Emerson Bettis RTS FQ Series User manual

User Instructions
MAN-02-04-60-0351-EN Rev. 3
February 2019
Operating Manual for Bettis RTS FQ Series
Fail-Safe Quarter-Turn Electric Actuator

i
User Instructions
MAN-02-04-60-0351-EN Rev. 3
Table of Contents
February 2019
Table of Contents
Table of Contents
Section 1: Introduction
Section 2: Functional Description of the
RTS FQ Fail-Safe Quarter-Turn Actuator
Section 3: General
3.1 Safety Instructions ........................................................................................ 4
3.2 Serial Number ............................................................................................... 4
3.3 Protection Class ............................................................................................ 4
3.4 Mounting Position......................................................................................... 5
3.5 Direction of Rotation..................................................................................... 5
3.6 Protective Devices......................................................................................... 6
3.7 Ambient Temperature................................................................................... 6
3.8 Delivery Condition of the Actuators .............................................................. 7
3.9 Information Notice (Tag) ............................................................................... 7
Section 4: Transport and Storage
4.1 General ......................................................................................................... 8
4.2 Storage ......................................................................................................... 8
4.3 Long-term Storage........................................................................................ 9
Section 5: Installation Instructions
5.1 Mechanical Connection............................................................................... 10
5.2 Mounting Position of the Control Unit......................................................... 11
5.3 Electrical Connection .................................................................................. 11
Section 6: Commissioning
6.1 General Information.................................................................................... 14
6.2 Manual Operation ....................................................................................... 14
6.3 Mechanical Default Settings, Preparation.................................................... 14
6.4 End Limit Setting......................................................................................... 15
6.5 Setting the Mechanical End Stop................................................................. 22
6.6 Adjusting of Fail-Safe Speed ........................................................................ 24
6.7 Final Step .................................................................................................... 25
Section 7: Control Unit
7.1 Operating Unit ............................................................................................ 26
7.2 Display Elements......................................................................................... 27
7.3 Operation ................................................................................................... 29

ii
User Instructions
MAN-02-04-60-0351-EN Rev. 3
Table of Contents
February 2019
Table of Contents
Section 8: Parameter Menu
8.1 Parameter Group: End Limit ........................................................................ 37
8.2 Parameter Group: Torque............................................................................ 39
8.3 Parameter Group: Speed ............................................................................. 40
8.4 Parameter Group: Ramp (optional) ............................................................. 40
8.5 Parameter Group: Control ........................................................................... 41
8.6 Parameter Group: Password ........................................................................ 41
8.7 Parameter Group: Position .......................................................................... 42
8.8 Parameter Group: Binary Inputs .................................................................. 42
8.9 Parameter Group: Binary Outputs ............................................................... 45
8.10 Parameter Group: Position Output (optional).............................................. 48
8.11 Parameter Group: Step Mode ...................................................................... 50
8.12 Parameter Group: Positioner (optional)....................................................... 52
8.13 Parameter Group: PID Controller (optional)................................................. 55
8.14 Parameter Group: Bus Systems (optional) ................................................... 56
8.15 Parameter Group: Characteristic Curves (optional)...................................... 57
8.16 Parameter Group: Identication (optional) .................................................. 58
8.17 Parameter Group: System Parameters (locked) ........................................... 58
8.18 Parameter Group: Miscellaneous................................................................. 59
Section 9: Status Area
9.1 Status.......................................................................................................... 60
9.2 History........................................................................................................ 63
Section 10: Infrared Connection
Section 11: Bluetooth Connection
Section 12: Maintenance
Section 13: Troubleshooting
13.1 Error List...................................................................................................... 69
Section 14: Fuses

iii
User Instructions
MAN-02-04-60-0351-EN Rev. 3
Table of Contents
February 2019
Table of Contents
Section 15: Lubricant Recommendation and Requirements
15.1 Main Body: -25 to +60C............................................................................... 72
15.2 Main Body: -40 to +60C............................................................................... 72
15.3 Output Type A and Spindle Drives (Linear Actuators) -40 to +60C................ 72
15.4 Basic Lubricant Service Interval ................................................................... 72
Section 16: Training
Section 17: Technical Data and Certifications
17.1 Binary Outputs............................................................................................ 75
17.2 Binary Inputs............................................................................................... 76
17.3 Analog Inputs.............................................................................................. 80
17.4 Analog Output ............................................................................................ 80
17.5 Auxiliary Voltage Input and Output ............................................................. 82
17.6 Connections ............................................................................................... 83
17.7 Miscellaneous ............................................................................................. 83

