Emerson Rosemount 2120 Configuration guide

Manual Supplement
00809-0200-4030, Rev BA
November 2012
Replacement and Calibration of
Rosemount 2120 Electronic Cassettes

November 2012
2
Manual Supplement
NOTICE
Refer to the Rosemount 2120 Reference Manual (Document Number 00809-0100-4030) for
more instructions. Manuals are available electronically on www.rosemount.com.
Failure to follow these installation guidelines could result in death or serious injury
The Rosemount 2120 is a liquid level switch. It must be installed, connected, commissioned,
operated, and maintained by suitably qualified personnel only, observing any national and
local requirements that may apply
Ensure the wiring is suitable for the electrical current and the insulation is suitable for the
voltage, temperature, and environment
Use the equipment only as specified. Failure to do so may impair the protection provided by
the equipment
Any substitution of non-recognized parts may jeopardize safety and is under no
circumstances allowed
Explosions could result in death or serious injury
Installation of the 2120 in a hazardous environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please review
the Product Certifications section for any restrictions associated with a safe installation
Verify that the operating atmosphere of the 2120 is consistent with the appropriate
hazardous locations certifications
External surface may be hot
Care must be taken to avoid possible burns
Process leaks could result in death or serious injury
Install and tighten process connectors before applying pressure
Do not attempt to loosen or remove process connectors while the 2120 is in service
Electrical shock could cause death or serious injury
If the liquid level switch is installed in a high voltage environment and a fault condition or
installation error occurs, high voltage may be present on leads and terminals
Use extreme caution when making contact with the leads and terminals
Make sure that power to the 2120 is off while making connections

Manual Supplement
3
November 2012
Replacement and calibration of electronic cassettes
When replacing a damaged or faulty cassette, it is necessary to calibrate the
replacement cassette to the operating frequency of the fork assembly.
Replacement sequence
If this replacement is taking place in a hazardous area, only qualified personnel should
perform the replacement. All work in hazardous areas must be carried out in
accordance to national and local codes of practice. Refer to the Rosemount 2120
manual (00809-0100-4030) for product certifications and safety instructions for
specific hazardous area installations.
Calibration of this device is complex and it may take several attempts before
calibration is successful.
On Intrinsically Safe (I.S.) approved versions of the 2120, it is recommended that
replacement and calibration be performed in a non-hazardous (safe) area.
Note
In I.S. applications, NAMUR cassettes can only be replaced with NAMUR cassettes,
and 8/16 mA cassettes can only be replaced by 8/16 mA cassettes
Non-I.S. cassettes can be interchanged with other non-I.S. cassettes, but the new
label must be fitted and the original part number transferred to the new label
(see “Electrical installation” on page 7 for connections to the electronic cassettes)
Before starting the replacement and calibration procedure, ensure that any controlled
process will not be adversely affected
To replace the cassette, do the following:
1. Isolate and disconnect the power to the Rosemount 2120, and insulate the ends of
the wires. On a 2120 with a relay cassette, there may be more than one power
source.
2. Remove the cover and disconnect the wires, noting any connections (Figure 1) and
the exact mode switch position (Figure 2) on the cassette to be replaced.
3. Remove and retain the two fixing screws from the base of the cassette and unplug
the cassette.
4. Plug in the replacement cassette, refit the screws, reconnect the wires, and set the
mode switch to “Wet On” with a one second delay (Figure 3).
5. Reconnect the power to the 2120.
6. Proceed to “Calibration sequence” on page 5.
Figure 1. Top-down view of example cassette inside the housing
A. LED
B. Mode Switch and Time Delay
OPERATION MODE
Dry On Mode
Dry
Wet
Wet On Mode
Dry
Wet
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
123
OUT
+-
4
PLC/PNP
Isolate Supply
Before Removing
B
A

November 2012
4
Manual Supplement
Figure 2. Mode switch and setting on the existing cassette
This is an example of how the existing cassette may look.
Here, the switch is set to “Dry On” with a one second delay.
Take note of the actual setting.
SETTING IS: ___________________________
Figure 3. Mode switch setting on the replacement cassette
Set the mode switch of the new cassette to “Wet On” with a
one second delay.
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1

