Elkay EZWS-EDFPBM117K Instructions for use

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 1
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
$Q\GUDLQ¿WWLQJVSURYLGHGE\WKHLQVWDOOHUVKRXOGEHPDGHRIplastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
LZWS-EDFPBM117KEZWS-EDFPBM117K
SWIRLFLO®Fountains with FLEXI-GUARD®
and ezH2O® Bottle Filler
INSTALLATION & USE MANUAL

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 2
**NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER *GFCI)
Figure 1 - Rough-in Dimensions
 RR
 RR
 RR2.3.2:2 +47)7&.3(433*(9.43 &3)&((*8894 '4991*+.11*7 *1*(97.(&18
 RR
 RR
 RR
 RR
.58
<&89*1.3*
.58
8:551>
 RR
 RR
 RR
 RR
 RR
&)&
7*6:.7*2*39
 RR
 RR
 RR
&(9.;&9.43 8*3847
+.3.8-*)+1447
459.43&1&((*885&3*1
&((*885&3*17*6:.7*)
+47.389&11&9.438<.9-
347*&7&((*88
459.43&1&((*885&3*1 &((*885&3*1 7*(422*3)*)+47 .389&11&9.43<.9- 347*&7&((*88
'4991*7+.11*7)7&.3 97&57*6:.7*)8:551.*) '>.389&11*7
 RR
 RR
 RR
 RR
/:3(9.43'4= 14(&9.43

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 3
Figure 3 - LZWS-EDFPBM117K Tube Routing
REQUIRED TOOLS AND MATERIALS
These tables show special tools and/or additional materials
(not provided) which are necessary to complete installation
of these units:
12
12
25
TO BUBBLER
12
Figure 2 - EZWS-EDFPBM117K Tube Routing
TO BUBBLER
21
FILTER
ASSEMBLY
13
12
12
WATER
INLET
Special Tools
Item Description Quantity
NONE
Additional Materials Not Included
Item Description Quantity
Unplated copper inlet pipe
Service Stop/Shut-off Valve
90° 1-1/4” Drain Line
1-1/4” Tee Drain Line
1
2
3
4
1
1
1
1
WATER
INLET
TO BUBBLER
31 24
TO BOTTLE
FILLER
TO BUBBLER
26
13
31
14
TO BOTTLE
FILLER
1. Make water supply connections (Fig. 11). Install a shut-off
valve and union connection to building water supply (valve
 DQGXQLRQQRWSURYLGHG7XUQRQZDWHUVXSSO\DQGÀXVK
the line thoroughly.
Caution: DO NOT SOLDER tubes inserted into the
 VWUDLQHURU¿OWHUKHDGDVGDPDJHWRWKHRULQJVPD\UHVXOW
2. Install mounting frame (instructions supplied with mounting
frame.
3. (For LZWS-EDFPBM117K) IQVWDOOWKH¿OWHUKHDGWRWKHEUDFNHW
 WKHQLQVWDOO¿OWHUEUDFNHWRQPRXQWLQJIUDPH)LJSOXPEIURP
 WKH¿OWHURXWOHWWRWKHFKLOOHULQOHWZLWKó´HOERZSRO\WXELQJDQG
 ó[óXQLRQLQVWDOO¿OWHU
3a. (For EZWS-EDFPBM117K) Install strainer on the input tube to
the chiller (Fig. 2).
4. Install ó[ó[7HHRQEXLOGLQJZDWHUVXSSO\WXEH,QVWDOO
 VXSSOLHG´SRO\WXELQJDQGDUPDÀH[WRWKHRXWOHWRIWKHSUHY
 RXVO\LQVWDOOHGWHH&RQQHFWVXSSOLHGó[ó[óWHHWRWKH´SRO\
tubing. With the back panel standing close to the frame, connect
 ´SRO\WXEHWRWKHERWWOH¿ller.
5. Hang main panel on mounting frame hanger. Make sure the
power cord, reset switch wire & poly tube do not get pinched
between the panel & mounting frame. Ensure the panel engages
at the top. Align fountain holes with mounting frame holes.
6. Remove protective coating from main panel.
7. InstallUHVHWVZLWFKIRUERWWOH¿OOHU)LJ6QDSWKHVZLWFKLQWR
 SRVLWLRQDIWHUORFDWLQJZLUHVWKURXJKVORW:UDSXSWKHH[FHVV
cord.
12