1
Section 1: Introduction User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Introduction
Section 1: Introduction
NOTE:
Also refer to the operating manual for Bettis RTS CM Compact Multi-Turn Series.
Bettis RTS FQ Fail-Safe Quarter-Turn electric actuators are designed to operate appropriate
ttings when a fail-safe functionality is required.
Appropriate ttings are all kinds of ttings that require a 90
o
movement to operate
(buttery valves, ball valves, taps in general, etc.).
In the event of a power failure or if the fail-safe function is triggered deliberately, the
actuator shifts the tting to the fail-safe position, using the built-in energy storage device
to do so.
Figure 1 Bettis RTS FQ Fail-Safe Quarter-Turn Actuator

2
Section 2: Functional Description of the RTS FQ Fail-Safe Quarter-Turn ActuatorUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
Functional Description of the RTS FQ Fail-Safe Quarter-Turn Actuator
Section 2: Functional Description of the
RTS FQ Fail-Safe Quarter-Turn
Actuator
In normal operation, the actuator is operated by a PM motor (1) via a worm gear stage (2)
and a planetary gear train (3). The motor drives the spindle nut of a ball screw (4). The sun
gear shaft of the planetary gear train is xed in place by an operating current brake (5).
The ball screw converts the rotational movement of the gear unit into linear motion, which,
on the other hand, charges the spring assembly (7), which acts as an energy storage device.
On the other hand, a rack and pinion gear (6) converts the linear motion into the 90
o
output motion to move the tting shaft (9).
There are no engaging or disengaging elements between the motor. The energy storage device
and the tting shaft in the actuator. All the gear unit components are permanently engaged.
While moving against the fail-safe direction, the electric motor has to move both the tting
and the energy storage device (disk spring assembly) for the fail-safe stroke.
If the supply for the operating current brake is interrupted by a power failure, or intentionally
triggers a fail-safe stroke, the actuator will no longer hold position, and the energy stored in
the disk spring assembly will be converted into kinetic energy so as to move the actuator and
thus the tting to the fail-safe position. In this situation, the entire gear chain for the actuator
with the exception of the worm gear stage will be moved until the adjustable mechanical end
stop (8) is reached or, if applicable, be stopped for the tting.
Owing to this operating principle, neither an initializing stroke nor resetting of the drive
is required after a fail-safe stroke. As soon as the power supply is restored, the actuator is
immediately ready for operation.
Figure 2 Cut-out of the RTS FQ Fail-Safe Quarter-Turn Actuator

3
Section 2: Functional Description of the RTS FQ Fail-Safe Quarter-Turn Actuator User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Functional Description of the RTS FQ Fail-Safe Quarter-Turn Actuator
Parts Overview:
1. PM Motor
2. Worm Gear Stage
3. Planetary Gear Train
4. Ball Screw
5. Operating Current Brake
6. Rack and Pinion Gear
7. Spring Assembly
8. End Stop
9. Fitting Shaft
This compact fail-safe actuator can be built as a version for “fail-safe open” (counter
clockwise direction of rotation when looking at the tting shaft) or “fail-safe close”
(clockwise direction of rotation). It is even possible to subsequently change the fail-safe
direction (separate manual available). Some assembly work is required. Having this
conversion performed at our factory is recommended, however.
Figure 3 Fail-Safe Open Version
Fail-safe
Direction
F
ail-sa
f
e
Direction
Direction
Figure 4 Fail-Safe Close Version
Fail-safe
Direction

