Emerson Provence CF2300TG01 User manual

READ AND SAVE THESE INSTRUCTIONS
“Provence” Series
Model No.
CF2300TG01
CF2300S01
CF2300OB01
CF2300WB01
Provence Series
Ceiling Fan Owner's Manual
Part No. F40BP72170001 Form No. BP7217-1
®
Net Weight: 23.8 Lbs.

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local
Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in
doubt.
4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not
know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Company could result in person-
al injury or property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
2
WARNING
!

1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following:
a. Fan motor and housing assembly
b. One motor cover
c. One ceiling cover
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket
g. One switch housing cover
h. One uplight lead assembly
i. One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. Eleven 10-32 x 5/8" oval head screws
4. Two 1” threaded studs
5. Two 1-1/4” threaded studs
6. Four knurled knobs
7. Three wire connectors
8. Two screws 8-32 x 3/8"
9. Two pull chain pendants, and couplings
10. One hairpin clip
11. One clevis pin
12. Two lockwashers
13. Sixteen 10-32 x 3/8" pan head screws
14. Sixteen flat washers
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver One stepladder
Three wire connectors (supplied.) One wire stripper
MATERIALS
Wiring, outlet box and box connectors must be of type
required by the local code. The minimum wire would be a
3-conductor (2-wire with ground) of size shown at right:
3
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is com-
pleted, place a check mark in the box. This will insure that all steps have been completed
and will be helpful in finding your place should you be interrupted.
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local retail-
er or catalog outlet for replacement before pro-
ceeding.
NOTE: Fan blades are ordered separately and are
packaged in separate carton.
FOAM
PACKING
PROTECTIVE
PLASTIC BAG
FOAM
PACKING
CARTON
MOTOR AND
HOUSING ASSEMBLY
HANGER BALL/
DOWNROD
ASSEMBLY
HANGER
BRACKET
LOOSE
PARTS BAG
BLADE
FLANGES
SWITCH
HOUSING
COVER
CEILING
COVER
MOTOR
COVER
UPLIGHT
LEAD
ASSEMBLY
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces-
sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.
WARNING
!
WARNING
!

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and capa-
ble of withstanding a load of at least 50 pounds.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
4
SECTION A
Assembly Instructions
for Installing the CF2300
Ceiling Fan with a SR120
Remote Control or with a
SW140 Wall Control
1. Cut the white, blue, and black wires about 3"
above the motor coupling (Figure 1). Strip insula-
tion 1/2" from end of wires and install a wire
connector on the black wire; this wire will not be
used. Remove the wire connectors from the red
and brown wires.
2. Loosen the setscrew in the hanger ball, slide the ball
down the downrod, and remove the clevis pin. Then
slide the hanger ball off the downrod (Figure 2).
Retain all parts for reinstallation in step 11.
3. Push the wiring harness connector and the con-
nector on the blue wire (both supplied with the
SR120 Remote Control and the SW140 Wall
Control), and the connector on the uplight yellow
lead assembly (supplied with the fan) through the
downrod until they all extend about 4” out of the
downrod (Figure 3).
4. Cut all wires approximately 3" from the end of the
downrod’. Strip insulation 1/2" from end of wires.
3"
WHITE WIRE BLACK WIRE
BLUE WIRE
REMOVE WIRE
CONNECTORS
FROM RED AND
BROWN WIRES
INSULATE BLACK
WIRE USING WIRE
CONNECTOR
YELLOW
WIRE
MOTOR
COUPLING MOTOR COUPLING SLOT
Figure 1
HANGER BALL
DOWNROD
CLEVIS PIN
SETSCREW
Figure 2
4"
DOWNROD
CUT HERE
3"
UPLIGHT YELLOW LEAD ASSEMBLY
WIRING
HARNESS
BLUE WIRE
Figure 3
Electrical Requirements
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
The Emerson CF2300 Ceiling Fan is designed to be
operated from a SR120 Remote Control, from a
SW140 Wall Control, or from other fan/light controls.
There are no controls supplied with the ceiling fan. If
you are going to control your ceiling fan with a SR120
Remote Control or with a SW140 Wall Control, proceed
to “SECTION A”. If you are going to control your ceiling
fan in any other manner, proceed to “SECTION B”.
Uplight
This fan is supplied with a built-in uplight in the motor
housing. This uplight does not have a built-in switch to
turn it ON or OFF. A separate switch control must be
used to operate the uplight. This can be done with a
separate ON/OFF wall switch or one of the many
Emerson Fan/Light Controls, such as the SR120,
SW140 or SW95L controls. The yellow lead supplied
with this fan is the power lead for the uplight.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.
WARNING
!If the CF2300 ceiling fan is being installed with any
other control method, skip
SECTION A and go to
SECTION B to begin assembly instructions.
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
!
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these instruc-
tions should be done or approved by a licensed elec-
trician.
WARNING
!