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 4
NOTE:
When installing replacement bubbler and pedestal, tighten
locknut only to hold parts snug in position. Do Not overtighten.
Figure 6 - Bubbler Details
Figure 4 - Upper Panel Installation
Figure 5 - Fountain Installation
15 Reset Switch
22

19
23
23
View From Rear
5
Basin
1
Locknut
22
17
InstallIRXQWDLQVZLWK++06QXWV
 SURYLGHG)LJ&RQQHFWWKHó´ZDWHUOLQHVIURPHDFK
fountain to the remaining openings on the tee at the remote
 FKLOOHUFXWOLQHVWR¿WDVQHHGHG
9. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D. slip trap.
 7UDSRQWKHERWWOH¿OOHUVLGHPXVWEH´2'SURYLGHGE\
others).
10. Make ¿QDOZDWHUVXSSO\FRQQHFWLRQV
11. These products are designed to operate on 20-105 PSI
supply line pressure. If inlet pressure is above 105 PSI, a
pressure regulator must be installed in the supply line.
Caution: Any damage caused by connecting these products
to a supply line with pressure lower than 20 PSI or higher
than 105 PSI IS NOT covered under warranty.
12. MakeHOHFWULFDOFRQQHFWLRQVWRWKHERWWOH¿OOHUDQGUHPRWH
chiller. The LCD Bottle counter should illuminate.
13. Verify SURSHUGLVSHQVLQJIURPWKHERWWOH¿OOHUE\SODFLQJDFXS
hand or any opaque object in front of sensor area and verify
 ZDWHUGLVSHQVHV1RWHWKH¿UVWLQLWLDOGLVSHQVHVPLJKWKDYHDLU
in the line which may cause a sputter. This will be eliminated
once all air is purged from the line. A steady stream of water
 DVVXUHVDOODLULVUHPRYHG7KHVHQVRUKDVDVHFRQGPD[L
mum ON time. It may be necessary to step away from the
beam a few times to purge all air. Check for leaks.
14. Check stream height from bubbler. Stream height is factory set
for 35 PSI supply. If supply pressure varies greatly from this,
remove push button (Item 7 - Fig. 9) and adjust the screw
 RQWKHUHJXODWRU,WHP)LJ7RUHPRYHSXVKEXWWRQ
remove setscrew from bottom of sleeve (Item 6). Insert a small
punch in screw hole and push up while grasping the push but
ton and pull forward removing the push button. Clockwise
adjustment will raise stream height and counterclockwise
movement will lower stream height. For best adjustment
 VWUHDPVKRXOGKLWEDVLQDSSUR[LPDWHO\´IURPWKHEXEEOHU
Reassemble the push button by pushing in on button until the
push button catches in the sleeve. Reinstall the setscrew (Item
24) in the sleeve (Item 6).
15. Install the cover plates.
16. Install the bottom panel, tighten screws (Fig. 4).
17. Optional: Mount optional panels. Slide tongue of panel under
edge of already installed panel. Tighten screws.
Back
Panel
16
16

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 5
Figure 8 - Fountain Body Assembly
Figure 9 - Push Button Assembly
6
7

20
21
11
See Fig. 6
2
9
See Fig. 6
3
12

4
10

5
21
Figure 7
1
2,3
3
2,3
ITEM
NO.
Filter Assy-3000 Gal.
.LW)LOWHU+HDG)LWWLQJVLQFOXGHV-RKQ*XHVW
Fittings
$VV\)LOWHU%UNWLQFOXGHV)OWU+HDG0WJ%UNW
-RKQ*XHVW)LWWLQJV6FUHZV
1
2
3
51300C
&
51469C
DESCRIPTION
PART
NO.
WATERSENTRY®PLUS FILTER PARTS LIST
(See Fig. 7)
´
Water
Inlet
3

