Elkay SOFT SIDES EZLMSN-EDFPVM217DK Instructions for use

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 1
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain  ttings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
SOFT SIDES®Fountains with Vandal Resistant Bubblers
and Vandal Resistant Water Dispenser
INSTALLATION & USE MANUAL
LZLMSN-EDFPVM217DK
(Shown with optional ACCESS12X38-5 access
panel.)
EZLMSN-EDFPVM217DK

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 2
**NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI)
Figure 1 - Rough-in Dimensions

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 3
Figure 3 - LZLMSN-EDFPVM217DK Tube Routing
REQUIRED TOOLS AND MATERIALS
These tables show special tools and/or additional
materials (not provided) which are necessary to
complete installation of these units:
Figure 2 - EZLMSN-EDFPVM217DK Tube Routing
TO BUBBLER
20
FILTER
ASSEMBLY
11
10
10
WATER
INLET
Special Tools
Item Description Quantity
NONE
Additional Materials Not Included
Item Description Quantity
Unplated copper inlet pipe
Service Stop
90° 1-1/4” Drain Line
1-1/4” Tee Drain Line
1
2
3
4
1
1
1
1
TO BUBBLER
11
TO BOTTLE
FILLER
10
10
1. Make water supply connections (Fig. 10). Install a
shut-off valve and union connection to building water-
supply (valve and union not provided). Turn on water
supply and ush the line thoroughly.
Caution: DO NOT SOLDER tubes inserted into the
strainer or lter head as damage to the o-rings may
result.
2. Install mounting frame (instructions supplied with
mounting frame.
3. (For LZLMSN-EDFPVM217DK) Install the lter head
to the bracket, then install lter bracket on mounting
frame (Fig. 8), plumb from the lter outlet using the ¼”
elbow, poly tubing and ¼ x ¼ x ¼” tee, install lter.
3a. (For EZLMSN-EDFPVM217DK) Install ¼” tee,
copper tubing and strainer per (Fig. 2).
4. Install supplied 4” poly tubing and armaex to the
outlet of the previously installed tee or strainer. Connect
supplied ¼ x ¼ x ¼ tee to the 4” poly tubing.
5. Hang main panel on mounting frame hanger. Make
sure the poly tube do not get pinched between the panel
& mounting frame. Ensure the panel engages at the top.
Align fountain holes with mounting frame holes.
6. Remove protective coating from main panel.
7. Installing water Dispenser Place the unit into the
stainless panel and frame. Align the holes in the water
dispenser with the nuts in the panel. Attach the dispens-
er to the panel using four (4) supplied 1/4 x 20 screws.
10
TO BUBBLER
10
10
10
12
22
11
TO BUBBLER
11
TO
BOTTLE
FILLER
10

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 4
Connecting Catch Basin Waste Drain
Installing the drain is highly recommended to prevent
basin over ow.
The following steps cover the installation of the drain.
1. Remove the two screws attaching the drain basin to
the water dispenser. Remove the drain basin.
2. Place the drain basin on a  at, hard surface, such as
a piece of sacri cial wood. Carefully drill a hole in the
basin using a 1" hole saw using the centering-dimple
as a guide to center the hole saw.
Note: Do not use a 1-1/8" hole saw as this will make the
opening too large.
3. Trial  t the strainer. If the strainer does not  t, carefully
open the size of the hole. If it  ts well, place a small
amount of plumbers putty around the lip of the strainer
 ange and insert it into the hole.
4. Install the O-ring over the strainer threads.
5. Thread the strainer into the drain adapter.
Needle-nose pliers can be used to hold the drain
adapter from the top while tightening. Ensure that
the connection creates a watertight seal. The drain
adapter must be facing to the left.
Note: Twisting the strainer instead of the drain adapter
can compromise the seal created by the plumber's
putty.

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 5
6. Attach one end of the 3/4 inch  exible drain hose to
the 3/4 inch barbed drain adapter connection using the
supplied hose clamp. The supplied  exible drain is 13
inches long. If a longer drain hose is required, it must
be installer-supplied.
7. Place the drain basin back into the water dispenser
and reinstall the two screws.
8. Connect the drain adapter into the household waste
drain pipe.
If the p-trap is located inside a sealed walled, it must
have permanently-glued joints. If the p-trap is in an
accessible location, a standard non-glued p-trap is
acceptable.
Install the water dispenser’s front cover.
9. Line up the front panel with the dispenser frame and
attach using the  athead screws and a 3/32” hex
wrench.
10. Install the metal grate cover using the 4 Screws.
Note: Always consult local plumbing codes prior to
installation.

