Elpro Technologies 925U-2 User manual

925U-2 wireless mesh networking I/O and gateway
installaon guide
Statutory requirements
FCC: This device complies with Part 15.247 of the FCC Rules. Operation is
subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
FCC: Unlicensed operation limits the radio power. High gain aerials may only
be used to compensate for cable losses.




The 925U-2 module ships from the factory as a bridged meshing radio. If
communication with the older legacy 915U-2’s is required, radio’s operating
mode can be changed with firmware.

Use Figure 1 as a guide for installing an antenna and attaching it to the module.

Earth Stake
For maximum
range, install
above local
obstruc�ons.
Earth Conductor
at least 5 AWG
(16 mm2)
*
Wavelength: 13"(33 cm)
Weatherproof
Connections
(recommended:
3M™23 self-
bonding tape)
Mast
Coaxial Cable
GND
at least 11 AWG (4 mm2)
Stress
Relief
Loop
Antenna*
GND
Surge Arrestor
(recommended)
925U-2
Provide good ground
connection to mast,
module, and surge
arrestor.
If ground conditions
are poor, use more
than one stake.
1 Wavelength
(minimum)

• Download and install configuration application “CConfig” from ELPRO
website www.elpro.com.au
• Connect to PC using supplied USB cable
• Connect to the device at 192.168.111.1
• The PC will be automatically assigned an IP address via DHCP
Username: user
 user
Install Guide 925U-2 Eecve Sept 2022

925U-2 wireless mesh networking I/O and gatewayinstallaon guide Install Guide 925U-2
Eecve Sept 2022
ELPRO Technologies
29 Lathe St
Virginia, QLD 4014
Australia
www.elprotech.com
Telephone:
Global:[phone]
ELPRO Technologies Inc
2028 East Ben White Blvd,
#240-5656 Austin, TX 78741-6931
USA
Telephone:
USA: [phone]
ELPRO is a registered trademark.
All other trademarks are property of their respective owners.
© 2022 ELPRO
All Rights Reserved

All connections must be SELV <50 Vac and <60 Vdc.
The following illustrations show the ports on the 925U 2.
PWR
RF
232
485
LED Indicator
Lights
I/O Connectors
RJ-45 Ethernet Port
(connects to hub or switch)
USB Port RS-232 Port
ETHERNET USB RS232 SUPPLY
+-
GND BAT SUP SUP
+
B A
-+

The ground (GND) and “SUP –“
terminals are connected internally to
the ground terminal.
Connect the screw terminal on
the end plate to ground for surge
protection.

An on-board RS-485 terminating
resistor provides line
attenuation for long runs.
Place terminating resisters at
each end of the RS-485 cable.

Use the DIP switches in the side
access panel to select analog input
voltage and current, external boot,
and default configuration settings.
 
1AI3 current/voltage
2AI3 current/voltage
3AI4 current/voltage
4AI4 current/voltage
5 Unused
6Enables default configuration

The digital input/output channels can be wired as inputs or outputs.
 
Transistor
Switch
Device (NPN)
Voltage-free Contact
TTL CMOS
Output
D1 D3 D4 D5 D6 D7 D8 GND
+24V
D2
DC Load
200mA max
+ –
D1 D3 D4 D5 D6 D7 D8
GND +24V
D2
30V DC max
 
mA
Loop-Powered
Sensor
Exernally
Powered
Sensor
Power Supply
D7 D8
GND +24V
AI1
+
AI1
_AI2
+
AI2
_AI3 AI4
AO1
+
AO2
+
GND +24V
mA
Loop-Powered
Sensor
Power Supply
Externally
Powered
Sensor
DIP Switch Setting
for Current IP
GND +24V
AI1
+
AI1
_AI2
+
AI2
_AI3 AI4
AO1
+
AO2
+
GND +24V
1 2 3 4 5 6
ON
 
AI
PLC
COM
AI1
+
AI1
_AI2
+
AI2
_AI3 AI4
AO1
+
AO2
+GND +24V
0–25V
Sensor
0–5 Vdc
Sensor
+24V
AI1
+
AI1
_AI2
+
AI2
_AI3 AI4
AO1
+
AO2
+GND +24V
V
V
DIP Switch Setting
for Voltage IP
ON
1 2 3 4 5 6
ETHERNET USB
RS232
B A
-+
115S-xx 115S-xx
RS-485
B A
B A B A
-+-+
USB RS232 SUPPLY
+
-
GND BAT SUP SUP
+
15-30 Vdc
Supply
3A Fuse
Optional
10.8–15 Vdc
Lead Acid
Battery
–
+
USB Host
Conguration
Switches
Side
Access
Panel