Cut off the power supply first before transportation or maintenance.
•To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious
damage or if there are any evident broken parts.
Installation Warning
The instructions provided in this user’s guide are for reference only. Please consult a professional
installation company for further installation and safety advice. The installer must insure that proper
mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is
not liable for any faulty installations. For limit adjustment instructions, please contact our Technical
Support Department at [phone] Ext. 604
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this equipment
causes harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
✓Reorient or relocate the receiving antenna of the device which may be casing the interference.
✓Increase the separation between the screen and the device’s receiver.
✓Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
ATTENTION: Regardless of the mounting method, the screen should be securely supported so that the
vibration or pulling on the viewing surface will not cause the casing to become loose or fall. The installer must
insure the fasteners that are used are of adequate strength and suitable for the installation location.

Rev. 03072019JA 3 www.eliteproav.com
Evanesce Tab-Tension Series | Controls and Accessories
A. IR
Remote
B. RF
Remote
C. Wall
switch
control box
D. 5-12 volt
trigger
cable
E. IR
extended
“eye” receiver
F. Wireless 5-
12v (3.5 mm)
mono trigger
cable
G. AAA
batteries
H. Bubble leveler
Screen operation
Electric Current: The screen operates on AC110V at 60Hz/ 1.18A
1.After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control the Evanesce Tab-Tension
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of sight
contact with a beam range of 30 feet. Aim the IR remote at the “eye” receiver once it
has been connected to the control box’s RJ45 port.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs directly into the
control box’s RJ45 port to present a low profile line-of-sight control option for your
IR remote control even in a recessed ceiling installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a direct line
of sight with a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall mount switch
with an up/stop/down button and plugs directly into the control box’s RJ45 port.
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V trigger
input allows your screen to synchronize its drop & rise with the
projector’s power cycle. The screen deploys when the projector
powers up and will retract when the projector powers down. The
5-12 volt RJ45 cable connects to your projector’s trigger output
via a separate cable that may or may not be provided by the
manufacturer of the projector. The trigger feature will not work
without an output cable from the projector, but it can be tested
by connecting the Red (+) and Green (-) cable to a 9-volt battery.
UP
STOP
DOWN
Fig.1
IR/RF remote

Rev. 03072019JA 4 www.eliteproav.com
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF
remote control serves as a dual purpose, independently as a handheld
remote control, or in conjunction with the Wireless 5-12 volt trigger
cable. The radio frequency technology can be programmed to send a
wireless signal to synchronize its drop/rise with the projector’s power
cycle.
Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger
cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and
able to control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
.
Hardware Parts List for Evanesce Tab-Tension
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Please make sure all parts listed below are included before proceeding with the installation
Installation Instructions
The Evanesce Tab-Tension allows access for above or below ceiling installation. Please follow the
instructions described in the following steps below for your type of installation.
Power
The Evanesce Tab-Tension Series includes a 3-Prong
Power Cord (2-Prong Power Cord for some countries)
for use in a non-concealed power outlet. If your
installation will be entirely concealed (including power
outlet), Elite Screens strongly recommends a hardwire
connection. Please refer to the image below for both
110v & 220v wiring information.

Rev. 03072019JA 5 www.eliteproav.com
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the
CineGrey 5D® Angular Reflective ALR (Ambient Light Rejecting) Screen.
Make sure to follow these instructions in order for the CineGrey 5D® to perform correctly.
•Angular-Reflective material is not compatible with ultra/short-throw projectors
•Minimum lens throw ratio 1.5x image width
•Ambient light must not come from the same direction as the projector
Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it is
important to position the projector so that the viewer will get the best possible image.
•Step 1: Establish the general “eye level” of the viewers
•Step 2: Set the appropriate projection level
•Step 3: Adjust the screen height level and projection angle
Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Rev. 03072019JA 6 www.eliteproav.com
A. Above ceiling installation instructions
Assembly
1. Insert the Hex Screw (B) through the Hanging Bracket’s (C) screw hole and secure with the Case
Rail Nut (A). Slide the Hanging Bracket (C) through the railing on top of the case.
2. Place the Suspension Bar (D) on the Hanging Bracket (C) and align with the hole as shown below.
Secure the Suspension Bar (D) with the Hex Screw (B), Washer (E) and the Hex Nut (F). Install the
Suspension Bars (D) to your ceiling according to their distance.
Optional Suspension Bar J-Hook (G)
1. Attach the Suspension Bar J- Hook (G) to the bottom of the Suspension Bar (D) and secure with the
Hex Screw (B), Washer (E) and Hex Nut (F).
D
B
E
E
F
B
E
E
F

Rev. 03072019JA 7 www.eliteproav.com
2. Attach the Suspension Bar J-Hook (G) to the Hanging Bracket (C) as shown in figure below. Install
the Suspension Bars (D) to your ceiling according to their distance.
Optional Installation (parts & hardware not included)
1. Place the Hanging Bracket (C) in the desired
location on the screen’s housing and measure the
distance as shown below. (L = Distance)
2. Mark the location of where the
screen will be installed according
to the distance (L) and then secure
the bolt to the ceiling.
3. Install the screen to the screw bolt as shown in the figure below.
G
C

Rev. 03072019JA 8 www.eliteproav.com
(N)
(K)
(H)
The ceiling wall
Install screw holes
Ceiling
Ceiling Panel
Ceiling installation space
The ceiling truss
B. Below ceiling installation instructions
1. Measure and cut the ceiling installation space. The width should not exceed 120mm. Measure the
length of your screen to determine the length.
Note: The length of the installation space is not greater than the screen size table (A3), and the width is
not less than the screen size table (A5). Consult the table below (C1) in regards to accommodating the
screen casing.
2. Drill 4 holes in the ceiling that correspond with the attachments on the various casing sizes.
3. The expanding bolts (H) mount into thick wood beams, stone or concrete and will support the screen.
Use the Socket wrench (N) to attach the hexagonal screws (K). The expanding bolts should be firmly
tightened and tested to make sure that they will hold the weight of the screen.
(J) and (L)

Rev. 03072019JA 9 www.eliteproav.com
4. Push the screen up into the space. Use the threaded rods (I) to attach the screen assembly to the
ceiling. The hexagonal screws (K) will connect the screen to the rest of the assembly. Once firmly in
place, use the nuts (J) to ensure a firm connection. Use the socket wrench (N) to make sure that the
bolts are firmly tightened.
5. Install plastic cover panel (O) to complete the installation.
For local Elite ProAV contact or Technical Support, please visit
www.eliteproav.com
Ceiling
Socket wrench (H)
Push
Ceiling
(I)
(K)
(M)