Emerson CF960BS User manual

Part No. F40BP72680001 Form No. BP7268-1
READ AND SAVE THESE INSTRUCTIONS
WINDJAMMER™
®
Net Weight: 27.6 Lbs.
Ceiling Fan
Owner's Manual
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Company Do To Correct Problems:
Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or
blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan.
WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL,
REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR OTHER PROOF
OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division of Emerson
Company, 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center. You will be
responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort Ceiling Fan
should be properly packed to avoid damage in transit since we will not be responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any defects, malfunctions or failures
caused by:
• Repairs by persons not authorized by Emerson Company,
• Use of parts or accessories not authorized by Emerson Company,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and no employee,
agent, dealer or other person is authorized to give any warranties on behalf of Emerson Company.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT RESPONSIBLE
FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages
as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Model No.
CF960CK 00
CF960WB 00
CF960BS 00
®
Emerson
CeilingFans
-MODEL CF960 -

2
WARNING
!
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible
electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan provides the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. The light fixture supplied with the ceiling fan is designed to use a long neck 75-watt (maximum)
halogen flood lamp. Do not install a lamp that exceeds 75-watts.
7. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson. Substitution of parts or
accessories not designated for use with this product by Emerson could result in personal injury or
property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.

1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
a. Fan motor assembly
b. One light fixture assembly
c. Six fan blades
d. Six blade flanges
e. One ceiling cover
f. One hanger ball/downrod assembly
g. One hanger bracket
h. One coupling cover
i. One light fixture mounting plate
j. One PAR 30 75-watt halogen flood lamp
k. One light adapter plate
l. One loose parts bag containing:
1. Nineteen 3/16-24 x 5/16” slotted Phillips head
blade screws
2. Nineteen M5 flat washers
3. One large wood pendant
4. One small wood pendant
5. Two couplings
6. Thirteen 1/4-20 x 1/2” Phillips oval head
flange screws
7. Three wire connectors
8. Two threaded studs
9. Two #8 lockwashers
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver One stepladder
One 1/4” blade screwdriver One wire stripper
Three wire connectors (supplied).
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the following
size:
3
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
Before assembly your ceiling fan, refer to “Wiring Your
Ceiling Fan” section for proper method of wiring your
fan (page 6). If you feel you do not have enough wiring
knowledge or experience, have your fan installed by a
licensed electrician.
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
10. Two knurled knobs
11. One clevis pin
12. One hairpin clip
13. Four 5/32-32 x 5/16” Phillips flat head screws
14. Three 3/16-24 x 1/4” Phillips round head screws
15. One two-sided foam tape
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
LOOSE
PARTS
BAG
FAN MOTOR
ASSEMBLY
LIGHT FIXTURE
ASSEMBLY
BLADE
FLANGES
LIGHT FIXTURE
MOUNTING PLATE
COUPLING
COVER
CEILING
COVER HANGER
BRACKET HANGER BALL/
DOWNROD
ASSEMBLY
HALOGEN
FLOOD
LAMP
FAN
BLADES
LIGHT ADAPTER
PLATE
WARNING
!
WARNING
!
WARNING
!

5. Make sure the grommet is properly installed in the
coupling cover, then slide the coupling cover on
the downrod until it rests on the motor housing.
Place the ceiling cover over the downrod. Be sure
that the ceiling cover and the coupling cover are
both oriented correctly (Figure 4).
6. Reinstall the hanger ball (Figure 5) on the downrod
as follows. Route the three 80” motor leads through
the hanger ball. Position the pin through the two
holes in the downrod and align the hanger ball so the
pin is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball.
A loose setscrew could create fan wobble.
Assembling and Hanging
the Ceiling Fan
1. Remove the fan motor assembly from the protec-
tive plastic bag and then carefully remove the foam
shipping material from between the fan motor and
the upper housing (Figure 1).
2. Place the fan motor assembly in the lower styro-
foam pad with the top of the motor facing up. The
lower styrofoam pad serves as a holder for the fan
motor assembly during the first stages of assembly.
3. Remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 2). Remove the pin from the
downrod, then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 6.
4. Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Remove the upper setscrew from the
motor coupling. Align the clevis pin holes in the
downrod with the holes in the motor coupling.
Install the clevis pin and secure with the hairpin clip
(Figure 3). The clevis pin must go through the
holes in the motor coupling and the holes in the
downrod. Be sure to push the straight leg of the
hairpin clip through the hole near the end of the
clevis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must
be properly installed to prevent the clevis pin from
working loose. Pull on the downrod to make sure
the clevis pin is properly installed. Reinstall the
upper setscrew in the motor coupling (Figure 3).
Check that the two lower setscrews are tightened
securely.
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result. 4
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed could result in the fan falling.
WARNING
!
PIN
SETSCREW
HANGER
BALL
DOWNROD
Figure 2
MOTOR COUPLING
HAIRPIN
CLIP
UPPER
SETSCREW
CLEVIS
PIN
DOWNROD
CLEVIS
PIN
LOWER
SETSCREW (2)
HAIRPIN
CLIP
MOTOR
COUPLING
UPPER
SETSCREW
CLEVIS PIN
Figure 3
CEILING
COVER
GROMMET
COUPLING
COVER
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
Figure 4
REMOVE
FOAM SHIPPING MATERIAL
FAN MOTOR
HOUSING
FAN MOTOR
Figure 1

