Elm Plus EPL1002 User manual

Assembly Instruction
CAST ALUMINIUM PATIO
LOVESEAT CHAIR
Elm Plus, LLC

1
Bolt (H)
Nut Cap (L)
Washer (I) Spring Washer (J) Nut (K)
HARDWARE LIST
PRE-ASSEMBLY PREPARATION
WARNING! DO NOT LET CHILDREN PLAY IN OR AROUND THE UNIT DUE TO THE POSSIBLE RISK OF FINGER ENTRAPMENT
• Please read through this instruction before beginning assembly.
• Two adults assembly is recommended.
• Clear out the space for assembly and lay out all parts base on Parts List, extra room will allow you to easily
determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
• Keep small parts and pieces away from children until fully assembly.
• Do not fully tighten the bolts until all have been inserted and hand tightened.
• Please check for any loose screws and tighten them before use.
PANEL AND FITTINGS IDENTIFICATION
Backrest Panel (A) Right Arm Panel (B) Left Arm Panel (C)
Qty: 1Qty: 2
Middle Arm Panel (E) Back Cushion (F)
Qty: 2Qty: 1
Qty: 1
Seat Cushion (G)
Qty: 2
Qty: 9
Bolt (M)
Qty: 5
Qty: 9
Qty: 9
Qty: 9 Qty: 9
Seat Panel (D)
Qty: 2
M6*28mm
M6 M8*30mm
M6 M6 M6
Bolt (N) Washer (O)
Qty: 3 Qty: 7
M8*45mm M8

2
D
T
Q
P
O
Spring Washer (P) Nut (Q) Nut cap (R) Wrench (S)
Qty: 7Qty: 7 Qty: 7 Qty: 1
M8
Wrench (T)
Qty: 1
M8
M8 M8 M6
Step 1
Stand Left Arm Panel (C) up.
Attach Left Arm Panel (C) to Seat Panel (D) by using 2 Bolts (M), 2 Washers (O),
2 Spring Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
M X 2 O X 2 P X 2 Q X 2
C
M

3
Step 2
Attach Seat Panel (D) to Middle Arm Panel (E) by using 2 Bolts (N), 2 Washers (O),
2 Spring Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Attach Right Arm Panel (B) to Seat Panel (D) by using 2 Bolts (M), 2 Washers (O), 2 Spring
Washers (P), 2 Nuts (Q) with Wrench (T) as shown below.
DO NOT FULLY TIGHTEN BOLTS.
Step 3
D
M
N X 2 O X 2 P X 2 Q X 2
B
T
Q
P
O
D
N
O
O
P
Q
T
E
M X 2 O X 2 P X 2 Q X 2

4
Attach Backrest Panel (A) to Left Arm Panel (C) and Middle Arm Panel (E) by using
4 Bolts (H), 4 Washers (I), 4 Spring Washers (J), 4 Nuts (K) with Wrench (S) as shown
below.
DO NOT FULLY TIGHTEN BOLTS.
Step 4
Repeat step 4 to attach the other Backrest Panel(A) to Right Arm Panel(B).
DO NOT FULLY TIGHTEN BOLTS.
Step 5
H X 4 I X 4 J X 4 K X 4
H X 4 I X 4 J X 4 K X 4
H
A
S
K
J
I
C
A
H
S
K
J
I

5
Step 6
Now fully and securely tighten all nuts at all joints.
Add Nut Caps (L) on bolt ends behind Backrest Panel (A) and Nut Caps (R) on bolt
ends under Seat Panel (D) to protect skin or clothing from getting snagged.
Adjust height
for balance
Adjust low
for balance
Adjust Pre-installed Levellers
height for balance
L
R
Adjust the pre-installed levellers at the bottom of the chair legs until the chair is level
with the ground.
Step 7
L X 8 R X 6

6
Put Back Cushion (F) and Seat Cushion (G) on the Chair. Inspect it and make sure all
parts are adequately connected. Your chair is ready for use.
Caution: This Chair can only be used on a flat, level surface.
Step 8
F
G