Emerson ATHENIAN CF2400AB00 User manual

READ AND SAVE THESE INSTRUCTIONS
Model No.
CF2400AB00
CF2400BC00
CF2400ORB00
CF2400PW00
CF2400SCK00
CF2400WB00
ATHENIAN™
Part No. F40BP72780000 Form No. BP7278
®
Net Weight: 21.6 Lbs.
Ceiling Fan
Owner's Manual
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of
the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price
of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OR
REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF
OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson
Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort
Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any defects, malfunctions or failures
caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee,
agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE
FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages
as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if
this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

2
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local
Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in
doubt.
4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not
know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution of
parts or accessories not designated for use with this product by Emerson Electric Co. could result in
personal injury or property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING
!
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.

Tools Needed for Assembly
One Phillips head screwdriver One wire stripper
Three wire connectors (supplied) One stepladder
Four T8 25-watt (max.) candelabra base bulbs (supplied)
MATERIALS
Wiring, outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the following
sizes:
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is
completed, place a check mark in the box. This will insure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
a. Fan motor and housing assembly
b. One motor cover
c. Once ceiling cover
d. Five blade flanges
e. One hanger bracket
f. One hanger ball/downrod assembly
g. One switch housing cover
h. One cover plate
i. One finial nut
j. One uplight lead assembly (used only for
remote control operation)
k. Four T8 25-watt candelabra base bulbs
l. One loose parts bag containing:
1. One 5/16-18 x 1/4” setscrew
2. One setscrew wrench
3. Two 1” threaded studs
4. Two 1-1/4” threaded studs
5. Four knurled knobs
6. Four lockwashers
7. Four wire connectors
8. Two pull chain pendants 3
9. Two couplings
10. One hairpin clip
11. One clevis pin
12. Eleven 10-32 x 5/8” oval head screws
13. Sixteen 10-32 x 3/8” Phillips pan head
screws
14. Sixteen #10 flat washers
15. Three 8-32 x 3/8” pan head screws
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 7). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
FAN MOTOR
AND HOUSING
ASSEMBLY
BLADE
FLANGES
FINIAL
NUT
HANGER
BRACKET
SWITCH
HOUSING
COVER
HANGER BALL/
DOWNROD
ASSEMBLY
LOOSE
PARTS
BAG
COVER
PLATE
CEILING
COVER
MOTOR
COVER

1. Remove the fan motor and housing assembly from
the styrofoam packaging and position it so that the
top of the motor is facing you.
2. Remove the hanger ball from the downrod by
loosening the setscrew in the hanger ball until the
ball falls freely down the downrod (Figure 1).
Remove the pin from the downrod, then remove
the hanger ball. Retain the pin and hanger ball for
reinstallation in step 8.
3. Separate, untwist and unkink the three motor
leads. Route the motor leads through the downrod
and seat the downrod in the motor coupling (Figure
2).
PIN
HANGER
BALL
SETSCREW
DOWNROD
Figure 1
4
Electrical Requirements How to Assemble Your
Ceiling Fan
Uplight
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
To avoid possible fire or shock, follow all wiring
instructions carefully.
Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
WARNING
!
The Emerson CF2400 Series Ceiling Fan is designed
to be operated from wall switch(es), from an Emerson
remote control/transmitter, or from Emerson fan/light
controls. There are no controls supplied with the
ceiling fan.
Your ceiling fan is supplied with a built-in uplight in the
motor housing. This uplight has a pull chain switch in
the switch housing to turn it ON or OFF. A separate
switch may be used to operate the uplight. This will
require a three-wire (with ground) conductor cable
between the ceiling and wall outlet boxes.
IMPORTANT: If you are going to use an Emerson
remote control and receiver to control your fan,
perform the instructions in this Owner’s Manual in
conjunction with the instructions contained in the
remote control/receiver Owner’s Manual.
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
HAIRPIN
CLIP
CLEVIS
PIN
MOTOR COUPLING
MOTOR LEADS
DOWNROD
SETSCREW
CLEVIS
PIN
Figure 2