7.The fan comes with blue, black and white leads that
are 80” long. Before installing the fan, measure up
approximately 6 to 9-inches above the top of hanger
the ball/downrod assembly. Cut off excess leads
and strip back insulation 1/2-inch from the end of
leads.
8. Your new ceiling fan will require a grounded 120
volts AC, 60 Hz, 15 amp electrical supply line. If
your fan is to replace an existing ceiling light fix-
ture, turn electricity off at the main fuse box at this
time and remove the existing light fixture.
CEILING COVER
DOWNROD
PIN
SETSCREW
HANGER
BALL
Figure 5
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
WARNING
!
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 6).
CEILING
AT LEAST
7'
FLOOR
Figure 6
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician in in doubt.
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
WARNING
!
WARNING
!
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
Figure 7
10. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 8). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 7).
WARNING
!
WARNING
!
9.Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 7.)
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
Figure 8
5

3. Screw the two threaded studs (supplied) into the
tapped holes in the hanger bracket (Figure 9).
4. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 10).
5. Secure the ceiling cover in place by sliding #8
lockwashers over the threaded studs and installing the
two knurled knobs (supplied). (Figure 10). Tighten the
knurled knobs securely until the ceiling cover fits
snugly against the ceiling and the hole in the ceiling
cover is clear of the downrod.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the grounding conductor of supply (this
may be a bare wire or wire with green colored
insulation) (Figure 9). Securely connect the wires
using wire connector supplied.
2. Securely connect the fan motor white wire to the
supply white (neutral) wire using wire connector
supplied (Figure 9). Securely connect the fan motor
black wire and blue wire to the supply black (hot)
wire using wire connector supplied (Figure 9). After
connections have been made, turn leads upward
and carefully push leads into the outlet box, with
the white and green leads on one side of the outlet
box and the black and blue leads on the other side
of the outlet box.
6
Wiring Your Ceiling Fan
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is ground-
ed, contact a licensed electrician for advice, as it
must be grounded for safe operation.
NOTE: CEILING COVER
OMITTED FOR CLARITY.
GROUND
WIRE
LISTED
WIRE
CONNECTOR (3)
GREEN WIRE
(GROUND) FROM
HANGER BRACKET
GREEN WIRE
(GROUND) FROM
HANGER BALL
WHITE SUPPLY
(NEUTRAL)
WHITE FAN
WIRE
BLACK SUPPLY
(HOT)
BLACK AND BLUE
FAN WIRES
THREADED
STUD (2)
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire.
CEILING COVER
#8 LOCKWASHER
KNURLED KNOB
THREADED STUD
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
Final Assembly of the
Ceiling Fan
Figure 9
Figure 10
1. Mount the blade flange to the blade using three
3/16-24 x 5/16” slotted Phillips head screws and
three M5 flat washers (supplied) (Figure 11).
Repeat this procedure for the remaining five blades.
2. Install one blade assembly to the motor hub using
two 1/4-20 x 1/2” Phillips oval head screws
(Figure 12). Repeat this procedure for the
remaining five blade assemblies.
WARNING
!
WARNING
!
WARNING
!
M5 FLAT WASHER (3)
3/16-24 x 5/16" SLOTTED
PHILLIPS HEAD SCREW (3)
BLADE
BLADE FLANGE
Figure 11
1/4-20 x 1/2" PHILLIPS
OVAL HEAD SCREW
(2 PER BLADE FLANGE)
BLADE
ASSEMBLY
Figure 12

