Elkay Composite VR Fountain EDFPVR217RC Instructions for use

98409C (Rev. B - 9/08)
EDFPVR217RC
Installation/Care/Use manual
Non-Refrigerated Composite VR Fountain
with Back Panel
To assure you install this model easily and correctly, PLEASE
READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR
COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instruc-
tions inside the fountain for future reference.
IMPORTANT! INSTALLER PLEASE NOTE.
THEGROUNDINGOFELECTRICALEQUIPMENTSUCHASTELEPHONE,COMPUTERS,ETC.TO
WATERLINESISACOMMONPROCEDURE.THIS GROUNDINGMAYBE INTHE BUILDINGOR MAY
OCCURAWAYFROMTHE BUILDING.THISGROUNDING CAN CAUSE ELECTRICALFEEDBACK
INTOAFOUNTAIN, CREATINGANELECTROLYSISWHICH CAUSESAMETALLICTASTEORAN
INCREASEINTHEMETALCONTENTOFTHEWATER.THISCONDITIONISAVOIDABLEBYUSING
THEPROPERMATERIALSAS INDICATED.ANYDRAIN FITTINGS PROVIDED BYTHE INSTALLER
SHOULDBEMADEOFPLASTICTOELECTRICALLYISOLATETHE FOUNTAIN FROMTHEBUILDING
PLUMBINGSYSTEM.
IMPORTANT
ALLSERVICETO BE PERFORMEDBY AN AUTHORIZED SERVICEPERSON
Installer

98409C (Rev. B - 9/08)
EDFPVR217RC
5/8" 16mm
13 7/8" 352mm
18 3/16" 462mm
2 1/4" 57mm
2 1/4" 57mm
27" 686mm
ADA
REQUIREMENT
7 1/8" 181mm
2 3/16" 56mm
13 3/4" 349mm
6 5/8" 168mm
33" 838mm
40 1/8" 1019mm
D
SEE DETAIL 1
FINISHED FLOOR
PAGE 2
EDFPVR217C ROUGH-IN
COMPOSITE BACK PANEL
LEGEND: A= RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4" O.D. DRAIN C = MOUNTING HOLES FOR SECURING FOUNTAIN TO WALL(BLOCKING & WALLSUPPORT IS REQUIRED IN THESE AREA FOR PROPER SUPPORT OF FOUNTAINS) D = 1 - 1/4' TRAP FURNISHED
FIG. 2
WASHER REQUIRED TO MINIMIZE
BREAKAGE OF FOUNTAIN.
(TYP. ALL 4 MOUNTING BOLTS,
MOUNTING BOLTS & WASHERS
NOT INCLUDED)
FINISHED FLOOR
35 3/4" 908mm
37 1/4" 946mm
29 3/4" 756mm
31 1/4" 794mm
4" 102mm
4" 102mm
3" 76mm
18 3/4" 476mm
5 1/8" 130mm
5 1/8" 130mm
1 5/16" 33mm
2 5/8" 67mm
C
BACBA
C
BABA
DETAIL 1

