Emerson dixell User manual

PROG TOOL

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 2/8
1. BEFORE USE
Caution: avoid any contact of this equipment with rain or water, in order to
prevent the development of flames or electric shock.
Caution: do not remove the cover, in order to
reduce the risk of electric shock. There are no
components inside that need maintenance by
the user. Always refer to qualified service
staff for any intervention.
The symbol characterized by a lightning inside an equilateral triangle is
intended to alert the user of a non-insultated voltage souce within the
product area that is sufficiently high to constitute a risk of electric shock to
persons.
The symbol characterized by an esclamation mark inside an equilateral
triangle is intended to alert the user of important operating and maintenance
(servicing) instructions.
CAUTION
This equipment must be installed only by the service staff with adequate
technical training and experience, in order to be aware of any possible
danger. Operations described in this manual are intended to be for exclusive
use of the service staff. The user is is not enabled to open the device.
CAUTION
Dixell Srl reserves the right to modify this user’s manual at any time without
prior notice. The latest version available can be dowloaded from the website.
CAUTION
This is a class A product. In residential environments it can cause radio
interference. In this case the user may need to take appropriate measures.
CAUTION
Dixell Srl reserves the right to change the components of its products, even
without notice, ensuring the same and unchanged functionality.
CAUTION
Since Dixell products are part of a high-level technology, a qualification and
a configuration/programming/commissioning stage is required to best use
them. Otherwise, these products may malfunction and Dixell cannot be held
responsible. The product must not be used in any way that differs from that
stipulated in the documentation.

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 3/8
2. PRODUCT DISPOSAL (WEEE)
In compliance with the DIRECTIVE 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF
THE COUNCIL of July 4th 2012 regarding Waste Electrical and Electronic Equipment (WEEE)
and to the relative national legislation, we inform all EEE housholds users that:
➢There lies the obligation not to dispose of electrical and electronic waste as municipal
waste but to separate the waste;
➢Public or private collection points must be used to dispose of the goods in accordance with
local laws. Furthermore, at the end of the product’s life, it is also possible to return this to
the retailer when a new purchase is made.
➢This equipment may contains hazardous substances. Improper use or incorrect disposal
can have adverse effects on human health and the environment.
➢The symbol shown on the product or the package indicates that the product be
disposed of as separated waste.
➢Should the product be disposed of incorrectly, sanctions may be applied as stipulated in
applicable local regulations regarding waste disposal.
3. PACKAGE
The KIT PROG-TOOL package contains the following objects:
A. 1 PROG TOOL unity
B. 1 CAB/PTK2 cable of 2m lenght
C. 1 CAB/PTK485 cable of 2m lenght
to connect it to the RS485 port
D. 1 RS232/USB serial adaptor to
connect it to the PC*
E. 1 PROG TOOL charging cable
* The package contains a CD with the drivers for RS232/USB serial converter; before installing
the drivers, verify if the PC automatically recognizes the converter.

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 4/8
4. PROG-TOOL USE
The PROG TOOL unit can be used to create HOT KEY programming keys and/or to interface
DIXELL controllers to a PC in order to modify the parameters map using the Wizmate software.
4.1 WIRING DIAGRAM
4.2 LEDS MEANING
PROG TOOL is equipped with 3 colored LEDS to signal the different functioning states
Programmed HOT KEY to be copied
Interface Led
HOT KEY output port to
program new hot keys
Button to load parameters map
in the new Hot Key
Instruments without Rs485:
TTL output for power supply
and programming
INSTRUMENTS with RS485 on board:
TTL connector for power supply and
Rs485 port.
Green Led = power supply On
Yellow Led = Hot Key programming
Blinking yellow Led = communication between PC and PROG TOOL
Red Led = Hot Key programming error
Green Led = Hot Key successfully programmed
Interface Leds

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 5/8
4.3 PROGRAMMING FROM HOT-KEY TO HOT-KEY
This function allows to copy any HOT KEY that is already programmed.
Connect the power supply to the terminal blocks 13 and 14 and make sure the “Power”
Led is turned on.
1. Insert the original key in the connector on the top side of the programmer.
2. Insert the key to be programmed in the “Hot-Key Copy” connector placed on the PROG
TOOL front
3. Press the “Copy” button to start the key copying procedure. During the operation the “Copy”
Led is blinking green
4. After a few seconds the “Copy” Led stops blinking and provides the result of the operation
RED “Copy” Led = error during the HOT KEY programming, repeat the operation and
eventually replace the key.
GREEN “Copy” Led = successfully performed operation; Hot Key has been correctly
programmed.
5. Remove the new key. It is possible to create further copies by inserting a new Hot Key to be
programmed.
Programmed Hot Key to be
copied
Interface Led
Press to start copying
Insert the key to be
programmed
Power Supply