7
To avoid possible fire or shock, make sure that the
electrical wires are not pinched between the light
fixture assembly and the mounting plate.
WARNING
!
3. Partially install two 3/16-24 x 1/4” Phillips round
head screws in two of the tapped holes in the
coupling adapter (Figure 13). Leave two or three
threads untightened.
4. Position the keyhole slots in the light fixture mount-
ing plate over the two screws in the coupling
adapter (Figure 14). Rotate the mounting plate
clockwise to engage the slots under the screw
heads, then install a 3/16-24 x 1/4” Phillips round
head screw in the remaining tapped hole in the
coupling adapter. Tighten the two screws securing
the keyhole slots.
5. Engage the connector from the light fixture
assembly with the motor connector (Figure 15).
The two connectors are keyed and color-coded and
must be mated correctly (color-to-color) before they
can be engaged. Make sure the connector latch
closes properly.
COUPLING
ADAPTER
3/16-24 x 1/4" PHILLIPS
ROUND HEAD SCREWS (2)
Figure 13
LIGHT FIXTURE
MOUNTING PLATE
LIGHT FIXTURE
ASSEMBLY
MOTOR CONNECTOR
LIGHT FIXTURE
CONNECTOR
RECESSED
PORTION OF
MOUNTING
PLATE
PROVIDES
CLEARANCE
FOR LIGHT
FIXTURE
SWITCHES
Figure 15
LIGHT FIXTURE
MOUNTING PLATE
INSTALL 3/16-24 x 1/4" PHILLIPS
ROUND HEAD SCREW
TIGHTEN TWO 3/16-24 x 1/4"
PHILLIPS ROUND HEAD SCREWS
ROTATE MOUNTING
PLATE CLOCKWISE
2
3
1
Figure 14
6. Position the light fixture assembly over the light
fixture mounting plate. The light fixture switches
must be located in the recessed portion of the
mounting plate (Figure 15). Align the holes in the
light fixture with the holes in the mounting plate and
install four 5/32-32 x 5/16” Phillips flat head screws
(Figure 16). Carefully screw in the 75-watt halogen
flood lamp (supplied).
7. Cut the speed control switch and light control
switch pull chains to your desired length (optional).
Connect the wood pendant (supplied) to one pull
chain by sliding the wood pendant (small hole first)
onto the pull chain (Figure 16). Then attach a chain
coupling (supplied) to the end of the chain and
allow the pendant to slide down over the coupling.
Repeat this procedure for the other pull chain.
5/32-32 x 5/16" PHILLIPS
FLAT HEAD SCREW (4)
LIGHT FIXTURE
SWITCHES
LIGHT
FIXTURE
ASSEMBLY
WOOD PENDANT
CHAIN COUPLING
Figure 16
IMPORTANT
If you intend to install your ceiling fan without
using the light fixture supplied with the fan, or
if you are going to use a different Emerson light
fixture with your fan, proceed to “Installation of
Light Adapter Plate” Section on page 8.

