Elvox 40510 User manual

Instruction manual
40510
7” Due Fili Plus porter switchboard

2
7” Due Fili Plus porter switchboard
GENERAL INFORMATION
Device 40510 is a switchboard for the DueFili Plus video door entry system, equipped with a 7-inch colour screen. It can
be used in hands-free mode or with a handset.
The instruction manual can be downloaded from www.vimar.com
Installation rules
Installation should be carried out in compliance with the current regulations regarding the installation of electrical equipment
in the country where the products are installed.
Regulatory Compliance
EMC directive
Standards EN 60065, EN 61000-6-1 and EN 61000-6-3.
INFORMATION FOR USERS UNDER DIRECTIVE 2002/96 (WEEE)
In order to avoid damage to the environment and human health as well as any administrative sanctions, any appli-
ance marked with this symbol must be disposed of separately from municipal waste, that is it must be reconsigned
to the dealer upon purchase of a new one. Appliances marked with the crossed out wheelie bin symbol must be collected
in accordance with the instructions issued by the local authorities responsible for waste disposal. For more information call
the free-phone number 800-862307.
This product was developed using FreeRTOS
TM
software - http://www.freertos.org/

3
VIMAR group
7” Due Fili Plus porter switchboard
Main functions
The switchboard offers the following functions:
1. making and receiving audio calls with the indoor units;
2. receiving audio/video calls from the speech units;
3. implementing automatic self-starts from the speech units;
4. forwarding speech unit calls to indoor units;
5. calling another switchboard;
6. managing warnings from indoor units;
7. managing speech unit locks, stair lights and system relays;
8. activating CCTV cameras for monitoring purposes;
9. logging calls, warnings and activations.
Advanced functions
1. management of Competence Areas
2. management of operation time bands (Day/Night)
3. interception / non-interception of calls (Indoor/Outdoor mode)
The following languages are supported:
1. Italian
2. English
3. French
4. German
5. Spanish
6. Greek
7. Portuguese
Technical characteristics
Technical data:
• Supply voltage: 28VDC nominal
Power supply via power supply unit 6923 (not supplied)
• Maximum absorption: 300 mA
• Absorption in standby: 86 mA
• 7-inch colour display, 800x480 pixel resolution, 16:9 format
• Ambient class: Class A1 (indoor use)
• Protection degree IP30
• Operating temperature: -5°C to +40°C (indoor use)
• Operating ambient humidity 10 - 80% (non-condensing)
• Electronic chimes with different tunes (10 melodies).
• Dimensions: 242x213x221 mm (WxHxD with support open)
• DIP switch for line impedance termination.

4
7” Due Fili Plus porter switchboard
Front view
Keyboard
Handset
Screen
Rear and side view
Mini USB connector
for connection to
a PC
RJ45 socket for connection
to the Due Fili Plus system
via stud
Dip switch for video
termination

5
VIMAR group
7” Due Fili Plus porter switchboard
Keyboard
Key Description
Menu / Select
Exit / Cancel
Up
Down
Alphanumeric keys
Hands-free
End Conversation
Internal / External
Day / Night
Self-start
Keyboard lock
Hold
Input / Transfer
F1 (programmable)
F2 (programmable)
Contacts List
List of alert notifications
Events list
Lock

6
7” Due Fili Plus porter switchboard
Indicators
LED Status Description
Steady light Power - Switchboard on
Steady light Switchboard connected to a PC via USB
Flashing light Unanswered call indication and/or alert notification

7
VIMAR group
7” Due Fili Plus porter switchboard
External connections
Switchboard 40510 is connected via the “Interconnecting stud” and the corresponding RJ45 Cat. 5E connection cable
supplied.
+U +I
PRI
-
6923
BU OG BK RD
WHBNYEGN
**
Important: Strictly observe the connections on the con-
necting stud. Inverted wiring connections may lead to the
switchboard being damaged.
**
Due Fili Bus
Important: The maximum connection dis-
tance between power supply unit 6923
and the interconnecting stud is 10 m.
Interconnecting
stud
Length: 3 m
Mains
Power
Supply unit