4
Section 3: GeneralUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
General
Section 3: General
3.1 Safety Instructions
CAUTION: FOLLOW SAFETY INSTRUCTIONS
When operating electrical devices, certain parts are inevitably under dangerous voltage.
Work on the electrical systems or components may only be carried out by electricians or by
individuals who have been instructed how to do so, working under the guidance and
supervision of an electrician in accordance with electrotechnical regulations.
WARNING: ALWAYS REFER TO STANDARDS
When working in potentially explosive areas, refer to European Standards EN 60079-14
“Installing Electrical Systems in Explosion Endangered Areas” and EN 60079-17 “Inspection and
Maintenance of Electrical Installations in Explosion Endangered Areas”.
Working in potentially explosive areas is subject to special regulations (European Standard EN
60079-17), which must be complied with. Any additional national regulations must be heeded.
CAUTION: ALWAYS BE AWARE OF DANGER TO EXPLOSION
Work on the open actuator under voltage may only be done if it is certain that there is no
danger of explosion for the duration of the work.
3.2 Serial Number
Each actuator of the Bettis RTS FQ Series carries a serial number. The serial number is a
10-digit number that begins with the year and that can be read from the type label
(see Figure 3) the type label is located next to the handwheel).
Using this serial number, Bettis can uniquely identify the actuator (type, size, design,
options, technical data and test report).
3.3 Protection Class
Bettis RTS FQ Fail-Safe Quarter-Turn actuators come by default with IP 68
(EN 50629) protection.
CAUTION:
The protection class specied on the type label is only effective when the cable glands also
provide the required protection class, the cover of the connection compartment
is carefully secured closed, and the mounting position (see Section 3.4) is observed.

5
Section 3: General
5
User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
General
We recommend metallic threaded cable glands with a metrical thread. Unused, cable
inlets must be closed with stopping plugs. On explosion-proof actuators, cable glands with
protection class EEx e according EN60079-7 must be used. After removing covers for
assembly purposes or adjustment work, take special care upon reassembly so that seals are
not damaged and remain properly fastened. Improper assembly may lead to water ingress
and to failures of the actuator.
NOTE:
The cover of the control unit - the Operating unit - (see Figure 1) must not be opened.
Allow a certain sag in the connector cables before reaching the screwed cable glands so that
water can drip off from the connector cables without running to the screwed cable glands.
As a result, forces acting on the screwed cable glands are also reduced. (see Section 3.4)
3.4 Mounting Position
Generally, the installation position is irrelevant. However, based on practical experience,
it is advisable to consider the following for outdoors use or in splash zones:
• Mount actuators with cable inlet facing downwards.
• Ensure that sufcient cable slack is available.
3.5 Direction of Rotation
CAUTION: OBSERVE DIRECTION OF ROTATION
The standard direction of rotation for the actuator is:
• Clockwise = The actuator runs counter to the fail-safe direction
• Counterclockwise = The actuator runs in the fail-safe direction
Which direction, opening or closing of the tting causes, depends on:
• The fail-safe direction of the actuator
• The closing direction of the tting
All the information in this Operating Manual refers to the standard direction of rotation.

6
Section 3: GeneralUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
General
3.6 Protective Devices
3.6.1 Torque
Bettis RTS FQ Fail-Safe Quarter-Turn actuators provide electronic torque monitoring.
The switch-off torque can be modied in the controller menu for each direction separately.
By default, switch-off torque is set to the ordered value. If no torque was specied with the
order, the actuator is supplied from the factory with the maximum congurable torque.
For more information, see Section 8.1.
3.6.2 Motor Temperature
All ACTUSMART CM actuators are normally equipped with motor winding temperature
sensors, which protect the motor against excessive winding temperature.
The display will show the corresponding error upon exceeding the permissible motor
temperature, see Section 13.1.
3.6.3 Input Fuse, Thermal Fuse
The frequency inverter is protected by an input fuse and the explosion proof version by a
thermal fuse. If one of the fuses releases, a serious defect occurs and the frequency inverter
must be replaced.
3.7 Ambient Temperature
Unless otherwise specied upon ordering, the following operating temperatures apply:
• On/Off duty (open-loop control) -25 to +60C
• Modulating duty (closed-loop control) -25 to +60C
• Explosion-proof version -20 to +40C (acc. EN 60079-0)
• Explosion-proof version with extended temperature range -40 to +60C