8
Installation of
Light Adapter Plate
NOTE: In order to use the light adapter plate
(supplied), the wiring harness included as part of
the light fixture assembly must be removed and be
reinstalled in the light adapter plate. This Section
contains the procedures to accomplish this.
1. Disconnect the light fixture connector from the
wiring harness connector (Figure 17). Unscrew the
knurled nuts from the light switch and the speed
control switch. (The knurled nuts are not
interchangeable; keep them with their respective
switch.) Gently pry the capacitor (secured by
two-sided tape) from the light fixture assembly.
2. Remove and retain the two screws securing the
reversing switch to the light fixture (Figure 18).
Remove and retain the harness assembly.
3. Remove the knurled nut from one of the switch
chain bushings (Figure 18). Retain the knurled nut
and bushing for installation in the next step.
4. Position the switch chain bushing in the hole in the
light adapter plate (Figure 19) and secure using the
knurled nut.
5. Position the two switches of the harness assembly
in the mounting bracket; the small switch (light
switch) installs in the left hole and the larger switch
(speed control switch) installs in the right hole
(Figure 20). Secure the switches using the
appropriate knurled nuts. Pass the speed control
switch chain through the chain bushing. If desired,
tape the other switch chain to the adapter plate as
shown (tape not supplied).
6. Remove one protective covering from the two-
sided foam tape (supplied) and apply the foam tape
to the capacitor. Remove the remaining protective
covering and then firmly press the capacitor onto
the adapter plate (Figure 20).
7. Position the reversing switch in the slot in the
adapter plate and secure using two screws
(Figure 19).
8. Remove the screw plug (Figure 20) from the
bottom of the light adapter plate and install your
optional Emerson light fixture in accordance with
the light fixture Owner’s Manual.
IMPORTANT
Perform the procedures in this Section ONLY if
you intent to install your ceiling fan without
using the light fixture supplied with the fan, or
if you are going to use a different Emerson light
fixture with your fan.
IMPORTANT
The next three steps (step 8, 9 and 10) are to
be performed ONLY if you are installing an
optional Emerson light fixture. If you are
installing your fan without a light fixture,
proceed to step 11.
LIGHT FIXTURE
ASSEMBLY
CAPACITOR
SPEED CONTROL
SWITCH
KNURLED
NUT
KNURLED NUT
LIGHT SWITCH
DISCONNECT
THE LIGHT
FIXTURE
CONNECTOR
FROM THE
WIRING
HARNESS
CONNECTOR
WIRING
HARNESS
CONNECTOR
Figure 17
SCREW (2)
KNURLED NUT
SWITCH CHAIN
BUSHING
REVERSING
SWITCH
LIGHT FIXTURE
ASSEMBLY
Figure 18
SCREW (2)
KNURLED NUT
SWITCH CHAIN
BUSHING
REVERSING
SWITCH
LIGHT ADAPTER
PLATE
Figure 19
LIGHT ADAPTER
PLATE
CAPACITOR
SPEED CONTROL
SWITCH
KNURLED
NUT
KNURLED NUT
LIGHT SWITCH
SCREW
PLUG CHAIN
BUSHING
MOUNTING BRACKET
TAPE
Figure 20

9
Using Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. Check the operation of the fan by gently pulling on
the speed control pull chain switch (Figure 23). The
operating sequence is as follows:
THREE-SPEED
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
3. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning, then
slide the reversing switch to the opposite position,
and turn the fan on again. The fan blades will turn
in the opposite direction and reverse airflow.
4. Check the operation of the light fixture by gently
pulling on the light control pull chain switch.
SPEED CONTROL
SWITCH
LIGHT CONTROL
SWITCH
REVERSING
SWITCH
Figure 23
9. Carefully cut the blue wire going to the light switch.
Strip off 1/2-inch of insulation and connect this blue
wire to the blue wire from the light fixture (Figure
21) using a wire connector (supplied).
10.Carefully cut the white wire going to the
two-wire connector. Strip off 1/2-inch of insulation
and connect this white wire to the white wire from
the light fixture (Figure 21) using a wire connector
(supplied).
11.Engage the connector from the light adapter
plate with the connector from the motor
assembly (Figure 15). The two connectors are
keyed and color-coded and must be mated
correctly (color-to-color) before they can be
engaged. Make sure the connector latch closes
properly.
12.Position the light adapter plate over the light
fixture mounting plate. The adapter plate switches
must be located in the recessed portion of the
mounting plate (Figure 15). Align the holes in the
adapter plate with the holes in the mounting plate
and install four 5/32-32 x 5/16” Phillips flat head
screws (supplied) (Figure 22).
13.Cut the speed control switch pull chain to your
desired length (optional). Connect the wood
pendant (supplied) to the pull chain by sliding the
wood pendant (small hole first) onto the pull chain
(Figure 22). Then attach a chain coupling
(supplied) to the end of the chain and allow the
pendant to slide down over the coupling.
TWO-WIRE
CONNECTOR
4CONNECT TO WHITE
WIRE FROM LIGHT
FIXTURE
3CUT WHITE
WIRE HERE
2CONNECT TO BLUE WIRE
FROM LIGHT FIXTURE
CUT BLUE WIRE
HERE
LIGHT
SWITCH
1
Figure 21
To avoid possible fire or shock, make sure that the
electrical wires are not pinched between the light
adapter plate and the mounting plate.
WARNING
!
WOOD PENDANT
CHAIN COUPLING
ADAPTER PLATE
SWITCHES 5/32-32 x 5/16" PHILLIPS
FLAT HEAD SCREW (4)
LIGHT
ADAPTER
PLATE
Figure 22