NOTE: Make sure the unused black motor lead is
capped with a wire connector. Make sure all wire
connectors are completely inside motor coupling
cover and not pinched between the motor
coupling cover and motor.
9. Screw two 1” threaded studs (supplied) into the
motor (Figure 6). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until
the threaded studs protrude; install two knurled
knobs (supplied) to secure the cover.
10. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 7).
7/8"
KNURLED KNOB
1" THREADED
STUD
MOTOR
MOTOR
COUPLING
COVER
WIRE
CONNECTORS
Figure 6
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
DOWNROD
LEADS TO BE
POSITIONED IN
SLOT IN MOTOR
COUPLING
CLEVIS
PIN
Figure 5
5
5. Using wiring connectors (supplied), connect the
white, red, blue, brown, and yellow wires from the
downrod to the white, red, blue, brown and yellow
wires of the ceiling fan (Figure 4). Wires must be
connected color-to-color.
6. Fold all wires from the downrod into the slot in the
motor coupling, slide the downrod down the wires
and seat the downrod in the motor coupling. All
wires and wire connectors should be placed
through the motor coupling slot beneath the down-
rod (See Figure 5).
7. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod (Figure 5). Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose.
8. Install the setscrew (supplied in the loose parts
bag) in the motor coupling and tighten using the
5/32” setscrew wrench (supplied) (Figure 5).
FAN BLADES REMOVED
FOR CLARITY
DOWNROD
BLACK WIRE
WHITE WIRE
WIRING HARNESS
CONNECTOR
YELLOW WIRE
TO YELLOW
WIRE
BLUE WIRE
TO
BLUE WIRE
RECEIVER
BROWN WIRE
TO BROWN WIRE
YELLOW WIRE
TO YELLOW WIRE
LISTED GENERAL
USE ON/OFF
WALL SWITCH
(MUST BE
USED WITH SR120
REMOTE CONTROL)
RECEIVER
CONNECTOR
RED WIRE
TO RED WIRE
WHITE WIRE
TO WHITE WIRE
BLACK WIRE
(NOT USED)
BLUE WIRE
TO BLUE WIRE
BLACK WIRE
WHITE WIRE
BLACK
WIRE WHITE
WIRE
BLACK
WHITE
BLACK
SW140
WALL
CONTROL
FAN
HOUSING
TO
120V SUPPLY
TO
120V SUPPLY
LIGHT FIXTURE
Figure 4
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tight-
ened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!

15. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box (Figure 11).
6
11. Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 7). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is cap-
tured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball. A
loose setscrew could create fan wobble.
12.Use three 10-32 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade
(Figure 8). Repeat for the remaining four blades.
13.Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade assemblies
(blades ordered separately) in accordance with
Step 14.
14.Attach one blade assembly to the motor hub using
two 10-32 x 5/8" oval head screws (supplied)
(Figure 9). Do not tighten completely at this time.
Install remaining blade assemblies in the same
way. Gently snug all flange screws to the motor
hub, working around the hub in a clockwise
sequence. Next, securely tighten all flange screws,
again working in a clockwise sequence. Failure to
follow this procedure could result in fan wobble.
This completes the blade installation.
SETSCREW
DOWNROD
PIN
HANGER BALL
CEILING COVER
Figure 7
MOTOR
HUB
10-32 x 5/8"
OVAL HEAD SCREWS
(2 PER BLADE
ASSEMBLY)
10-32 x 3/8" PAN HEAD
SCREW (3)
FLAT WASHER (3)
BLADE
BLADE
FLANGE
Figure 8
Figure 9
CEILING
FLOOR
AT LEAST
7'
Figure 10
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
To reduce the risk of personal injury, do not bend the
blade flanges when installing the blades or cleaning
the fan. Do not insert foreign objects between rotat-
ing fan blades.
WARNING
!
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 10).
WARNING
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician in in doubt.
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!