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 6/8
4.4 PROGRAMMING FROM PC TO HOT-KEY
Using the PROG TOOL unit connected to a PC and the Wizmate software (included in the
CD-Rom) it is possible to create Hot Keys, according to your needs.
6. Create the parameters map with the desired values using Wizmate software and copy it in
PROG TOOL (see paragraph “HOT KEY CREATION”).
7. Connect the PROG TOOL to the PC using the RS232/USB serial converter.
8. Insert the Hot Key to be programmed in the “Hot Key Copy” connector placed on the unit
front.
9. Press the “Copy” button placed on the PROG TOOL front; the “Copy” Led starts blinking.
10. After a few seconds the “Copy” Led stops blinking and provides the result of the operation.
RED “Copy” Led = error during the HOT KEY programming, repeat the operation and
eventually replace the key.
GREEN “Copy” Led = successfully performed operation; Hot Key has been correctly
programmed.
11. Remove the programmed Hot Key.
Note: it is now possible to create further copies of the Hot Key simply repeating the steps from 2
to 5
Interface Led
Press to copy the
parameters into the
Hot Key
Insert the key to be
programmed
110Vac or 230Vac
Power Supply

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 7/8
4.5 PROGRAMMING FROM PC TO INSTRUMENT
The use of PROG TOOL along with Wizmate software allows to verify and/or modify the
parameters map of an instrument.
The instrument to be programmed must be connected to the PROG TOOL following one of the
schemes indicated in the following pages (connection mode depends on the fact that the
instrument has the RS485 serial port or not) and its compatibility (instrument model and software
version) with Wizmate software must be verified using the table of Chapter 5 of this manual.
NOTE: parameters reading and/or writing is possible only for those controllers equipped with
RS485 or TTL serial communication port.
For all instruments not equipped with serial port (PRIME and WING BASIC series) it is only
possible to create HOY KEYS with which is then possible to program devices.
CONNECTION OF AN INSTRUMENT EQUIPPED WITH RS485
SERIAL PORT
1. Connect the RS485 port of the instrument to the RS495 terminals of the PROG TOOL (16
and 17) through a double wired cable, respecting the + and - polarity.
2. Connect the “+5V Supply” connector placed on the PROG TOOL side to the TTL (Hot Key)
port of the instrument by using the CAB/RS2 cable. This operation provides power supply to
the instrument with no need for further connections.
3. Connect the PROG TOOL to the PC by using the serial converter RS232/USB.
4. It is now possible to check and eventually modify the programming of the instrument through
the Wizmate software.
Interface Led
Instrument power supply
(CAB/RS2)
110Vac or 230Vac
Power Supply
2 wired cable
for Rs485

1592010400 PROG TOOL EN 19.03.2020 PROG TOOL 8/8
CONNECTION OF AN INSTRUMENT NOT EQUIPPED WITH RS485
SERIAL PORT
1. Connect the “TTL” connector placed on the side of PROG TOOL to the TTL port (Hot Key)
of the instrument by using the CAB/RS2 cable. This operation provides both power supply
and serial communication with no need for further connections.
2. Connect the PROG TOOL to the PC by using the serial converter RS232/USB.
3. It is now possible to check and eventually modify the programming of the instrument through
the Wizmate software.
5. TECHNICAL DATA
Power supply: 115V +/- 10%, 50/60 Hz, 230V +/- 10%, 50/60 Hz
Power absorption: 3VA max
Operating temperature: 060 °C
Relative humidity: 2085 % (non-condensing)
Storage temperature: -4085 °C
6. OPERATION
For operational procedures refer to WIZMATE MANUAL in the “Manuals Download” section of
the website http://www.dixell.com, where you can find the latest updated version.
110Vac or 230Vac
Power Supply
Interface Led
Serial communication
and instrument power
supply (CAB/RS2)