10
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit
breakers.
2. Loose power line connections to the fan. 2. Check line wire connections to the fan.
WARNING: Make sure main power is
turned OFF.
3. Reversing switch in neutral position. 3. Make sure reversing switch position is all the
way to one side.
2. Fan sounds noisy. 1. Blades not attached to fan. 1. Attach blades to fan before operating.
2. Loose screws in motor housing. 2. Check to make sure all screws in motor
housing are snug (not over-tight).
3. Screws securing fan blade flanges to 3. Check to make sure the screws which attach
motor hub are loose. the fan flanges to the motor hub are tight.
4. Motor noise caused by solid-state 4. Some fan motors are sensitive to signals from
variable speed control. Solid-State variable speed controls. If Solid-
State Control is used and motor noise results
choose an alternative control method.
5. Screws holding blades to flanges 5. Tighten screws securely.
are loose.
3. Fan wobbles 1. Setscrew in motor coupling is loose. 1. Tighten setscrew securely in the motor
excessively. coupling.
2. Setscrew in hanger ball/downrod 2. Tighten the setscrew in the hanger ball/
assembly is loose. downrod assembly.
3. Screws securing fan blade flanges to 3. Check to be sure screws which attach the fan
motor are loose. blade flanges to the motor are tight.
4. Hanger bracket and/or ceiling outlet 4. Tighten the hanger bracket screws to the outlet
box is not securely fastened. box, and/or secure outlet box.
5. Fan blades out of balance. 5. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
!
!
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Maintenance
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
Accessories
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or
accessories not designated for use with this product
by Emerson Company could result in personal injury
or property damage.
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
1. Ceiling Fan/Light Controls (see store or catalog).
2. Downrod Extension Kits (see store or catalog).
3. Ceiling Fan Light Kits (see store or catalog).
WARNING
!
WARNING
!

13
26 27 14
28
16
17
15
24
20
9
19
18
3
1
5
4
6
7
8
2
21 25
23
22
12
11
10
11
Before discarding packaging material, be certain all
parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
• PART NUMBER • PART DESCRIPTION
• NAME OF ITEM • MODEL NUMBER
For repair parts, phone [phone].
Repair Parts

Part No. F40BP72680001 Printed in Taiwan 05/03 Form No. BP7268-1
Air Comfort Products
DIVISION OF EMERSON COMPANY
8100 W. Florissant ¥ St. Louis, MO 63136
Repair Parts Listing
Model No.
Key
No. Description CF960CK00 CF960WB00 CF960BS00
* Hanger Ball Assembly, 761655-23 761655-20 761655-17
Consisting of:
1 Hanger Bracket — — —
2 Hanger Ball — — —
3 Downrod — — —
* Parts Bag Containing: 762367 762367-1 762367-2
4 Wire Connector (3) — — —
5 Threaded Stud (2) — — —
6 Lockwasher, #8 (2) — — —
7 Knurled Knob (2) — — —
8 Clip, Hairpin — — —
9 Pin, Clevis — — —
10 Screw, 3/16-24 x 5/16” (19) — — —
11 Flat Washer, M5 (19) — — —
12 Screw, 1/4-20 x 1/2” (13) — — —
13 Screw, 3/16-24 x 1/4” (3) — — —
14 Screw, 5/32-32 x 5/16” (4) — — —
15 Pendant, Wood, Small — — —
16 Pendant, Wood, Large — — —
17 Coupling, Chain (2) — — —
18 Cover, Ceiling 670169-34 670169-30 670169-15
19 Cover, Coupling 761860-18 761860-6 761860-3
20 Housing, Upper 762334 762334-1 762334-2
21 Adapter, Coupling 762331 762331 762331
22 Blade (Set of 6) 762329 762329-1 762329-2
23 Flange (Set of 6) 762333 762333-1 762333-2
24 Plate, Mounting 762327 762327 762327
25 Adapter Plate, Light 762384 762384-1 762384-2
26 Harness, Wiring 762337-2 762337-1 762337
27 Light Fixture Assembly 762366 762366-1 762366-2
28 Flood Lamp, 75W, Long Neck,
Halogen, PAR 30 — — —
—Owner's Manual BP7268-1 BP7268-1 BP7268-1