ElMod ThinkTank M16 Assembly instructions

ThinkTank M16
Instructions for Assembly and Handling
Please read this document carefully!
Overview of connectors
1 Power supply 2 Fuse for turret and light functions
3 Connector for turret section 4 Volume control
5 Spea er cables 6 microSD-card with sample sets
7 Receiver Connectors (4 Channels & BEC) 8 Main motor connector
9 Steering servo connector 10 Light connector
11 Main switch 12 PC configurator lin
L1 Status-LED 1 (drive functions) L2 Status-LED 2 (sound functions)
Assembly
•Remove the original PCB carefully. Do not damage the sensitive connectors and
thin cables!
•Replace the original electronics PCB with the ElMod M16. It fits exactly in the
present mounting holes. Fasten the board with two screws.
•Attach the original cables to the corresponding connectors (power supply, main motor, steering servo, turret section, lights). Ta e care!
The connectors for the power supply and the main motor may be accidentally swapped!
•Attach a proper RC-receiver (4-channel) to the corresponding cables. The wire color pin assignment is as follows:
Ch Control Function
1right stic Acceleration
2Steering
3left stic Turret, weapon and special functions
4
The Thin Tan M16 provides the power supply for the receiver (BEC, stabilized 5V DC) via the red/blac wires which are part of the
proportional cable set.
Depending on the receiver it may be necessary to adjust the channel order or swap its movement direction
Chec the manual of your rc gear for details.
•The receiver may be placed in the hollow space above the drive wheel (see picture)
•Connect an appropriate loudspea er (8 Ohm) to the spea er wires.
•Jac the vehicle up, so that the chains can move freely.
•Attach a full charged battery to the power supply connector. Switch the RC-radio and the Thin Tan M16 board on.
•Both LEDs comes on after 3-4 seconds. If a LED remains off or blin s, see the following table to determine the cause.
L1 (status drive functions)
off No power (chec the battery and the main switch)
blin ing No receiver signal detected. Chec the RC gear!
on Operational
L2 (status sound function)
off No SD-Card detected or faulty card
blin ing Communication problem or faulty hardware
on Operational
•Move the left stic to the upper most position to ignite the engine. If another function shows up, chec the wiring of the receiver and the
setup of your radio! Disable all mixers in the radio. If necessary chec the function and mapping of the radio channels with a common
servo.
•Adjust the volume if you don't hear the engine noise.
•Chec the drive, steering and light functions.
•Switch the power off and attach the turret section.
•Power on the board and chec the turret functions (rotation, elevation, shot) with the left stic of the radio.
•The vehicle is now operable.
© ElMod GbR - 11-10-11

Steering and control
To accelerate and bra e move the right stic in the vertical axis. To drive left or right, move the right stic in the horizontal axis.
The light, turret and special functions are mapped to the left stic as listed in the following table.
çè Full deflection Turret rotation ëFast movement User sound 1
êé Up to 66% deflection AA-gun elevation ìFast movement Light on/off
éFull deflection Shot on/off íFast movement User sound 2
êFull deflection Engine on/off îFast movement User sound 3
Nicht geeignet für Kinder unter 14 Jahren.
Not suitable for Children under 14 years
Ne convient pas pour des enfants de moins de 14 ans
Niet geschikt voor kinderen onder de 14 jaar
ElMod Thomas Kusch, M. Sc. & Jürgen K. Huber GbR
Steinenbergstr. 24
D-72622 Nürtingen
ElMod Th Kusch, M Sc & Jürgen K Huber GbR
info@elmod eu http://www elmod eu
© ElMod GbR - 11-10-11