Elkay EDFP19C series Installation manual

EDFP19C*B
98655C (Rev. B - 08/16)
Page 1
FIG. 1 FIG. 2
Installation/Care/Use Manual
Semi-Recessed Wall Mount Fountain with FLEXI-GUARD®
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICALAND OTHER
APPLICABLE CODES. After installation, leave these instructions inside the fountain
for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
11
SEE FIG. 3 SEE FIG. 4
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO
A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE
IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER
MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE
OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
Installer
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY

EDFP19C*B
98655C (Rev. B - 08/16) Page 2
LEGEND: A = RECOMMENDED WATER SUPPLY LOCATION, 3/8 O.D. UNPLATED COPPER TUBE CONNECT. B = RECOMMENDED LOCATION FOR WASTE OUTLET, 1-1/4” O.D. DRAIN. C = 1-1/4” TRAP NOT FURNISHED. D = MOUNTING HOLES FOR BASIN HANGER STRAP. E = MOUNTING HOLES FOR FOUNTAIN (VANDAL RESISTANT INSTALLATION ONLY). F = MOUNTING HOLES FOR FOUNTAIN (EASY ACCESS INSTALLATION ONLY).
FINISHED FLOOR
FIG. 3

EDFP19C*B
98655C (Rev. B - 08/16)
Page 3
DRAIN
19
BUBBLER ASSY
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN LOCKNUT ONLY TO
HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
17
FIG. 5FIG. 4
INSTALLATION INSTRUCTIONS
1. Connecting lines to be unplated copper and thoroughly ushed to remove all foreign matter before
connection to fountain.
2. Make water supply connections from service stop to the 3/8” O.D. unplated copper tube coming out
of the strainer. Turn on water supply and check for leaks. Newly installed water supply line should be
insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER
AS DAMAGE TO THE O-RINGS MAY RESULT.
3. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above
105 PSI, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSI or higher than 105 PSI is not
covered by warranty.
4. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies
greatly from this, turn adjustment screw on the regulator (Item 2). Clockwise adjustment will raise
stream height and counter-clockwise will lower stream height. For best adjustment stream should hit
basin approximately 6-1/2” (165mm) from bubbler.
TROUBLE SHOOTING AND MAINTENANCE
1. Orice Assy: Mineral deposits on orice can cause water ow to spurt or not regulate. Mineral deposits
may be removed from orice with a small round le not over 1/8” diameter or a small diameter wire.
CAUTION: Do not le or cut orice materials.
2. Stream Regulator: If orice is free of material deposits, regulate ow according to instruction 4 stated
above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize
an o-ring water seal. To remove tubing from the tting, relieve water pressure, push in on the gray collar
while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the tting until it
reaches a positive stop, approximately 3/4”.
LOCKNUT

EDFP19C*B
98655C (Rev. B - 08/16) Page 4
DESCRIPTION
112627543890
98531C
20415C
21560C
21708C
21710C
22611C
22718C
22905C
22907C
21222C
23003C
28959C
37077001
40107001
40045C
56073C
56092C
98790C
70016C
50198C
70278C
70935C
75547C
75555C
55996C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
NS
PART NO.ITEM NO.
PARTS LIST
15
2
3
11
SEE FIG. 4
2
9
SEE FIG. 3
2
67
10
1
18
24
Screw-#10-24 X .50 PHTC
Kit - Regulator/Holder/Nut
Basin Hanger Strap
Panel - Access
Push Bar Assy.
Bracket - Wall Mounting
Baseplate
Panel - Front
Panel - Left Hand Side
Panel - Right Hand Side
Basin
Bracket - Regulator Mounting
Bracket - Stop
Screw - #10-32 x .38 PHMS
Screw - #10-24 x .38 PHTC
Hex Nut 1-5/16
Bubbler Assy
Poly Tubing ( Cut To Length)
Kit - Strainer/Ferrule/Tailpipe/Gasket Assy
Nut - Hex #10-32
Bushing - Nylon
Rod - Support
Screw - Shoulder
Nut - Speed #10-24
Clip
In-Line Strainer
1
25
1
13
20
5
1
12
16
22
14
21
8
4
23
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484