Elkay VRCHD8 Series Installation manual

Page 1 1000002233 (Rev. A - 11/14)
VRCHD8*2BQ, LVRCHD8*2BQ
Uses HFC-134A refrigerant
2, 3, 5
8
14, 17, 18
20
44
25
21
40
43
See Fig. 4
45
1, 4
6, 7
11
See Fig. 3
21
19
33, 34
16
40
31
13
23, 30
Fig. 1
26
36
24
38
INSTALLATION, CARE & USE MANUAL
VRCHD8 Series Barrier-Free Water Coolers
TM

Page 21000002233 (Rev. A - 11/14)
VRCHD8*2BQ, LVRCHD8*2BQ
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED) TO ACCEPT 3/8” O.D. UNPLATED
COPPER TUBE.
La UBICACION RECOMENDADA de ABASTECIMIENTO DE AGUA. APAGUE VALVULA (no AMUEBLADO) ACEPTAR 3/8 O. D. El TUBO del COBRE de UNPLATED L’EMPLACEMENT DE PROVISION D’EAU RECOMMANDE. ETEINDRE LA SOUPAPE (PAS FOURNI) ACCEPTER 3/8 O.D. LE TUBE DE CUIVRE DE UNPLATED. B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼” DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4” DE SORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DE ALAMBRES (3) DE SUMINISTRO ELÉCTRICO BOÎTE ENCASTRÉE D’ALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6” (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTI- LACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6” (152 mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE ET LE MUR.
F = 5/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 5/16 PARA SUJETAR LA UNIDAD A LA PARED TROUS D’ÉCROUS 5/16 POUR FIXER L’APPAREIL AU MUR
Fig. 2
* ADA REQUIREMENT
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
18 9/16" 471mm
6 13/16" 173mm
1 1/2" 38mm
27" * 686mm
31 1/2" 800mm
3" (3")
FINISHED FLOOR
12 5/8" 320mm
2 5/8"
67mm
2 1/2" 63mm
11/16" 18mm
4 9/16"
116mm
7 1/4"
185mm
3 1/2" 89mm
4 1/2" 114mm
5" 127mm 9 15/16"
252mm
C
L
18 3/8"
467mm
21 3/8"
543mm
25"
635mm
29 5/8" 753mm
1 3/8"
35mm 1 3/8"
35mm
5 3/4"
146mm 5 3/4"
146mm
B
5/16" ( 8 mm ) DIA. (5 HOLES)
EE
D
A
F
32 9/16"
827mm
FILTER
C
6 1/2" 165mm
11 1/16" 280mm
HANGER BRACKET
8 1/8" 206mm
RIM HEIGHT
ORIFICE HEIGHT
18 3/16"
463mm
ADA
REQUIREMENT

Page 3 1000002233 (Rev. A - 11/14)
VRCHD8*2BQ, LVRCHD8*2BQ
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of
cooler by removing one (1) screw.
2) Mount the hanger bracket and trap as shown
in Figure 2.
NOTE: Hanger Bracket MUST be supported
securely. Add xture support carrier if wall will
not provide adequate support.
IMPORTANT:
 6-13/16 in. (173mm) dimension from wall to
centerline of trap must be maintained for proper
t.
 Anchor hanger securely to wall using all ve
(5) 5/16 in. dia. mounting holes.
3) Install straight valve for 3/8” O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be
certain the hanger bracket is engaged properly
in the slots on the cooler back as shown in Figure
2.
5) Loosen the two (2) screws holding the lower
front panel at the bottom of cooler base (Use
torx bits sold separately). Remove the front
panel and set aside.
6) Connect water inlet line--See Note 4 of General
Instructions.
7) Remove the slip nut and gasket from the trap
and install them on the cooler waste line mak-
ing sure that the end of the waste line ts into
the trap. Assemble the slip nut and gasket to
the trap and tighten securely. Recommend
fastening cooler to wall using 5/16” bolt holes.
(see g.2, “F”)
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If
supply pressure varies greatly from this, adjust
screw using the access hole in the pushbutton
(insert screwdriver). CW adjustment will raise
stream and CCW adjustment will lower stream.
For best adjustment, stream should hit basin
approximately 6-1/2” (165mm) from bubbler.
CLEANING
9) Recommended: Elkay’s Stainless Butler
Cleaner (Item LKSB16EA).
Warm, soapy water or mild household
cleaning products can be used to clean
the exterior with a clean, soft cloth. Use
of harsh chemicals, petroleum based or
abrasive cleaners will void the warranty.
Fig. 4
15
23
25
18
14
33
30
44
13
42
17
39
14
34
8
37
40
27
28
35
40
29
1
Fig. 3
VANDAL RESISTANT BUBBLER DETAIL
15
1
4
Basin
Estanque
Bassin
1
41
12
40

