Elkay LEXI-GUARD EDFP19C B Series Installation manual

EDFP19C*B
98655C (Rev. A - 1/11)
FIG. 1 FIG. 2
Installation/Care/UseManual
Semi-Recessed Wall Mount Fountain with FLEXI-GUARD®
Toassureyouinstallthismodeleasilyandcorrectly,PLEASEREADTHESESIMPLE
INSTRUCTIONSBEFORESTARTINGTHEINSTALLATION.CHECKYOURINSTALLA-
TIONFORCOMPLIANCEWITHPLUMBING,ELECTRICALANDOTHERAPPLICABLE
CODES.Afterinstallation,leavetheseinstructionsinsidethefountainforfuturereference.
IMPORTANT
ALLSERVICETOBE PERFORMEDBY ANAUTHORIZED SERVICEPERSON
1
SEE FIG. 3 SEE FIG. 4
IMPORTANT! INSTALLER PLEASE NOTE.
THEGROUNDINGOF ELECTRICALEQUIPMENTSUCH ASTELEPHONE,COMPUTERS,ETC.TO
WATERLINESISACOMMONPROCEDURE.THIS GROUNDINGMAYBEINTHEBUILDING ORMAY
OCCURAWAYFROMTHEBUILDING.THISGROUNDING CANCAUSE ELECTRICALFEEDBACK
INTOAFOUNTAIN,CREATINGAN ELECTROLYSISWHICHCAUSESAMETALLICTASTE ORAN
INCREASEINTHE METALCONTENTOFTHEWATER.THISCONDITION ISAVOIDABLEBYUSING
THEPROPER MATERIALSASINDICATED.ANYDRAIN FITTINGSPROVIDED BYTHE INSTALLER
SHOULDBEMADEOFPLASTICTOELECTRICALLYISOLATETHEFOUNTAINFROMTHEBUILDING
PLUMBINGSYSTEM.
Installer
NOTE: WATER FLOW
DIRECTION
BUILDINGWATER INLET
SERVICESTOP
(NOT FURNISHED)
1/4"O.D.TUBE
WATER INLET
TOCOOLER
3/8"O.D.UNPLATED
COPPERTUBE CONNECT
COLDWATERSUPPLY

EDFP19C*B
98655C (Rev. A - 1/11)
LEGEND: A=RECOMMENDED WATER SUPPLYLOCATION, 3/8 O.D. UNPLATED COPPER TUBE CONNECT. B= RECOMMENDED LOCATION FOR WASTE OUTLET, 1-1/4” O.D. DRAIN. C = 1-1/4” TRAP NOT FURNISHED. D = MOUNTING HOLES FOR BASIN HANGER STRAP. E = MOUNTING HOLES FOR FOUNTAIN (VANDAL RESISTANT INSTALLATION ONLY). F = MOUNTING HOLES FOR FOUNTAIN (EASYACCESS INSTALLATION ONLY).
FINISHEDFLOOR
PAGE 2

EDFP19C*B
98655C (Rev. A - 1/11)
DRAIN
20
18
23
25
24
34
BUBBLERASSY
NOTE:
WHENINSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 34)
ONLY TO HOLD PARTS SNUG IN POSITION.
DONOTOVER TIGHTEN.
17
19
FIG. 4FIG. 3
INSTALLATION INSTRUCTIONS
1. Connecting linesto beunplatedcopper andthoroughly flushedto remove allforeign matterbefore connec
tion to fountain.
2. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks. Newly installed water supply line should be insulated
after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
3. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
4. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies
greatly from this, turn adjustment screw on the regulator (Item 27). Clockwise adjustment will raise stream
height and counter-clockwise will lower stream height. For best adjustment stream should hit basin
approximately 6-1/2" (165mm) from bubbler.
TROUBLE SHOOTING AND MAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 4 stated
above.
3. Actuation of Quick Connect Water Fittings: Cooler is providedwith lead-free connectorswhich utilize
an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar
while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it
reaches a positive stop, approximately 3/4".
PAGE 3

EDFP19C*B
98655C (Rev. A - 1/11)
DESCRIPTION
112627543890
15005C
20415C
21560C
21708C
21710C
22611C
22718C
22905C
22907C
21222C
23003C
28959C
37077001
40107001
40045C
40322C
40572C
40575C
50074C
50198C
50986C
55997C
56011C
56073C
56092C
61314C
70016C
70208C
70278C
70935C
75547C
75555C
75580C
55996C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
NS
PARTNO.ITEMNO. PARTSLIST
15
22
3
11
SEE FIG. 4
2
9
SEE FIG. 3
27
67
10
29
26
32
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
FORPARTS,CONTACTYOUR LOCALDISTRIBUTOR OR CALL1.800.323.0620
PAGE 4
Screw - #10-24 x .50 PHTC
RegulatorRetaining Nut
Basin Hanger Strap
Panel - Access
Push Bar Assy.
Bracket - Wall Mounting
Baseplate
Panel - Front
Panel - Left Hand Side
Panel - Right Hand Side
Basin
Bracket - Regulator Mounting
Bracket - Stop
Screw - #10-32 x .38 PHMS
Screw - #10-24 x .38 PHTC
Hex Nut 1-5/16
Orifice Assy.
Tailpipe
Strainer & Ferrule Assy
Gasket - Tailpipe
Bushing - Nylon
Regulator Holder
Pedestal
Housing Assy.
Bubbler Assy
Poly Tubing ( Cut To Length)
Regulator
Nut - Hex #10-32
Screw - #10-24 x .38 PHTC
Rod - Support
Screw - Shoulder
Nut - Speed #10-24
Clip
Locknut 3/8-18
In-Line Strainer
1
33
1
13
28
5
1
12
16
30
14
21
8
4
31