7
Section 3: General User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
General
3.8 Delivery Condition of the Actuators
For each actuator, an inspection report is generated upon nal inspection. In particular, this
comprises a full visual inspection, calibration of the torque measurement in connection
with an extensive run examination and a functional test of the microcontrollers.
These inspections are conducted and documented according to the quality system and can
be made available if necessary.
The basic setting of the end position must be performed after assembly on the actuator.
CAUTION
Commissioning instructions (see Section 5, page 25) must be strictly observed!
During assembly of the supplied valves at the factory, end postions are set and
documented by attaching a label (see Bild 16). During commissioning at the plant,
these settings must be veried.
3.9 Information Notice (Tag)
Each actuator is provided with a bilingual tag containing key information, which is attached
to the handwheel after nal inspection. This tag also shows the internal commission
registration number (see Figure 5).
Figure 5 Tag

8
Section 4: Transport and StorageUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
Transport and Storage
Section 4: Transport and Storage
Depending on the order, actuators may be delivered packed or unpacked. Special
packaging requirements must be specied when ordering. Please use extreme care when
removing or repackaging equipment.
CAUTION: USE APPROPRIATE LIFTING EQUIPMENT
Use soft straps to hoist the equipment; do not attach straps to the handwheel.
If the actuator is mounted on a valve, attach the straps to the valve and not to the actuator.
4.1 General
The connection compartment of RTS Compact Multi-Turn CM actuators contains 5g of
factory supplied silica gel.
CAUTION: REMOVE SILICA GEL
Please remove the silica gel before commissioning the actuator (see Section 5).
4.2 Storage
CAUTION: OBSERVE PROPER STORAGE
- Store actuators in well-ventilated, dry premises
- Protect against oor dampness by storing actuators on wooden grating, pallets,
mesh boxes or shelves
- Protect the actuators against dust and dirt with plastic wrap
- Actuators must be protected against mechanical damage
- The storage temperature must be between -20°C - +40°C
It is not necessary to open the controller of the actuator for servicing batteries or
similar operations.

9
Section 4: Transport and Storage User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Transport and Storage
4.3 Long-term Storage
CAUTION: 6 MONTHS OF STORAGE
If you intend to store the actuator for over 6 months, also follow the instructions below:
- The silica gel in the connection compartment must be replaced after 6 months of
storage (from date of delivery)
- After replacing the silica gel, brush the connection cover seal with glycerine.
Then, carefully close the connection compartment again
- Coat screw heads and bare spots with neutral grease or long-term
corrosionprotection
- Repair damaged paintwork arising from transport, improper storage,
or mechanical inuences
- For explosion-proof actuators, it is not allowed to extensively overpaint the actuator.
According to the standard, in order to avoid electrostatic charge, the maximum
thickness of the varnish paint is limited to 200 µm.
- Every 6 months. all measures and precautions for long term storage must be
checked for effectiveness and corrosion protection and silica gel renewed
- Failure to follow the above instructions may lead to condensation which can damage
to the actuator

10
Section 5: Installation InstructionsUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
Installation Instructions
Section 5: Installation Instructions
Installation work of any kind for the actuator may only be performed by qualied personnel.
5.1 Mechanical Connection
Check:
• Whether the tting ange and actuator ange match-up.
• Whether the drilled hole matches up with the shaft.
• Whether there is sufcient engagement of the tting shaft in the actuator hole.
Make sure the tting is in the same position as the actuator:
• For a “fail-safe opener” actuator, the tting has to be completely open.
• For a “fail-safe closer” actuator, the tting has to be completely closed.
In general, heed the following instructions:
• Clean the bare parts on the actuator coated with rust protectant.
• Clean the mounting surface for the tting thoroughly.
• Lightly grease the tting shaft.
• Set the actuator in place.
• Make sure of centered positioning and that the contact surface of the ange is full.
• Fasten the actuator with suitable bolts:
— Minimum strength grade: 8.8 or A2-70
— Ensure sufcient thread engagement (min. 1xd)
CAUTION: USE SUITABLE BOLTS
Screws that are too long may go against the thread root, creating the risk of the actuator
moving radially in relation to the tting. This may lead to the bolts shearing off.
Unsuitable bolts may result in the actuator falling off.
• Tighten bolts to the correct torque, alternating between bolts on opposite sides.
Table 1. Torque Thread Table (1)
Thread Tightening Torque [Nm] for Bolts with Strength Grade
8.8 A2-70/A4-70
M6 11 8
M8 25 18
M10 51 36
M12 87 61
M16 214 150
M20 431 294
M30 1489 564