8
7” Due Fili Plus porter switchboard
+U +I
PRI
-
6923
BU OG BK RD
WHBNYEGN
• Note: We recommend connecting the cables with a fork Faston of a size suited to the stud screws, and inserting
it between the head of the screw and the washer, arranging the cables so as to avoid contact between adjacent
Fastons.
Connection correspondence table: interconnecting stud - Due Fili system
Connection box terminals Connection box wire colour Due Fili audio / video door entry system
BU 1•
Blue 1 (Due Fili Bus)
OG 2•
Orange 2 (Due Fili Bus)
BK 3•
Black from power supply unit 6923 terminal -
RD 4•
Red from power supply unit 6923 terminal +I
GN 5•
Green -
YE 6•
Yellow -
BN 7 •
Brown -
WH 8•
White -
Access hole for Due Fili
Bus and power supply
cables
to switchboard
Video Termination
Select DIP switch to terminate the video signal
A) if the BUS cable enters terminals BU (1), OG (2) of the switchboard interconnecting stud and continues to another indoor
unit.
B) when a BUS cable with typical impedance of 100 Ohm (Elvox cable 732I or 732H) enters terminals BU (1), OG (2) of the
interconnecting stud and the riser stops in the switchboard.
C) when a BUS cable with typical impedance of 50 Ohm (Cat. 5 or Cat. 6 twisted pair cable) enters terminals BU (1), OG (2) of
the interconnecting stud and the riser stops in the switchboard.

9
VIMAR group
7” Due Fili Plus porter switchboard
GRAPHICAL INTERFACE
First line
The following icons may appear on the first line of the screen, starting from the left:
The ringtone is disabled. The switchboard nevertheless accepts calls and it is possible to answer.
A notification that a door is open has been received.
The microphone is disabled.
The keyboard is locked.
The conversation is taking place in hands-free mode.
The conversation is taking place via the handset.
Internal mode
External mode

Internal mode with call filter enabled

External mode with call filter enabled
Automatic Internal/External enabled
Automatic Internal/External disabled
Last line
The date and time appear on the last line, in the format chosen during configuration.

10
7” Due Fili Plus porter switchboard
Standby
Stand-by screen
The switchboard enters standby mode after a specified time. In this mode, screen brightness is reduced and electricity
consumption limited.
If a function button is pressed when the switchboard is in standby, that function is implemented immediately once the
switchboard has awoken. In standby, the key wakes up the switchboard without implementing any other functions.
Keyboard
The keys carry out their functions when released.
If pressed for at least 0.5 seconds, the following keys perform another function:
KEY STANDBY TALKING
Ringtone mute Microphone mute
(Not applicable) Change parameter in adjustment
Self-start list
Activation list
To serve similar events “indirectly” (Not applicable)
To serve similar alerts “indirectly” (Not applicable)
With events / alert filter enabled, enter the
filter ID.
(Not applicable)
When viewing the contacts list, exit directly
to standby if the filter is enabled
(Not applicable)
When viewing events / alert, to delete them
after entering the installer PIN
(Not applicable)
During clock adjustment, requests the date/
time from the device configured as Master
Clock
(Not applicable)

11
VIMAR group
7” Due Fili Plus porter switchboard
Keyboard lock
The key locks the keyboard. To unlock it, press the key again, enter the unlock PIN (default 0000) and press
the key . When locked, calls can still be answered by pressing the key or lifting the handset. At the end of
the call the switchboard reverts to locked mode.

12
7” Due Fili Plus porter switchboard
Basic settings
In standby, the key calls up the settings menu, which can be navigated in circular manner using the and
keys. To configure a setting, navigate the list using the and keys until you have selected the desired option
(highlighted in orange), then press . The list of available options and possible settings will follow:
Basic settings menu
• Ringtone mute
Using the and keys, you can enable/disable the switchboard ringtone. When the ringtone is disabled,
the icon will appear in the top right-hand corner of the screen. Press to confirm or press to cancel
without saving.
Default: ringtone enabled.
Ringtone enable Ringtone disable
• Select call melody from speech unit
Use keys and to select one of the 10 available melodies (identified by letters A to J) to use as a ringtone
for calls from the speech unit. The switchboard plays back the selected ringtone. Press to confirm or press
to cancel without saving.
Default: melody B.

13
VIMAR group
7” Due Fili Plus porter switchboard
Speech unit call ringtone Ringtone selection
• Select landing call melody
Use keys and to select one of the 10 available melodies (identified by letters A to J) to use as a ringtone
for calls from the landing. The switchboard plays back the selected ringtone. Press to confirm or press
to cancel without saving.
Default: melody C.
Landing call ringtone
• Select call melody from indoor unit or switchboard
Use keys and to select one of the 10 available melodies (identified by letters A to J) to use as a ringtone
for calls from an indoor unit or switchboard. The switchboard plays back the selected ringtone. Press to
confirm or press to cancel without saving.
Default: melody D.
Intercom call ringtone