5
4. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 2). (Pin and
clip are supplied in loose parts bag.) The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod. Push the straight leg
of the hairpin clip through the hole near the end of
the clevis pin until the curved portion of the hairpin
clip snaps around the clevis pin. The hairpin clip
must be properly installed to prevent the clevis pin
from working loose. Pull the hanger ball to make
sure the clevis pin is properly installed.
5. Install the setscrew (supplied) in the motor coupling
(Figure 2). While pulling up on the downrod, tighten
the setscrew using the setscrew wrench (supplied).
NOTE: The setscrew must be properly installed as
described above, or fan wobble could result.
6. Screw two 1” threaded studs (supplied) into the
motor (Figure 3). Leave approximately 7/8” of the
stud extending above the motor. Coil the wires and
wire connectors around the motor coupling then
slide the motor cover over the downrod and rotate
the cover until the threaded studs protrude. Install
two lockwashers (supplied) to secure the cover to
the motor. All wires and wire connectors must be
enclosed under the motor cover.
NOTE: Lightly snug the knurled knobs and make
sure the wires and wire connectors are
completely inside the motor coupling cover and
not pinched between the motor coupling cover
and the motor.
7. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 4).
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed (as shown in Figure 2) could
result in the fan falling.
WARNING
!
LOCKWASHER (2)
KNURLED
KNOB (2)
MOTOR
COUPLING
MOTOR COVER
1" THREADED
STUD (2)
Figure 3
8. Reinstall the hanger ball on the downrod (Figure 4)
as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod. Install the pin through the holes at the top
of the downrod and slide the hanger ball up the
downrod, aligning the ball so the pin in captured in
the groove in the top of the hanger ball. Pull the
hanger ball up tight against the pin and securely
tighten the setscrew in the hanger ball. A loose
setscrew could create fan wobble.
9. The fan comes with blue, black and white leads
that are 80-inches long. Before installing the fan,
measure up approximately 6 to 9-inches above
top of hanger ball/downrod assembly. Cut off
excess leads and strip back insulation 1/2-inch
from end of leads.
10. Use three 10-32 x 3/8” Phillips pan head screws
(supplied) and three #10 flat washers to secure
the fan blade to the blade flange (Figure 5).
Repeat this procedure for the remaining four
blades.
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
CEILING
COVER
DOWNROD
PIN HANGER BALL
SETSCREW
Figure 4
10-32 x 3/8" PHILLIPS
PAN HEAD SCREWS (3)
#10 FLAT WASHERS (3)
FAN BLADE
BLADE FLANGE
Figure 5