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 6
VERIFY CONTROL BOARD SOFTWARE
1) To verify the software program of the control board the unit will
need to be shut down and restarted. The chiller (if present) does
not need to be shut down and restarted.
2) Shut down the unit by unplugging the power cord from the wall
outlet or switching off the circuit breaker to the unit.
3) Restart the unit by plugging the power cord back into the wall
outlet or by switching on the circuit breaker to the unit.
4) Upon start up, the bottle count display will show the software
designation of BF11 or BF12.
ACCESSING THE PROGRAMMING BUTTON
7RDFFHVVWKHSURJUDPEXWWRQUHPRYHVFUHZSXOOEDFN
cover plate on lower fountain arm (Fig. 5). Reset button is located
above fountain arm.
RESET THE FILTER MONITOR
,QVWUXFWLRQVDSSO\WR¿OWHUHGXQLWVRQO\
'HSUHVVWKHSURJUDPEXWWRQIRUDSSUR[LPDWHO\VHFRQGVXQWLO
the display changes then release. The display will change and
scroll through two messages:
“RST FLTR” – Reset Filter Monitor
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
3) When the display changes to “RST FLTR”, depress the button
again. The display will change to show “FLTR =”. Depress the
button again and the display will show “FLTR =0”
4) The Green LED should be illuminated indicating that the visual
¿OWHUPRQLWRUKDVEHHQUHVHW
SETTING RANGE OF THE IR SENSOR WHERE APPLICABLE
'HSUHVVWKHSURJUDPEXWWRQIRUDSSUR[LPDWHO\VHFRQGVXQWLO
the display changes then release. The display will change and
scroll through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button
again. The display will change to show
“RNG SET” - Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
³)/76,=(´6HOHFW¿OWHUFDSDFLW\
“RST BCNT” - Reset bottle count
3) When display shows “RNG SET” push program button once the
display will show current value (can be 1 – 10) e.g. “RNG = 3”.
4) Once display shows current value push the program button to
scroll through value of 1 – 10. Select the desired range setting,
"1" being closest to sensor and "10" being farthest away.
2QFHUDQJHLVVHOHFWHGDOORZDSSUR[LPDWHO\VHFRQGVWRSDVVDQG
then the display will go back to bottle counter and be in run mode.
7HVWERWWOH¿OOHUE\SODFLQJERWWOHRUKDQGLQIURQWRIVHQVRUWR
make sure water is dispensed.
SETTING UNIT TYPE
'HSUHVVWKHSURJUDPEXWWRQIRUDSSUR[LPDWHO\VHFRQGVXQWLOWKH
display changes then release. The display will change and scroll
through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button
again.
The display will change to show
“RNG SET” - Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
³)/76,=(´6HOHFW¿OWHUFDSDFLW\
“RST BCNT” - Reset bottle count
Continued from below:
3) When display shows “UNIT TYPE” push program button once the
display will show current value. Can be REFRIG or NON-RFRG
4) Push button once to change value. Once value is selected the display
will show the new value. (Can be REFRIG or NON-RFRG)
³5()5,*³VWDQGVIRUUHIULJHUDWHGSURGXFW,QWKLVVHWWLQJWKHÀRZUDWHLV
estimated at 1.0 gallon per minute.
“NON-RFRG“ - stands for nonrefrigerated product. In this setting the
ÀRZUDWHLVHVWLPDWHGDWJDOORQVSHUPLQXWH%RWK³5()5,*³DQG
“NON-RFRG“ simulate 1 bottle equal to 20 oz.
5) $OORZDSSUR[LPDWHO\VHFRQGVWRSDVVDQGWKHGLVSOD\ZLOOUHWXUQWR
bottle counter and be in run mode.
RESETTING BOTTLE COUNT
'HSUHVVWKHSURJUDPEXWWRQIRUDSSUR[LPDWHO\VHFRQGVXQWLOWKH
display changes then release. The display will change and scroll
through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll through
the two messages above for three cycles and then default back to bottle
count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button again.
The display will change to show:
“RNG SET”- Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
³)/76,=(´6HOHFW¿OWHUFDSDFLW\
“RST BCNT” - Reset bottle count
If the button is not pushed again the display will scroll through the four
messages above for three cycles and return to run mode.
3) When display shows “RST BCNT” push program button once the
GLVSOD\ZLOOVKRZFXUUHQWYDOXHHJ³´
4) Once display shows current value push the program button once more
WRUHVHWEDFNWR7KHGLVSOD\ZLOOVKRZ%7/&7 IRUDSSUR[LPDWHO\
seconds and then return to run mode showing 00000000 bottles.
NOTE: Once the bottle count is reset to zero there is no way to
return to the previous bottle count.
5) Testing the bottle counter:
5()5,*XQLWV3ODFHERWWOHRUKDQGLQIURQWRIVHQVRUIRUDSSUR[LPDWHO\
9 seconds to see bottle counter count 00000001,
7KLVLVEDVHGRQ¿OOLQJDR]ERWWOH
NON-RFRG units: Place bottle or hand in front of sensor for
 DSSUR[LPDWHO\VHFRQGVWRVHHERWWOHFRXQWHUFRXQW
7KLVLVEDVHGRQ¿OOLQJDR]ERWWOH
SETTING FILTER CAPACITY
'HSUHVVWKHSURJUDPEXWWRQIRUDSSUR[LPDWHO\VHFRQGVXQWLOWKH
display changes then release. The display will change and scroll through
two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll through
the two messages above for three cycles and then default back to bottle
count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button again.
The display will change to show:
“RNG SET“- Range set for IR sensor.
“UNIT TYP“ - Type of unit (REFRIG or NON-RFRG)
³)/76,=(´6HOHFW¿OWHUFDSDFLW\
“RST BCNT“ - Reset bottle count
If the button is not pushed again the display will scroll through the four
messages above for three cycles and return to run mode.
3) When display shows “FLT SIZE” push program button once. The display
will show current value. Can be 3000GAL or 6000GAL.
4) Push program button again to display the desired “FLT SIZE”.
$OORZDSSUR[LPDWHO\VHFRQGVWRSDVVDQGWKHGLVSOD\ZLOOUHWXUQWR
bottle counter and be in run mode.
BF11 - BF12 PROGRAM
SETTING THE CONTROL BOARD