7
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
Figure 11
Figure 12
16. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket
that was just attached to the outlet box (Figure
12). Be sure the groove in the ball is lined up with
tab on the hanger bracket (Figure 11).
19. Securely connect the wiring harness connector to
the receiver connector, and connect the blue and
yellow wires to the blue and yellow wires from the
receiver (Figure 4).
20. Turn the receiver so that the flat side aligns with
the open side of the hanger bracket (Figure 13).
Fold and position the wires into the space above
the hanger ball and into the outlet box.
21. Feed the wires and connectors around the out-
side of the receiver, through the open side of the
hanger bracket, and into the outlet box. Slide the
receiver up and over the hanger bracket.
Remove the backing on the foam adhesive pads
and press the receiver against the ceiling.
22. To complete the ceiling fan assembly, skip to the
“FINAL ASSEMBLY” section of this Owner’s
Manual.
17. Position the receiver (supplied with the SR120
Remote Control or SW140 Wall Control) by pass-
ing the opening in the receiver over the downrod
(Figure 13).
18. Connect the black wire from the wiring harness to
the black (hot) supply wire (Figure 4). Connect the
white wire from the wiring harness to the white
(neutral) supply wiring. Connect the green ground
wires from the hanger bracket and the hanger ball
to the supply ground wire. Use wire connectors
supplied with your ceiling fan.
HANGER
BRACKET HANGER
BALL
CEILING
COVER
SW375
RECEIVER
FLAT SIDE
OPEN
SIDE
Figure 13
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
To avoid possible fire or shock, be sure that
electricity is turned off at the main fuse box before
wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
WARNING
!
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!

9. Install the setscrew (supplied in loose parts bag) in
the motor coupling and tighten using the 5/32"
setscrew wrench (supplied) (Figure 17).
10.Screw two 1” threaded studs (provided) into the
motor (Figure 22). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until
the threaded studs protrude; install two knurled
knobs (supplied) to secure the cover.
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
DOWNROD
CONNECT YELLOW LEAD
TO YELLOW LEAD
CLEVIS
PIN
Figure 16
DOWNROD
SETSCREW
Figure 17
8
SECTION B
Assembly Instructions
for Installing the CF2300
Ceiling Fan with Any Other
Control Method
(excluding the SR120 Remote
Control or the SW140 Wall Control)
1. Position the fan motor and housing assembly in the
lower foam packing so that the top of the motor is fac-
ing you.
2. Separate, untwist and unkink the four motor leads.
3. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 14). Remove the pin from the
downrod , then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in step 9.
4. Push the uplight yellow lead assembly connector
through the downrod (Figure 15) until it extends
about 4”.
5. Cut the yellow lead approximately 3” from the end
of the pipe. Strip insulation 1/2” from end of the
wires.
6. Using the wire connector supplied, connect the
uplight yellow lead assembly to the yellow lead
from the fan motor and housing assembly (Figure
16).
7. Route the white, blue, and black motor leads through
the downrod. Fold the yellow, red, and brown wires
into the slot in the motor coupling, slide the downrod
down the wires and seat the downrod in the motor
coupling (Figure 16).
8. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin and
secure with the hairpin clip (Figure 16). The clevis pin
must go through the holes in the motor coupling and
the holes in the downrod . Push the straight leg of the
hairpin clip through the hole near the end of the cle-
vis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from work-
ing loose. Pull on the hanger ball to make sure the
clevis pin is properly installed.
HANGER BALL
DOWNROD
CLEVIS PIN
SETSCREW
Figure 14
4"
DOWNROD
CUT
HERE
3"
UPLIGHT YELLOW
LEAD ASSEMBLY
Figure 15
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tight-
ened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!