11. Use the 10 round recessed holes in the motor hub
that are marked with a “5” and install the five
blade assemblies in accordance with Step 12.
One side of the switch housing has been indented
to allow easy access when installing the flange
screws.
12. Attach one blade assembly to the motor hub
using two 10-32 x 5/8” oval head screws
(supplied) (Figure 6). Do not tighten completely at
this time. Install four remaining blade assemblies
in the same way. Gently snug all flange screws to
the motor hub, working around the hub in a
clockwise sequence. Next, securely tighten all
flange screws, again working in a clockwise
sequence. Failure to follow this procedure could
result in fan wobble. This completes the blade
installation.
6
BLADE FLANGE
5
5
4
MOTOR
HUB SWITCH
HOUSING 10-32 x 5/8" OVAL HEAD
SCREWS (2 per blade assmebly)
Figure 6
How to Hang
Your Ceiling Fan
CEILING
FLOOR
AT LEAST
7'
Figure 7
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 7).
WARNING
!
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
Figure 8
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 9).
Be sure the groove in the ball is lined up with the
tab on the hanger bracket (Figure 8).
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.
WARNING
!
To reduce the risk of personal injury, do not bend the
blade flanges when installing the flanges, balancing
the blades, or cleaning the fan. Do not insert foreign
objects between rotating fan blades.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
1. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box. (Figure 8.)
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD
ASSEMBLY
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
THREADED
STUD (2)
Figure 9
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
7
How to Wire Your
Ceiling Fan
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
1. If you are going to use an Emerson Remote
Control/Receiver or Wall Control/Receiver to
operate your ceiling fan, wire your fan in
accordance with the Control/Receiver
Owner’s Manual. (NOTE: The wire from the
uplight harness is orange instead of yellow.)
After wiring, return to Step 4 below.
2. If you are going to use two wall switches or
Emerson Fan/Light Controls, you will need a
three-wire (with ground) conductor cable
between the ceiling and wall outlet boxes.
This will allow you to operate the uplight and
optional Emerson Light Fixture (if installed)
from one switch/control and the ceiling fan
from a separate switch/control. (Refer to the
Emerson Fan/Light Control Owner’s Manual.)
Refer to Figure 10 and proceed as follows:
a. Connect the green grounding lead from
the hanger ball and the green grounding
lead from the hanger bracket to the
supply grounding conductor (this may be
a bare wire or wire with green colored
insulation). Securely connect wires with a
wire connector (supplied).
b. Securely connect the fan motor white wire
to the supply white (neutral) wire using a
wire connector (supplied).
c. Securely connect the fan motor black wire
to the supply black (hot) wire using a wire
connector (supplied).
d. Securely connect the fan motor blue wire
to the supply red (hot) wire using a wire
connector (supplied).
e. After connections have been made,
separate the white and green wires from
the black, blue and red wires.
f. Carefully turn the wires upward and insert
them up through the open side of the
hanger bracket and into the outlet box.
Push the green and white wires into
one side of the outlet box; push the black,
blue and red wires into the other
side of the outlet box.
3. If you are going to use a single wall switch to
control your ceiling fan, uplight, and optional
Emerson Light Fixture (if installed)
simultaneously, you will need a standard
two-wire (with ground) conductor cable
between the ceiling and wall outlet boxes.
The fan speed and uplight can then be
operated from the pull chain switches in the
switch housing; the optional light fixture can
be operated from the light fixture switch.
Refer to Figure 11 and proceed as follows:
a Connect the green grounding lead from
the hanger ball and the green grounding
lead from the hanger bracket to the
supply grounding conductor (this may be
a bare wire or wire with green colored
insulation). Securely connect wires with a
wire connector (supplied).
b. Securely connect the fan motor white wire
to the supply white (neutral) wire using a
wire connector (supplied).
c. Securely connect the fan motor black
wire and blue wire to the supply black (hot)
wire using a wire connector (supplied).
d. After connections have been made,
separate the white and green wires from
the black and blue wires.
e. Carefully turn the wires upward and insert
them up through the open side of the
hanger bracket and into the outlet box.
Push the green and white wires into one
side of the outlet box; push the black and
blue wires into the other side of the outlet
box.
BLACK BLACK FAN WIRE
LISTED OUTLET BOX
LIGHT
CONTROL
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET TO 120
VOLT
SUPPLY
WHITE
GROUND
GREEN WIRE (GROUND)
FROM HANGER BALL
GROUND
WIRE WHT.
EMERSON FAN CONTROL
BLACK
(HOT)
BLUE
RED
GROUND
THREE-CONDUCTOR CABLE (WITH
GROUND) BETWEEN CEILING AND
WALL OUTLET BOXES
LISTED WIRE CONNECTOR (4)
Figure 10
BLACK FAN WIRE
LISTED OUTLET BOX GENERAL USE
ON/OFF
WALL SWITCH
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET TO 120
VOLT
SUPPLY
WHITE
GROUND
GREEN WIRE (GROUND)
FROM HANGER BALL
GROUND
WIRE WHT.
BLACK
(HOT)
BLUE
BLACK
GROUND
TWO-CONDUCTOR CABLE (WITH
GROUND) BETWEEN CEILING AND
WALL OUTLET BOXES
LISTED WIRE CONNECTOR
(
3
)
Figure 11
Check to see that all connections are tight,
including ground, and that no bare wire is visible
at the wire connectors, except for the ground wire.
Do not operate fan until blades are in place. Noise
and fan damage could result.
WARNING
!
Check to see that all connections are tight,
including ground, and that no bare wire is visible
at the wire connectors, except for the ground wire.
Do not operate fan until blades are in place. Noise
and fan damage could result.
WARNING
!