Manual Supplement
5
November 2012
Calibration sequence
This section describes what is required for calibration. Calibration sequence steps 3 to
13 are time dependent and must be carried out within the noted times. The purpose of
the time dependency and switching sequence is to prevent an accidental calibration
from occurring.
To calibrate the cassette, do the following:
1. Ensure that the forks are dry, and the mode switch is set to “Wet On” with a one
second time delay (Figure 3).
2. Check that the LED is flashing at a rate of one flash per second.
If it is on continuously, proceed to step 8.
3. Apply magnet to the test-point (as shown on page 6).
4. After a one second delay, the LED will be lit continuously.
5. Within one second, rotate the mode switch two steps clockwise.
6. After a two second delay, the LED will go out.
7. Within three seconds, rotate the mode switch two steps counter-clockwise.
Proceed to step 13.
8. Apply magnet to test point (as shown on page 6).
9. After a one second delay, the LED will flash at a rate of one flash per second.
10. Within one second, rotate the mode switch two steps clockwise.
11. After a two second delay, the LED will go out (stop flashing).
12. Within three seconds, rotate the mode switch two steps counter-clockwise.
13. After a two second delay, the LED should flash twice per second.
14. If the LED is flashing twice per second, the calibration has occurred correctly.
Remove the magnet from the test-point. After a one second delay, the unit will
return to normal operation. Proceed to step 17.
15. If the LED is flashing once per second or it is on continuously, the calibration has
failed. Remove the magnet from the test-point, wait ten seconds, and then repeat
from step 2.
16. If the LED stays off after the two second delay of step 13, the sensor is not working
correctly. Check that the sensor forks are clean and dry. Also, verify there is nothing
jamming or touching the sensor. If no fault is found with the sensor, the entire unit
should be returned for repair.
17. Set the mode switch to the original setting noted in Figure 2 and wait five seconds.
18. Replace the cover and check that the system works.

November 2012
6
Manual Supplement
Figure 4. Magnetic test point (metal housing)
Figure 5. Magnetic test point (glass-filled nylon housing)
TP TP TP
S
N
S
N
(OUTPUT ON)
(OUTPUT ON)
(OUTPUT OFF)
(OUTPUT OFF)
NO MAGNET MAGNET
~
20 - 264Vac
50 - 60Hz 2VA
20 - 60Vdc 0.5W
Output Rating:
Load 20 - 500mA
Supply
www.rosemount.com
MAX PROCESS TEMPERATURE:150°C
MADE IN UNITED KINGDOM
MAX WORKING PRESSUREAT 20°C: 0.25 bar
DIRECT LOAD SWITCHING
MAGNETIC
TEST
POINT
41001029
*41001029*
2120D0AS1NAAA
~
20 - 264Vac
50 - 60Hz 2VA
20 - 60Vdc 0.5W
Output Rating:
Load 20 - 500mA
Supply
www.rosemount.com
MAX PROCESS TEMPERATURE:150°C
MADE IN UNITED KINGDOM
MAX WORKING PRESSUREAT 20°C: 0.25 bar
DIRECT LOAD SWITCHING
MAGNETIC
TEST
POINT
41001029
*41001029*
2120D0AS1NAAA
MAGNETIC
TEST
POINT
S
N
S
N
(OUTPUT ON)
(OUTPUT ON)
(OUTPUT OFF)
(OUTPUT OFF)
NO MAGNET MAGNET