14.Use three 10-32 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade
(Figure 20). Repeat for the remaining four blades.
15.Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade assemblies
(ordered separately) in accordance with Step 16.
16.Attach one blade assembly to the motor hub using
two 10-32 x 5/8" oval head screws (supplied)
(Figure 21). Do not tighten completely at this time.
Install remaining blade assemblies in the same
way. Gently snug all flange screws to the motor
hub, working around the hub in a clockwise
sequence. Next, securely tighten all flange screws,
again working in a clockwise sequence. Failure to
follow this procedure could result in fan wobble.
This completes the blade installation.
9
NOTE: Make sure the red and brown leads are
capped with wire connectors. Make sure red,
brown, and yellow wire connectors are completely
inside motor coupling cover and not pinched
between the motor coupling cover and motor.
11.Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 19).
12.Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 19). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is
captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin
and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
13.The blue, black, yellow and white leads exiting the
downrod are 80-inches long. Before installing fan,
measure up approximately 6 to 9-inches above the
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
NOTE: If you are installing your fan with a SR120
Remote Control or SW 120 Wall Control, Do Not
Cut Terminal Off of the Yellow Lead.
(See Section A.)
7/8"
RED LEAD
WIRE
CONNECTORS
KNURLED KNOB
1" THREADED
STUD
MOTOR
MOTOR
COUPLING
COVER
WIRE CONNECTOR
YELLOW LEADS
BROWN LEAD
Figure 18
SETSCREW
DOWNROD
PIN
HANGER BALL
CEILING COVER
Figure 19
MOTOR
HUB
10-32 x 5/8"
OVAL HEAD SCREWS
(2 PER BLADE
ASSEMBLY)
10-32 x 3/8" PAN HEAD
SCREW (3)
FLAT WASHER (3)
BLADE
BLADE
FLANGE
Figure 20
Figure 21
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
To reduce the risk of personal injury, do not bend the
blade flanges when installing the blades or cleaning
the fan. Do not insert foreign objects between rotat-
ing fan blades.
WARNING
!

17. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box (Figure 23).
18. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 24). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 23).
NOTE: If you are installing a SR120 Remote
Control or a SW140 Wall Control to operate the
fan and light, refer to the installation instructions
and wiring diagrams shown in Section A of this
Owner’s Manual.
19. For a wall control installation you will need a
three-wire (with ground) conductor cable between
the ceiling and wall outlet boxes. This will allow
you to control the fan separately from the lights.
Figure 25 is a basic wiring diagram that will con-
trol the uplight and downlight on a switch and the
fan on a separate control. Refer to the installation
instructions and wiring diagrams supplied with the
Emerson Fan Control Owner’s Manual.
a. Connect the green grounding lead from the
hanger ball and the green grounding lead from
the hanger bracket to the grounding conductor
of supply (this may be a bare wire or a wire
with green colored insulation). Securely con-
nect wires with wire connector supplied.
b. Securely connect the white wire from the
downrod to the supply white (neutral) wire
using wire connector supplied. Securely con-
nect the black wire from the downrod to the
supply black (hot) wire using wire connector
supplied.
c. Cut terminal off of the yellow lead wire and
strip insulation 1/2” from end of wire.
d. Securely connect the blue wire and yellow wire
from the downrod to the supply red (hot) wire
using wire connector (supplied). After connec-
tions have been made, turn leads upward and
carefully push leads into the outlet box, with
the white and green leads on one side of the
outlet box and the black, blue and yellow leads
on the other side of the outlet box.
20. To complete the ceiling fan assembly, proceed to
the “FINAL ASSEMBLY” section.
10
CEILING
FLOOR
AT LEAST
7'
Figure 22
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
Figure 23
Figure 24
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 22).
WARNING
!
The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs.
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician in in doubt.
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
To avoid possible fire or shock, be sure that
electricity is turned off at the main fuse box before
wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
WARNING
!