8
4. Screw the two 1-1/4” threaded studs (supplied) into
the tapped holes in the hanger bracket
(Figure 9).
5. Lift the ceiling cover up to the threaded studs and
turn until the studs protrude through the holes in
the ceiling cover (Figure 12).
6. Secure the ceiling cover in place by sliding
lockwashers (supplied) over the threaded studs
and installing the two knurled knobs (supplied).
(Figure 12.) Tighten the knurled knobs securely
until the ceiling cover fits snugly against the ceiling.
7. Screw in four T8 25-watt (maximum) candelabra
base bulbs (supplied) into the uplight sockets on
top of the fan housing assembly.
8. Position the cover plate on the switch housing
cover (Figure 13) and secure in place by installing
the finial nut finger tight.
NOTE: If you are going to install an Emerson
accessory light kit, do not install the finial nut and
cover plate. Instead, install the switch housing
cover on the light kit in accordance with the
Emerson light kit Owner’s Manual.
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
!
CEILING
COVER
THREADED
STUDS (2)
KNURLED
KNOB (2)
LOCKWASHER (2)
Figure 12
SWITCH
HOUSING
COVER
COVER PLATE
FINIAL NUT
Figure 13
8-32 x 3/8"
PAN HEAD
SCREWS (3)
SWITCH HOUSING
COVER
Figure 15
9. Position the switch housing cover so that the tab on
the inside of the switch housing cover aligns with
the notch in the switch housing (Figure 14). With
the switch housing cover held in this position,
pass the shortest pull chain through the nearest
bushing.
10. Attach the smaller pendant to the smallest pull
chain using a coupling (Figure 14). Pass the
longer pull chain through the other bushing;
attach the largest pendant to this pull chain using
a coupling.
11. Position the switch housing cover over the switch
housing and rotate slightly until the tab in the
cover engages with the notch in the switch
housing. Install three 8-32 x 3/8” pan head screws
to secure the cover in place (Figure 15).
SWITCH
HOUSING
COVER
PENDANT
COUPLING
TAB
PENDANT
COUPLING VIEW "A"
BUSHING
SWITCH
CHAIN
SWITCH
HOUSING NOTCH
SEE VIEW
"A"
Figure 14

9
Maintenance
Using Your Ceiling Fan Attaching Light Kit
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan Light Kits (see store or catalog).
2. Downrod Extension Kits (see store or catalog).
3. Ceiling Fan Controls (see store or catalog).
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
WARNING
!
WARNING
!
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. Check the operation of the fan by gently pulling on
the 4-position speed control switch pull chain. The
operating sequence is as follows:
THREE-SPEED
1st Pull—HIGH 3rd Pull—Low
2nd Pull—Medium 4th Pull—OFF
3. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning, then
press the rocker switch located on top of the motor
housing, and turn the fan on again (Figure 16). The
fan blades will turn in the opposite direction and
reverse airflow.
4. Check the operation of the uplight by gently pulling
the light switch pull chain.
SPEED CONTROL
SWITCH PULL CHAIN
UPLIGHT SWITCH
PULL CHAIN
REVERSING SWITCH
TOP OF
MOTOR HOUSING
Figure 16
To install an Emerson accessory light kit, remove the
three screws securing the switch housing cover to the
switch housing. Remove the finial nut and cover pate
from the bottom of the switch housing cover and
install the light kit in accordance with the Emerson
light kit Owner’s Manual.
To avoid possible electrical shock, be sure electricity
is turned off at the main service box before wiring.
WARNING
!

Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers.
2. Loose power line connections to the fan, or 2. Check line power connections to fan and switch wire
loose switch wire connections in the switch connections in the switch housing.
housing. WARNING: Make sure main power is turned off.
2. Fan sounds 1. Blades not attached to fan. 1. Attach blades to fan before operating.
noisy. 2. Screws securing fan blade flanges to motor 2. Check to make sure the screws which attach the blade
are loose. flanges to the motor are tight.
3. Wire connectors inside switch housing rattling. 3. Check to make sure wire connectors in switch housing are
not rattling against each other or against the interior wall of
the switch housing.
WARNING: Make sure main power is turned off.
4. Screws holding blades to flanges are loose. 4. Tighten screws securely.
5. Loose screws in motor housing. 5. Check to make sure all screws in motor housing are snug
(not over-tight)
3. Fan wobbles 1. Setscrew in motor coupling is not tightened 1. Raise coupling cover and tighten setscrew securely.
excessively. securely.
2. Setscrew in the hanger ball/downrod assembly 2. Tighten the setscrew in the hanger ball/downrod assembly.
is loose.
3. Screws securing fan blade flanges to 3. Check to be sure screws which attach the fan blade flanges
motor are loose. to the motor are tight.
4. Fan blade flanges not seated properly. 4. Check to be sure the fan blade flanges seat firmly and
uniformly to the surface of the motor. If flanges are seated
incorrectly, loosen the flange screws and retighten
according to Step 12 and Figure 6.
5. Hanger bracket and/or ceiling outlet box is 5. Tighten the hanger bracket screws to the outlet box, and/or
not securely fastened secure outlet box.
6. Fan blades out of balance. 6. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
!
!
!
10