Manual Supplement
7
November 2012
Electrical installation
Before use, check that suitable cable glands and blanking plugs are fitted and
fully tightened.
Isolate supply before connecting the switch or removing the electronics.
The Protective Earth (PE) terminal must be connected to an external
earthing system.
Direct load switching electronics cassette (two-wire, red label)
High level Dry = ON Low level Wet = ON
LED on continuously LED flashes each
second LED on continuously LED flashes each
second
Direct Load
Switching
WARNING
Isolate Supply
Before Removing
OPERATION MODE
Dry On Mode
Dry
Wet
Wet On Mode
Dry
Wet
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
123
LINE
LOAD
PE
(Ground)
Neutral Live
0V
Fuse 2A(T)
R
I
L
R = External load (must be fitted)
U = 20 - 264V ~(ac) (50/60Hz)
I
OFF
< 4 mA at 20 °C (24 - 230 Vac)
I
OFF
< 6 mA at -40 to 80 °C (20 - 264 Vac)
I
L
= 20 - 500 mA
U = 20 - 60 V (dc
)
)
I
OFF
< 4 mA
IL = 20 - 500 mA
DPST
+V
= 5 A, 40 ms (inrush)
I PK
= 5 A, 40 ms (inrush)
I PK
= Load On
= Load Off
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1
U
N L
0V +V
Fuse
2A(T)
I
L
12V
DPST
Fuse
2A(T)
N L
0V +V
IL
<4mA
DPST
U
N L
0V +V
Fuse
2A(T)
IL12V
DPST
Fuse
2A(T)
N L
0V +V
IL
<4mA
DPST

November 2012
8
Manual Supplement
PNP/PLC electronics cassette (three-wire, yellow label)
High level Dry = ON Low level Wet = ON
PLC (positive input)PNP dc
LED on
continuously
LED flashes each
second LED on
continuously LED flashes each
second
OPERATION MODE
Dry On Mode
Dry
Wet
Wet On Mode
Dry
Wet
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
123
OUT
+-
4
PLC/PNP
Isolate Supply
Before Removing
PE
(Ground)
0VO/P
U = 20- 60 V (dc)
I < 4 mA +I
L
I
L ( MAX )= 0 -500 mA
U
OUT(ON)
= U - 2.5 Vac (20 °C)
I
L(OFF)
< 100A
+V
Fuse 2A(T)
= 5 A, 40 ms (inrush)
I PK
U
OUT(ON)
= U - 2.75 Vac (-40 to 80 °C)
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1
OUT
-
+
PLC
+
I/P
U
<3V I
L
OUT
-
+
PLC
+
I/P
I
L
<100 A
OUT
-
+
PLC
+
I/P
U
<3V I
L
OUT
-
+
PLC
+
I/P
I
L
<100 A
OUT
-
+
+
U
<3V
IL
Fuse
1A(T)
R
OUT
-
+
+
I
L
Fuse
1A(T)
R
< 100 A
OUT
-
+
+
U
<3V
IL
Fuse
1A(T)
R
OUT
-
+
+
I
L
Fuse
1A(T)
R
< 100 A

Manual Supplement
9
November 2012
Relay output electronics cassette (DPCO, green label)
High level Dry = ON Low level Wet = ON
LED on continuously LED flashes each
second LED on continuously LED flashes each
second
NC CNO NC NO
789
NOCNC
RELAY
123
LN
456
NOCNC
OPERATION MODE
Dry On
Dry
Wet
Wet On
Dry
Wet
Dry On Wet On
Seconds Delay
30
10
3
1
0.3 0.3
30
10
3
1
Isolate Supply Before RemovingWarning
C
Resistive Load
cos φ= 1 ;
L/R = 0 ms
ac
dc
Inductive Load
Fuse 0.5 (T)PE
(Ground)
DPST
N
0V +V
Live U = 20...264 V ~ (ac)
(50/60 Hz)
U = 20...60 V (dc)
I < 6 mA
I < 6 mA
IMAX = 5 A
UMAX = 250 V
PMAX = 1250 VA
UMAX = 30 V
PMAX = 240 W
cos φ= 0.4 ;
L/R = 7 ms
ac
dc
IMAX = 3.5 A
UMAX = 250 V
PMAX = 875 VA
UMAX = 30 V
PMAX = 170W
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1
NC NOC
NC NOCNC NOC
NC NOC
NC NOCNC NOC
NC NOC
NC NOC

November 2012
10
Manual Supplement
NAMUR electronics cassette (light blue label)
Note
This cassette is suitable for Intrinsically Safe applications and requires a certified
isolating barrier. See the Rosemount 2120 Reference Manual (00809-0100-4030)
for Intrinsically Safe approvals
This electronics cassette is also suitable for non-hazardous (safe) area applications.
It can only be interchanged with the 8/16 mA cassette.
Do not exceed 8 Vdc
High level Dry = ON Low level Wet = ON
LED on continuously LED flashes each
second
LED on continuously LED flashes each
second
OPERATION MODE
Dry On Mode
Dry
Wet
Wet On Mode
Dry
Wet
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
12
+-
EN 50227 / NAMUR
ION =2.2 ... 2.5 mA
IOFF = 0.8 ... 1.0 mA
+
-
A certified intrinsically safe
isolating amplifier to IEC 60947-5-6
Ex
Ex
8V
dc
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1
+
-
>2.2 mA
+
-
<1.0 mA
+
-
>2.2 mA
+
-
<1.0 mA