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
Page 7
Figure 10
FILTER
(OPTIONAL)
MOUNTING
FRAME DRAIN
LOCATION
MAIN PANEL
MOUNTING
FRAME
2&.3'4&7)
.7'4&7)
1*)'4&7)
841*34.)
,74:3)
;.41*9
349:8*)
(&55*)
>*114<
349:8*)
(&55*)
+4:75.3
(433*(947
+.;*5.3
(433*(947
<-.9*
<-.9*
3*:97&1
7*)
,7**3,74:3)
'1&(0
1.3*;419&,*
2&1*
51:,
+*2&1*
7*(*59&(1*
Electrical Diagram
-81&7,21
BOX

0000001029 (Rev. I - 03/19)
EDFPBM117WS EDFPBM117WS-F
3DJH
1
2
3
4
5
6
7

9
10
11
12
13
14
15
16
17

19
20
21
22
23
24
25
26
56073C
&
&
45767C
&
&
&
&
56163C
0000000930
&
56092C
1000001994
55996C
99003C

70432C

75560C
75632C
1000001772

&
1000002062
62223C
&
Kit - Bubbler Assy
%DVLQ6ZLUOÀRZ
Lower Shell
Fountain Body
Cover Plate
Sleeve
.LW6ZLUOÀR3XVKEXWWRQ6SULQJ
Kit - Regulator/Spring/Nut
Gasket - Drain
Assy - Drain/Tailpipe
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Kit - Tee 1/4 (3 Pack)
Strainer
Reset Switch Assy
6FUHZ[++60
6FUHZ[7+60
6FUHZ[++60
6FUHZ[++06
6HWVFUHZ[
.LW&(OERZ[3DFN
1XW+H[
Bracket - Support
.LW7HH[[3DFN
&RSSHU7XEH´&XWWR/HQJWK
7HH´
Figure 11 – Water Supply Connections
PARTS LIST
ITEM NO. PART NO. DESCRIPTION
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
127)851,6+('
1/4” O.D. TUBE
WATER INLET
TO COOLER
´2'813/$7('&23-
PER TUBE CONNECT
COLD WATER SUPPLY
DESCRIPTION
&
&
&
&
&
Kit - Electrical Package
Kit - EE Sensor
Kit - Solenoid Valve Replacement
Kit - Aerator Replacement
.LW+DUGZDUH:DWHUZD\3DUWV
BOTTLE FILLER REPLACEMENT
PART KITS
ITEM NO. PART NO.
27