11
Repair Parts
28
29
6
10
9
30
31
12
23
11
32
1
8
4
5
7
21
7
6
24
25
FAN BLADE
(Order Separately)
13
14
15
33
32
26
20
27
18
19
17
19
16
22
Before discarding packaging material, be
certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS
GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• NAME OF ITEM
• PART DESCRIPTION
• MODEL NUMBER
The model number of your Fan will be found on
a label attached to the top housing.
For repair parts, phone [phone].

Part No. F40BP72780000 Printed in Taiwan 03/05 Form No. BP7278
Repair Parts Listing
Part Numbers
Key Model No. Model No. Model No. Model No. Model No. Model No.
No. Description CF2400AB00 CF2400BC00 CF2400ORB00 CF2400PW00 CF2400SCK00 CF2400WB00
* Hanger Pack, Consisting of: 761655-3 761655-24 761655-32 761655-22 761655-31 761655-20
1 Hanger Bracket — — — — — —
2 Hanger Ball — — — — — —
3 Downrod — — — — — —
* Parts Bag, Containing: 762548 762548 762548-1 762548-2 762548 762548
4 Wire Connector (4) — — — — — —
5 Setscrew Wrench, 5/32” — — — — — —
6 Knurled Knob (4) — — — — — —
7 Lockwasher (4) — — — — — —
8 Threaded Stud, 1-1/4” (2) — — — — — —
9 Threaded Stud, 1” (2) — — — — — —
10 Hairpin Pin — — — — — —
11 Clevis Pin — — — — — —
12 Setscrew, 5/16-18 x 1/4” — — — — — —
13 Screw, Phillips Pan Head,
#10-32 x 3/8” (16) — — — — — —
14 Washer, Flat, #10 (16) — — — — — —
15 Screw, Oval Head, #10-32 x 5/8” (11) — — — — — —
16 Screw, Pan Head, #8-32 x 3/8” (3) — — — — — —
17 Pendant, Fan Pull Chain — — — — — —
18 Pendant, Uplight Pull Switch — — — — — —
19 Coupling (2) — — — — — —
20 Cover, Ceiling 762556-5 762556-4 762556-12 762556-8 762556-11 762556-1
21 Cover, Motor 761621-3 761621-23 761621-25 761621-21 761621-24 761621-17
22 Capacitor, Aux. 10 uF 762242 762242 762242 762242 762242 762242
23 Motor 762508 762508 762508 762508 762508 762508
24 Hub, Motor 760601 760601 760601 760601 760601 760601
25 Flange Set, Blade (full set for one fan) 762540-5 762540-4 762540-12 762540-8 762540-11 762540-1
26 Housing Assembly, Switch 762542 762542 762542 762542 762542 762542
27 Cover, Switch Housing 762544-5 762544-4 762544-12 762544-8 762544-11 762544-1
28 Plate, Cover 762546-5 762546-4 762546-12 762546-8 762546-11 762546-1
29 Nut, Finial 762547-5 762547-4 762547-12 762547-8 762547-11 762547-1
30 Switch Assembly, Reversing 762627 762627 762627 762627 762627 762627
31 Harness Assembly, Uplight 762625 762625 762625 762625 762625 762625
32 T8 Candelabra Base Bulb, 25-watt (4) — — — — — —
33 Lead Assembly, Uplight (used only 761790 761790 761790 761790 761790 761790
for remote control operation)
—Owner's Manual BP7278 BP7278 BP7278 BP7278 BP7278 BP7278
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant ¥ St. Louis, MO 63136