14
7” Due Fili Plus porter switchboard
• Ringtone volume control
Use keys and to increase/decrease the ringtone volume, which is indicated by the horizontal bar. Press
to confirm or press to cancel without saving.
NOTE: the set level is used for all ringtone types (calls from the speech unit, landing, indoor unit or switchboard).
Default: level 5.
Ringtone volume selection Ringtone volume control
• Date and time adjustment
The keys and can be used to select the field you wish to change, moving right and left respectively. Use
the number keys to change the value of the selected field. Press to confirm and update the date and time,
after checking its validity. If the date and time are not correct, the switchboard will emit an error tone and move the
cursor to the first incorrect field.
Date and time adjustment selection Date and time configuration
NOTE: In the event of a power cut, the device will be able to continue to update the date and time for 48 hours.
NOTE: If the relative function is enabled using SaveProg, the switchboard will automatically adjust the clock at the
start and end of Daylight Saving Time. At 02:00 on the last Sunday in March, it will set the time to 03:00, while at
03:00 on the last Sunday in October, the time will be set to 02:00. By default, this function is not enabled.
NOTE: A short press of the key enables/disables the Master Clock function. When this function is enabled, a
tick symbol √ appears alongside the time, and the device will act as the system reference for the date and time, so
that all the switchboards will be synchronized automatically (without having to manually set the date and time on
each device).
Press the key for 0.5 seconds and the device will be immediately synchronized with the system's Master Clock
switchboard, if present.

15
VIMAR group
7” Due Fili Plus porter switchboard
Master Clock activation
• Key tone
Use the keys and to enable/disable the tone produced whenever a key is pressed (keystroke feedback).
Press to confirm or press to cancel without saving.
Default: enabled.
Key tone
• Installer menu
After selecting the option and pressing , the installer PIN will be requested. The menu then allows access to
the advanced settings:
Installer menu Installer PIN input

16
7” Due Fili Plus porter switchboard
Advanced settings
The settings menu can be navigated in circular manner using the and keys. To configure a setting, navigate the
list using the and keys until you have selected the desired option (highlighted in orange), then press . The
list of available options and possible settings will follow:
Advanced settings menu
• Switchboard ID
Press to start the ID configuration procedure. In the next screen, enter the desired ID and then press
to confirm. Wait for the verification process to finish; a progress bar will be displayed on the screen. If the verification
is completed successfully, the new switchboard ID will be displayed; if not, the device will retain the previous ID and
signal the error.
Default: 1
For a vertical installation, the ID number must be within the range of 1 to 4. For a horizontal installation, the ID number
must be within the range of 129 to 144.
If the type of installation is changed (from vertical to horizontal or vice versa), the ID will no longer be valid (value
indicated as 0) and must be reconfigured.
Switchboard ID ID setting

17
VIMAR group
7” Due Fili Plus porter switchboard
ID verification Confirm ID
• Language
Use the keys and to select the desired language. Press to confirm or press to cancel
without saving.
Default: Italian.
Language Language selection
• Date format
Use the keys and to select the desired date display format. Press to confirm or press to
cancel without saving.
Date format

18
7” Due Fili Plus porter switchboard
• Time format
Use the keys and to select the desired time display format. Press to confirm or press to
cancel without saving.
Time format
• Standby cut-in time
Use the keys and to select the period of inactivity after which the switchboard will switch to stand-by
mode. Press to confirm or press to cancel without saving.
Default: 10 seconds.
Standby time
• Numbering plan
Use the keys and to select the numbering plan, choosing between: natural, 4-digit (available for vertical
installation only) and 8-digit. Press to confirm or press to cancel without saving.
Default: natural.
For further details, refer to the paragraph "4- or 8-digit Numbering".

19
VIMAR group
7” Due Fili Plus porter switchboard
Numbering plan Natural
4-digit 8-digit
• Horizontal or vertical installation
Use the keys and to select vertical or horizontal installation type. Press to confirm or press
to cancel without saving.
Default: vertical.
Whenever this parameter setting is changed, the switchboard ID will no longer be valid (status indicated by ID 0),
and will have to be reconfigured.
Furthermore, if the installation type is changed from vertical to horizontal and the current numbering plan is 4-digit,
this will automatically be changed to 8-digit, as the 4-digit plan is not compatible with a horizontal installation.
Horizontal/Vertical installation

20
7” Due Fili Plus porter switchboard
Vertical Horizontal
• Reset of all parameters to default factory settings
Press to start the procedure to reset the switchboard configuration. The reset confirmation screen is displayed
(see below): press to proceed or to cancel and maintain the current configuration.
The reset does not affect contacts lists and event lists, which will be retained in the device memory.
Reset default factory settings Reset confirmation request
• Installer PIN
Press to start the procedure to change the installer PIN (required to access to the advanced settings menu).
In the next screen, enter four digits. Press to confirm or press to cancel without saving.
Default: 1234.
Installer PIN PIN setting