29
30
31
Installation Package
The components for installation are packed in
two separate boxes, regardless of the type of unit
being installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Fountain(s), Arm(s) and Panels
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
2UL¿FH$VVHPEO\0LQHUDOGHSRVLWVRQRUL¿FHFDQ
FDXVHZDWHUÀRZWRVSXUWRUQRW
regulate. Mineral deposits may
EHUHPRYHGIURPWKHRUL¿FHE\
SRNLQJZLWKDVPDOOURXQG¿OH
not over 1/8” diameter, or using
a small diameter wire.
DO NOT ¿OHRUFXWRUL¿FH
material
Stream Regulator: ,IRUL¿FHLVFOHDQUHJXODWH
ÀRZDVLQ6WHSRIWKHLQVWDOODWLRQLQVWUXFWLRQV,I
replacement is necessary, see parts list for correct
regulator part number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
RULQJZDWHUVHDO7RUHPRYHWXELQJIURPWKH¿WWLQJ
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Fig. 13) To insert tubing,
SXVKWXEHVWUDLJKWLQWR¿WWLQJXQWLOLWUHDFKHVDSRVLWLYH
VWRSDSSUR[LPDWHO\´
Note: Screw the locknut hand tight to seal
)253$576&217$&7<285/2&$/',675,%872525&$//
5(3$,56(59,&(,1)250$7,2172//)5((180%(5
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
Figure 12 – Quick Connect FittingsFigure 11
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
6,03/<386+,1
78%(72$77$&+
TUBE IS SECURED
IN POSITION
386+,1&2//(7
TO RELEASE TUBE
386+,1*78%(,1%()25(
38//,1*,7287+(/3672
RELEASE TUBE
A B C

For Technical Service, please contact us at 1.800.476.4106
0000000755 (Rev. D - 03/19)
Elkay - www.elkay.com
Halsey Taylor - www.halseytaylor.com
MFWS200 / MFWS220 MOUNTING FRAME INSTRUCTIONS
MFWS 220
MFWS200
GROUNDING DETAIL FLOOR LINE
WOOD OR STEEL
FRAME SHOWN
(NOT INCLUDED)
OPTIONAL BRACKET
FOR ACCESS PANEL
OPTIONAL BRACKET
FOR ACCESS PANEL
5/16" SCREWS OR BOLTS
(20) REQ'D - NOT PROVIDED)
FRAME
4 REQ'D P/N 111577343890
(NUT - PROVIDED)
4 REQ'D P/N 111577243890
(BOLT - PROVIDED)
(P/N 111008343890 - PROVIDED)
10 1/4”
(260MM)
OPTIONAL FOR
ACCESS PANEL
3”
(76MM)
3”
(76MM)
37 1/2”
(952MM)
31 1/2”
(800MM)
25”
(635MM)
8 5/8”
(219MM)
1. Cut a square rectangular wall opening
line. These dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117.1.
2. Reinforce the wall opening on all sides so that it will adequately support the water fountain. This reinforcement must
support up to 150 lbs static load and provide a means for securing the frame assembly in place.
3. Install plumbing rough-ins.
4. Remove frame assembly and related hardware from packaging. Attach the two frames together through the upright
supports with (4) 5/16” x 3/4” (19mm) long bolts and nuts (provided). Tighten securely.
5. Install the frame assembly
Secure the frame to the wall thru holes with (12) 5/16” bolts or screws (not provided). Tighten securely.
NOTE: Be sure that frame is squared in location. Do not use less than required screw quantity and size.
6. Mounting Frame Wiring Instructions:
a. Turn off electrical supply to installation location circuit.
b. Remove Junction Box Cover to gain access to electrical box.
c. Connect electrical supply using conduit, wiring, and connectors per local and national codes.
d. Connect ground wire to ground screw (provided).
e. Connect black wire to ”hot” power supply line 120V 60Hz, 1 phase.
f. Connect white wire to Neutral line.
g. Replace Junction Box Cover.
h. Connect electrical power to installation location circuit.
OUTLET BOX
GROUND SCREW LOCATION