Page 41000002233 (Rev. A - 11/14)
VRCHD8*2BQ, LVRCHD8*2BQ
Fig. 5
Filter Installation Detail
Fig. 6
25
22
22
Fig. 7
220V/240V POWER INLET DETAIL
9
10
TO “N” TERMINAL
ON POWER INLET
(RIBBED SIDE)
TO GROUND TERMINAL
ON POWER INLET
(GREEN WIRE) TO “L” TERMINAL
ON POWER INLET
(SMOOTH SIDE)
ITEM
NO.
Filter Assy-1,500 Gal.
Kit-Filter Head Fittings, includes
John Guest 3/8” elbow tting
Assy-Filter & Bracket includes
Fltr Head/Mtg Bkt/John Guest
Fittings/Screws
1
2
3
51299C
98926C
0000000746
DESCRIPTION
PART
NO.
FILTER PARTS LIST
(See Fig. 6)
1
2 2
3

Page 5 1000002233 (Rev. A - 11/14)
VRCHD8*2BQ, LVRCHD8*2BQ
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
56305C
100806740570
75705C
15009C
19037000
30824C
31395C
35839C
35826C
35827C
1000002194
28898C
27124C
50986C
45878C
56092C
15005C
61313C
66703C
66810C
70002C
111543043890
45768C
75583C
28870C
28876C
45662C
45738C
75672C
56163C
36282C
28893C
66762C
28875C
40045C
28878C
28877C
55996C
45736C
75739C
56087C
56033C
66661C
45888C
1000002195
75520C
28874C
Gasket - Bubbler
Grommet - Compressor Mtg.
Stud - Compressor Mtg.
Nipple - Bubbler
Clip - Compressor Mtg.
Fan Blade
Fan Motor
Cold Control
Power Inlet
Power Cord
Compressor Serv. Pak
Panel - Access
Cover - Cold Control
Holder - Regulator
Bubbler Assy.
Tubing - Poly (Cut To length)
Retaining Nut
Regulator
Drier
Evaporator Assembly
Screw - #10 x 1/2” Lg. HHSM
Nut - #6-32 Hex.
Drain Plug 1-1/2
Elbow - 5/16” x 1/4”
Cabinet - Stainless Steel
Bracket - Fan Mounting
Button - Push
Sleeve - Push Button
Cap Screw
Gasket - Drain
Wire - Fan Motor
Panel - Front Lower (NS)
Condenser
Shroud Fan
Hex Nut
Bracket - Support
Shelf - Evaporator Mounting
Strainer (See “General Instructions”)
Half Nut - Regulator
Screw - #10-24 x .50 Pinned Torx
Extension - Push Button
Washer
Heat Exchanger
Assy. Drain/Tailpipe
Kit - Elect/Relay/Cover/Overload
Torx Tool - T25
Hanger Bracket
PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
NS
NS
ITEM NO.
*
*REPLACE WITH SAME COMPRESSOR USED
IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water
coolers or orders for repair parts MUST include Model No. and
Serial No. of cooler, name and part number of replacement part.
PARTS LIST 220 - 240V/50Hz