11
Section 5: Installation Instructions User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Installation Instructions
5.2 Mounting Position of the Control Unit
The mounting postion of the operating unit can be rotated in 90 steps.
Figure 6
-90° +90°
+180°
• Disconnect the actuator and control system from the power supply.
• To prevent damage to the electronic components, both the control system and
the person have to be grounded.
• Undo the bolts for the interface surface and carefully remove the service cover.
• Turn service cover to new position and put back on.
— Ensure correct position of the O-ring.
— Turn service cover by maximum of 180o.
— Put service cover on carefully so that no cables get wedged in.
• Tighten bolts evenly in a crosswise sequence.
5.3 Electrical Connection
Electrical connections may only be carried out by qualied personnel. Please observe
all relevant national security requirements, guidelines and regulations. The equipment
should be deenergized before working on electrical connections. As a rst step connect the
ground screw and conrm the absence of electrostatic discharge during connection.
The line and short circuit protection must be done on the system side. The ability to unlock
the actuator is to be provided for maintenance purposes. For the dimensioning, the rated
current is to be used (see Technical Data).
Check whether the power supply (voltage, frequency) is consistent with the connection
data (see nameplate - Figure 5). The connection of electrical wiring must follow the circuit
diagram. This can be found in the appendix of the documentation. The circuit diagram can
be ordered from Emerson by specifying the serial number. When using options, such as a
Probus connection, the relevant guidelines must be followed.

12
Section 5: Installation InstructionsUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
Installation Instructions
5.3.1 Power Supply Connection
RTS CM Compact Series actuators feature an integrated motor controller, i.e., it only
requires a connection to the power supply. By non-explosionproof actuators the wiring
uses a connector independent from control signals (see Figure 7).
Figure 7 Power Supply Connections
1
2
3
4
5
6
7
8
Parts Overview:
1. Metric Screw M32x1.5
2. M40x1.5
3. M25x1.5
4. Plug Insert (for power supply)
5. Plug Insert (for control cables)
6. Connector for Options
7. Connector Plate
8. Connecting Housing
Explosionproof actuators or on special request the connection will be made via terminals
(see Figure 6).

13
Section 5: Installation Instructions User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Installation Instructions
Figure 8 Terminal Box
Parts Overview:
1. Metric Screw M40x1.5
2. 2xM20x1.5
3. Terminals for the Control Signals
4. Terminals for the Power Supply
5. Terminal for Ground Connection
6. Outside Ground Connection
CAUTION: OBSERVE CORRECT PROCEDURE
See Section 14.3.

14
Section 6: CommissioningUser Instructions
MAN-02-04-60-0351-EN Rev. 3 Febraury 2019
Commissioning
Section 6: Commissioning
It is assumed that the actuator has been installed and electrically connected correctly.
(See Section 5).
NOTE:
Remove silica gel from the alarm cover.
6.1 General Information
NOTE:
When commissioning and each time after dismounting the actuator, the positions have to
be reset (see Section 6.4).
6.2 Manual Operation
There is no way to operate this actuator design manually.
6.3 Mechanical Default Settings, Preparation
The use of multi-turn sensors makes mechanical settings unnecessary.
CAUTION: OBSERVE CORRECT PROCEDURE
Before the motorised operation of the valve, it is essential to check and adjust
torque settings.

15
Section 6: Commissioning User Instructions
MAN-02-04-60-0351-EN Rev. 3February 2019
Commissioning
6.4 End Limit Setting
A detailed description of the operation of the RTS CM Compact Series controller can be
found in Section 7.3.
6.4.1 End Limit OPEN
Step 1 - Set the selector switch and control switch to the center position.
Figure 9 Selector/Control Switch
1
2
Parts Overview:
1. Selector Switch (red)
2. Control Switch (black)
Step 2 - Scroll through the menu with the control switch. Move the control switch towards
the rst menu item "P1.1 End limit – Open".
Figure 10 Control Switch (First Menu Item)