Elkay DRKR10C Installation manual

DRKR10C
98712C(Rev.A-3/11)Page1
Countertop Fountains
INSTALLATION, CARE & USE MANUAL
!CAUTION
:
Reviewthese instructions before beginninginstallation. Be sure thatinstallation
conformsto allplumbing, electrical and other applicablecodes.
!
WARNING
:
When installation is complete, ensure these instructions are left in the plastic bag
providedinsidetheinstalledunit for future reference.
!WARNING
:
Servicetobeperformed by authorized servicepersonnelonly.
INSTALLER
NOTE: It is commonpractice toground electrical hardwaresuch as telephones,computers and otherdevices
toavailable water lines.Thiscan,however, causeelectrical feedback inthe plumbing circuit,which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic
taste to it or has a noticeable increase in the metallic content of the water.
Wheninspecting plumbingcircuit, remember the line maybe groundedsome distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.Any
drainfittings provided bythe installer shouldbe made of plastic whichwill electronically isolatethe
fountainfrom the remainder ofthebuilding’s plumbing circuits.

98712C(Rev.A-3/11)
DRKR10C
Page2
9-3/8" DIA.
238mm
1. Make 9-3/8” (238mm) diameter cutout in desired location
on countertop. (See Figure 1)
2. Install bubbler assembly to fountain.
3. Apply caulk (not provided) around cutout and waste
opening.
4. Place fountain over opening and drop in strainer.
(See Figure 2)
5. From underside, position and secure tiedown bracket
using waste fitting. (See Figure 3)
6. Use screws with nuts (provided) to tighten unit to
countertop. Wipe off excess caulking.
(See Figure 3)
7. 1-1/4” O.D. waste tube furnished. 1-1/4” slip trap,
waste elbow and extension not provided.
8. Make water supply connections from service stop to the
3/8” O.D. unplated brass nipple coming out of the
bubbler. Turn on water supply and check for leaks. Newly
installed water supply line should be insulated after leak
check is completed.
9. These products are designed to operate on 20-105
PSIG supply line pressure. If the supply pressure is
above 105 PSIG, a pressure regulator must be installed
in the supply line. Any damage caused by reason of
connecting these products to supply line pressures
lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
10. STREAM HEIGHTADJUSTMENT: Stream Height is
factory set at 45-50 PSI. If supply pressure varies greatly
from this, remove items 5 and 6 (See Figure 6) from
bubbler assembly and adjust the screw on the regulator
assembly (Item 9). Clockwise adjustment will raise
stream height and counterclockwise will lower the stream
height. A stream height of 1-1/2” (38mm) is
recommended.
Figure1
Figure2
Figure3 Stream HeightAdjustment
Figure4

DRKR10C
98712C(Rev.A-3/11)Page3
FINISHED FLOOR
O9 7/8"
251mm
12"
305mm
3"
76mm 1 1/2"
38mm
5 1/2"
140mm
2 1/8"
54mm
7"
178mm
AS
REQUIRED
3/8" IPS SUPPLY
1-1/4" O.D. WASTE
O9 3/8"
238mm
CUTOUT
Mounting Bracket is adaptable
to Countertop Thickness of
3/8" (10mm) to 1-1/2" (38mm)
Figure5
**NOTE:ROUGH-INDIMENSIONS MAYVARY1/2”(13mm)PLUSORMINUS.
BUBBLER CAN BE MOUNTED ON RIGHT OR LEFT SIDE AS DESIRED.

98712C(Rev.A-3/11)
DRKR10C
Page4
72043210
LK142
10031C
100322740560
40048C
40089C
40322C
45675C
61313C
70012C
72460042
A54800
A54888
1
2
3
4
5
6
7
8
9
10
11
12
13
PARTSLIST
ITEMNO. PARTNO. DESCRIPTION
Basin Assembly
Bubbler Assembly
RegulatorNut
Gasket
Button Cap
Nut Cover Cap
Orifice Assembly
Bubbler Body
Regulator Assembly
Lock Nut
Metal Washer
Nipple
Screen
PRINTEDINU.S.A. FORPARTS,CONTACTYOURLOCALDISTRIBUTOROR CALL1.800.323.0620
ELKAY MANUFACTURING COMPANY• 2222 CAMDEN COURT • OAK BROOK, IL60523 • 630.574.8484
TROUBLESHOOTING& MAINTENANCE
Orifice Assembly: Mineral deposits on orifice can
cause water flow to spurt or not regulate. Mineral deposits
may be removed from the orifice by poking with a small round
file not over 1/8” diameter, or using a small diameter wire.
!CAUTION
:
DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean, regulate flow as in
Step 10, Page 2 of the installation instructions. If replacement
is necessary, see parts list for correct regulator part number.
Basin
Figure6
12
6
5
3
8
4
13
11
9
7
10
2