Emerson Fisher FIELDVUE DVC6200 SIS Configuration guide

www.Fisher.com
Fisher™FIELDVUE™DVC6200 SIS Digital Valve
Controller PST Calibration and Testing using
ValveLink™Software
The test procedure contained in this Instruction Manual Supplement is to be considered as a guideline only and should
be modified to address site‐specific requirements. Use this procedure in conjunction with the DVC6200 Series quick
start guide (D103556X012) and the DVC6200 SIS instruction manual (D103557X012). In addition, exercise good
engineering practices and abide by specific plant safety guidelines for safe operation.
WARNING
This document is not intended to be used as a stand‐alone document. It must be used in conjunction with the following
documents:
Safety Manual for FIELDVUE DVC6200 SIS Digital Valve Controller and Position Monitor (D103601X012)
Fisher FIELDVUE DVC6200 SIS Instruction Manual (D103557X012)
Failure to use this instruction manual supplement in conjunction with the above referenced manuals could result in
personal injury or property damage. If you have any questions regarding these instructions or need assistance in obtaining
any of these documents, contact your Emerson sales office.
For additional information on Partial Stroke Testing and associated parameters refer to Partial Stroke Test Information
on page 19.
Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
2
PST Calibration
This document covers the basic PST calibration, as well as details for making adjustments to the normal end, using
Advanced Settings (see figure 11).
Figure 1. Calibration > Partial Stroke
Confirm SIS Tier

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
3
Figure 2. Set Instrument Out of Service and start Partial Stroke Test calibration
Refer to figure 11 for
information on Advanced
Settings

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
4
Figure 3. Enter the Desired Outgoing Ramp Rate
Supports separate ramp
rates for outing and
incoming strokes
Figure 4. Enter the Desired Incoming Ramp Rate
Additional ramp
rates for the
incoming stroke

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
5
Figure 5. Enter the Travel Target Movement
Target Travel Movement is the
percentage of travel from the
normal end
Figure 6. Partial Stroke Calibration progress

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
6
Figure 7. Partial Stroke Calibration progress
Will calibrate to 30% from
the normal end
Figure 8. Configuring SIS Triggers

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
7
Figure 9. Partial Stroke Calibration Progress
Figure 10. Calibration Procedure Complete
List of parameter values
being downloaded to the
device
If you need to make adjustments to the normal end default settings, select Advanced Settings, as shown in figure 11,
and make the necessary adjustments.

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
8
Figure 11. Select Advanced Settings to Make Adjustments to the Normal End
Select to define the
normal end
Figure 12. Set Travel High End
Defines the normal end of travel
(where the valve is when the
process is running normally)
The point at which valve
seating occurs will vary slightly
every time. Do not set this
higher than 99.5% or lower
than 0.5%.

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
9
Figure 13. Enter Target Travel Movement
Figure 14. Partial Stroke Calibration Progress
Running a PST calibration will enable Short Duration PST. If this is not desired, refer to figure 24 for information on
disabling Short Duration PST.

Instruction Manual Supplement
D104299X012
DVC6200 SIS
October 2018
10
Configuration
After successfully calibrating the valve for PST go to the Detailed Setup SIS/Partial Stroke tab and verify the values for
the parameters in the Test Configuration group box are correct. Then go to the SIS Options group box and enable any
of the behaviors required for the PST.
Figure 15. Verify Test Configuration and Test Acceptance Criteria