Manual Supplement
11
November 2012
8/16 mA electronics cassette (dark blue label)
Note
This cassette is suitable for Intrinsically Safe applications and requires a certified
isolating barrier. See the Rosemount 2120 Reference Manual (00809-0100-4030)
for Intrinsically Safe approvals
This cassette is also suitable for non-hazardous (safe) area applications. It can only be
interchanged with a NAMUR cassette
High level Dry = ON Low level Wet = ON
LED on continuously LED flashes each
second LED on continuously LED flashes each
second
OPERATION MODE
Dry On Mode
Dry
Wet
Wet On Mode
Dry
Wet
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
8/16 mA
12
3
+
Drives 4-20 mA Analog Input
I
ON
=
I
OFF
=
+
-
+
A certified intrinsically safe barrier
must be used to meet IS requirements
Ex
Ex
15 ... 17 mA
7.5 ... 8.5 mA
-
PE
(Ground)
U
=
11 - 30 V (dc)
Dry On Wet On
Seconds Delay
0.3 0.3
3
30
10
1
3
30
10
1
Dry On Wet On
Seconds Delay
0.3 0.3
30
10 3
30
10
1
3
1
+
> 15 mA
+
< 8.5 mA
+
> 15 mA
+
< 8.5 mA

November 2012
12
Manual Supplement
Troubleshooting
If there is a malfunction, see Table 1 for information on possible causes.
Table 1. Troubleshooting chart
LED indication
When the LED is red and flashing, it indicates the 2120 may be uncalibrated,
successfully calibrated, has an electrical load problem, or has an internal PCB fault.
See Table 2 for further information.
Table 2. LED flash rate
Fault Symptom/Indication Action/Solution
Does not
switch
No LED; no power Check the power supply; (check load on direct
load switching electronics model)
LED flashing See LED indication
Fork is damaged Replace the 2120
Thick encrustation on the fork Clean the fork with care
5 second delay when changing
mode/delay This is normal – wait 5 seconds
Incorrect
switching Dry = On, Wet = On set incorrectly Set the correct mode on the electronics cassette
Faulty
switching
Turbulence Set a longer switching time delay
Excessive electrical noise Suppress the cause of the interference
Cassette has been fitted from another
Rosemount 2120
Fit the factory supplied cassette (page 3)
and then calibrate (page 5)
LED Flash Rate Switch Status
Continuous Output state is on
1 every second Output state is off
1 every 2 seconds Uncalibrated – see “Calibration sequence” on page 5
1 every 4 seconds Load fault; load current too high; load short circuit
2 times every second Indication of successful calibration
3 times every second Internal PCB fault (microprocessor, ROM, or RAM)
Off Problem (e.g. supply)

Manual Supplement
13
November 2012

November 2012
14
Manual Supplement

Manual Supplement
15
November 2012

Rosemount Inc.
8200 Market Boulevard
Chanhassen, MN USA 55317
T (US) [phone]
T (Intnl) [phone]
F [phone]
Emerson Process Management
Asia Pacific Private Limited
1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947/65 6777 0743
Emerson Process Management
GmbH & Co. OHG
Argelsrieder Feld 3
82234 Wessling Germany
T 49 (8153) 9390, F49 (8153) 939172
Beijing Rosemount Far East
Instrument Co., Limited
No. 6 North Street, Hepingli,
Dong Cheng District
Beijing 100013, China
T (86) (10) 6428 2233
F (86) (10) 6422 8586
© 2012 Rosemount Inc. All rights reserved. All marks property of owner.
The Emerson logo is a trade mark and service mark of Emerson Electric Co
Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc.
Manual Supplement
00809-0200-4030, Rev BA
November 2012