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 6
Figure 4 - Upper Panel Installation
Figure 5 - Fountain Installation
9
19
View From Rear
21
3
1. Install fountains with (8) 5/16-18 HHMS & (8) 5/16-18
nuts (provided) (Fig. 5). Connect the ¼” water lines from
each fountain to the remaining openings on the tee (cut
lines to  t as needed).
2. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip
trap. Trap on the bottle  ller side must be 1-1/2” O.D.
(provided by others).
3. Make  nal water supply connections.
4. These products are designed to operate on 20-105
PSI supply line pressure. If inlet pressure is above 105
PSI, a pressure regulator must be installed in the supply
line.
Caution: Any damage caused by connecting these prod-
ucts to a supply line with pressure lower than 20 PSI or
higher than 105 PSI IS NOT covered under warranty.
5. Verify proper dispensing from the bottle  ller by
placing a cup, under the water dispenser spout and
press the button and verify water dispenses. Note: the
 rst initial dispenses might have air in the line which may
cause a sputter. This will be eliminated once all air is
purged from the line. A steady stream of water assures all
air is removed. Check for leaks.
6. Check stream height from bubbler. Stream height is
factory set for 35 PSI supply. If supply pressure varies
greatly from this, remove push button (Item 5 - Fig. 8)
and adjust the screw on the regulator (Item 4 - Fig. 8). To
remove push button, loosen set screw (Item 7 - Fig. 8) on
bottom of the sleeve (Item 6 - Fig. 8) and pull out on the
button. Clockwise adjustment will raise stream height and
counterclockwise movement will lower stream height. For
best adjustment stream should hit basin approximately
6-1/2” from the bubbler. Reassemble the push button by
pushing in on button and tighten the set screw (Item 7 -
Fig. 8) in the sleeve (Item 6 - Fig. 8).
7. Install the bottom cover plates on fountains (Fig. 4).
8. Tighten back panel screws (Item 9 - Fig. 4).
9. Optional: Mount optional panels. Mount bracket on
wall per rough-in instructions. Slide tongue of panel under
edge of already installed panel. Tighten screws.
Once the installation is complete, the water has been
turned on, and any trapped air has been bled from the
system re-check for any water leaks.
19
18
13
24,25
8
15
2
14
5

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 7
NOTE:
When installing replacement bubbler and
pedestal, tighten locknut only to hold parts
snug in position.Do Not overtighten.
Figure 6 - Bubbler Details
VANDAL-RESISTANT BUBBLER DETAIL
1
Fig. 7
1
Filter Head
Assembly
used after 01/01/2021
2
3/8”
Wa
ter
Inlet
WATERSENTRY®PLUS FILTER PARTS LIST
(See Fig. 7)
ITEM
NO. PART NO. DESCRIPTION
1
2
51300C
51469C
Filter Assy-3000 Gal.
Assy-Filter & Brkt includes Fltr Head/
Mtg Brkt/John Guest Fittings/Screws
BASIN
1/4” tube
(if required – not included)
Locknut
Figure 8
17
16
4
56
7
Once the installation is complete, the water has been
turned on, and any trapped air has been bled from
the system re-check for any water leaks.

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 8
A
LCOVE
A
SSEMBLY
MAIN ENCLOSURE
ASSEMBLY
Figure 9
Figure 8
28
25
25
25
25
26
26
26
29
29
27
PARTS LIST
ITEM
NO. PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
98481C
28782C
28783C
LK464
98530C
45960C
45663C
75672C
112627543890
111008343890
56092C
1000001994
55996C
2000001257
55000661
55000665
40045C
28823C
56280C
75560C
1000001772
111577343890
62223C
1000002062
Kit - Vandal-Resistant Bubbler Assy
Fountain Arm - Short
Fountain Arm - Long
Drain
Kit - Regulator/Nut/Holder
Push Button
Push Button Sleeve
Screw - Cap #6-32 x 5/16
Screw - #10-24 x .50 PHTC
Screw - #10-24 x .62 HHSM
Poly Tubing 1/4” (Cut To Length)
Kit - Tee 1/4 x 1/4 x 1/4 (3 Pack)
Strainer
Back Panel Assembly
Bottom Cover Plate - Short
Bottom Cover Plate - Long
Hex Nut
Regulator Mounting Bracket
Edge Trim - Chrome
Screw - 5/16-18 x 1.00 HHMS
Kit - Elbow 1/4 x 1/4 (3 Pack)
Nut - Hex 5/16-18
Copper Tube - 3/8” Cut to Length
Kit - Tee 1/4 x 1/4 x 3/8 (3 Pack)

2000001276 (Rev. A - 01/24)
EZLMSN-EDFPVM217DK LZLMSN-EDFPVM217DK
Page 9
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
ELKAY MANUFACTURING COMPANY • 1333 BUTTERFIELD ROAD SUITE 200 DOWNERS GROVE, IL 60515 • 630.574.8484 • www.elkay.com
Figure 10 – Water Supply Connections
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY Installation Package
The components for installation are packed in
three separate boxes, regardless of the type
of unit being installed. The boxes contain the
following:
Box No. 1: Wall Frame(s)
Box No. 2: Fountain(s), Arm(s) and Panels
Box No. 3: Water Dispenser
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orice Assembly: Mineral deposits on orice can
cause water ow to spurt or not
regulate. Mineral deposits may
be removed from the orice by
poking with a small round le
not over 1/8” diameter, or using
a small diameter wire.
DO NOT le or cut orice material.
Stream Regulator: If orice is clean, regulate ow as
in Step 14 of the installation instructions. If replacement
is necessary, see parts list for correct regulator part
number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting,
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Fig. 11) To insert tubing,
push tube straight into tting until it reaches a positive
stop (approximately 3/4”).
REPLACEMENT PART LIST
ITEM
NO. PART NO. DESCRIPTION
24
NS
25
26
27
28
29
98546C
1000004698
2000001260
1000005392
56331C
70793C
1000001812
Kit - Aerator Replacement
Fitting - Hose to Trap
Kit - Alcove
Kit - Drain
Connector
Elbow 1/4 O.D. X 90
Kit - Bottle Filler Drain
NS = NOT SHOWN
Figure 11 – Quick Connect Fittings
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C