98409C (Rev. B - 9/08)
EDFPVR217RC
PAGE 3
1. Wall should already be framed for the fountain using the positioning dimensions shown in Fig. 2.
Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight).
2. Install rough-in plumbing as shown in Fig. 2. Run supply water inlet line and connect to a
service stop (not provided). Turn on supply water and flush thoroughly. Close water supply.
3. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back
panel and wall using (4) 5/16" bolts and washers (not provided). Bolts should be long enough to securely
fasten the fountain to the wall. Tighten securely, but do not over tighten. Over tightening will crack the
Marblyte Fountain.
4. Remove elbow from end of p-trap (item 1) and attach it to drain tube. Re-attach elbow to p-trap and
cut waste tube to required length using plumbing hadware and trap as guide.
5. Make water supply connections from service stop to the fountain strainer (Item 16) by inserting the
water inlet line into the inlet side of strainer until it reaches a positive stop about 3/4", (See Figure 6,
Page 7). Turn on water supply and check for leaks. Newly installed water supply line should be
insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is
above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by
reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG
is not covered by warranty.
7. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, adjust the screw on regulator item 14 by using a small screwdriver through the small
hole in the push button item 8 (See Fig.3). Clockwise adjustment will raise stream height and counter-
clockwise adjustment will lower stream height. For best adjustment stream height should be approxi-
mately 1-1/2" (38mm) above the bubbler.
8. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
INSTALLATION INSTRUCTIONS
COMPOSITE BACK PANEL
Care and Maintenance of ELKAY Composite Fountains
ElkayComposite fountains providean exremelydurable, nonporous surfacewhich resists staining. Careis
verysimple. Routine cleaning witha softsponge or cloth,or with wateror non-abrasive aerosolfoam
cleaner, is all that is normally needed to give many years of trouble free service. Cleaners left standing on
the fountain surface can dull the surface finish. Be certain to rinse all cleaning agents completely and polish
with a soft cloth.
Harshabrasive cleaners arenotrequired and shouldnotbe used.
Mildabrasives such asliquid automotive cleaningcompound or bakingsoda paste willremove simple
scratchesand stains. Cigarette burns can normallybe removed withoutnoticeable effect. Deeper
scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite
pad.
Tomaintainor regain luster and makecleaning easier, periodic applications of automobilewax orlike
products will keep the finish looking like new.

98409C (Rev. B - 9/08)
EDFPVR217RC
FIG. 3
812 9
BASIN
314
15 6
10
SEE FIG. 7
TOP VIEW
17
18
1
21
2, 4, 20 16
11 5, 7
SEE FIG. 3
13
FIG. 4
PAGE 4
22
25 23

98409C (Rev. B - 9/08)
EDFPVR217RC
FIG. 6
FIG. 5
PAGE 5
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the
orifice with a small round file not over 1/8" diameter or small diameter wire. CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is free of material deposits, regulate flow as in instructions on page 3(Step 9) or page 5(Step 7). If
replacement is necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal. To
remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing.(See Figure 6, Page 7). To
insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4".
TROUBLE SHOOTING & MAINTENANCE
PRINTED IN U.S.A. FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY• 2222 • CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH PUSH IN COLLET TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATIONOFQUICKCONNECTFITTINGS
NOTE:WATER FLOW
DIRECTION
BUILDINGWATER INLET
SERVICESTOP
(NOT FURNISHED)
1/4"O.D. TUBE
WATER INLET
TOCOOLER
3/8"O.D. UNPLATED
COPPERTUBECONNECT
COLDWATER SUPPLY
PARTNO.ITEMNO. PARTSLIST
Drain
Screw #10-24 x 1/2 PH TR HD-Z
Nut - Reg. Retain 1-1/8 - 24
Bottom - Plate (HRFG-E)
Bottom - Plate (HRFG-S)
Strainer-Beehive
Hex - Nut
Ferrule-Tailpipe
Push Button
Push Button Sleeve
Regulator Holder
Bubbler Assy VR
Push Button - Extension
Fountain - Galaxy Gray (HRFG-E)
Fountain - Galaxy Gray (HRFG-S)
Regulator
Screw Cap
Strainer
Panel - Dbl Back Galaxy Gray
Bubbler Locknut
Ball Anti-Rotation
Insert - Threaded
Nipple Assembly
Nut - Regulator Mounting
Poly Tubing (Cut To Length)
Wrench -Allen 7/64
LK464
112627543890
15005C
27658C
27201C
40038C
40045C
40619C
45662C
45738C
50986C
98118C
56087C
56053C
55969C
61313C
75672C
55996C
56114C
70012C
75575C
75554C
15029C
45736C
56092C
75674C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
NS
DESCRIPTION
FIG. 7
11
19
18
BASIN
21