Empire Comfort Systems LS-16C-2 Quick start guide

Page 1
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
LOG SET FOR UNVENTED
GAS LOG HEATER
OR
VENTED DECORATIVE APPLIANCE
MODELS
CHARRED OAK CHARRED OAK
SUPER SIZE
LS-16C-2
LS-18C2-1 LS-18C2S-1
LS-24C2-1 LS-24C2S-1
LS-30C2-1 LS-30C2S-1
WARNING: If not installed, operated and maintained
in accordance with the manufacturer's instructions,
this product could expose you to substances in fuel
or from fuel combustion which can cause death or
serious illness.
Log sets comply with ANSI Z21.11.2 Unvented Heaters
and also comply with ANSI Z21.60 Decorative Vented
Appliances for Solid Fuel Burning Fireplaces. State or
local codes may only allow operation of log sets in a
vented conguration. Check your state or local codes.
The White Mountain Log Collection
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
CHARRED OAK
CHARRED OAK SUPER SIZE
GAS-FIRED
The QR Codes below provide a link to our helpful “how-
to” videos. To get started, scan the code with your smart
phone or tablet.
Charred Oak Log Assembly Charred Oak Super Size
Log Assembly
WARNING: If the information in these instructions
are not followed exactly, a re or explosion may re-
sult causing property damage, personal injury or
loss of life.
— Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
re department.
— Installation and service must be performed by a
qualied installer, service agency or the gas sup-
plier.

25738-2-1013Page 2
Section Page
Important Installation Guidelines .....................................................................3
General Information .........................................................................................4
Requirements for Canada................................................................................5
Charred Oak Log Placement ...........................................................................6
Ember Placement LS-16C-2 Photos................................................................7
Ember Placement LS-18C2-1 Photos..............................................................8
Ember Placement LS-24C2-1 Photos..............................................................9
Ember Placement LS-30C2-1 Photos............................................................10
Charred Oak Super Size Log Placement....................................................... 11
Ember Placement LS-18C2S Photos ............................................................12
Ember Placement LS-24C2S Photos ............................................................13
Ember Placement LS-30C2S Photos ............................................................14
Charred Oak Parts List and Parts View .........................................................15
Charred Oak Super Size Parts List and Parts View.......................................16
Master Parts Distributor List...........................................................................17
How to Order Repair Parts ............................................................................17
Service Notes............................................................................................18-19
TABLE OF CONTENTS

25738-2-1013 Page 3
Proper Log Placement
Log placement is critical to proper burner performance. Logs
must be correctly positioned onto the burner. The photos in
this manual show the proper pinned position for logs on this
set. Owners need to be shown proper log placement and
instructed not to move the logs.
Logs must t rmly onto the burner when positioned as shown
in the photos. Malformed logs or logs with sloppy pin holes
must be replaced.
Proper Placement of Rock Wool and Decorative Lava Rock
Rock wool can be added to burners for a glowing ember
effect. It must be positioned only on the front portion of the
burner. The photos in this manual show the proper placement
of rock wool.
Decorative lava rock or small wood pieces should never be
placed on the burner. These items are only for placement on
the oor of the replace or rebox.
Proper Primary Airow into Burner
For proper burner operation and ame appearance, the ow
of primary air into the venturi tube, located on the rear of
the burner, must not be reduced. This ow of air is reduced
if dirt, lint or other obstructions build-up around or inside
the venturi. Any obstruction in the venturi tube area must
be removed. The ow of air into the venturi is also reduced
if the gas orice isn’t centered in the venturi inlet and/or is
not aligned with the venturi. Any misalignment of the burner
orice may be corrected by bending the shutter cap holding
the orice to the inlet of the venturi tube.
Ceiling Fans, Portable Fans or Logs Installed Near Cold
Air Returns
Ceiling fans or oscillating oor type fans need to be monitored
during the operation of vent-free logs. If the air blows directly
into the ame causing it to impinge on the log set, or rebox,
it should be turned off or redirected. Ceiling fans could be
reversed to possibly eliminate ame impingement, and the
oor fan could be redirected. Upon installation, be aware of
any cold air returns or vents in the proximity of the log set.
Any draft created around a vent-free log set can cause the
ame to impinge on the log and create a sooting situation.
WARNING: Do not allow fans to blow directly into the replace.
Avoid any drafts that alter burner ame patterns.
WARNING: Do not use a blower insert, heat exchanger insert
or other accessory not approved for use with this heater.
Candles
Avoid the use of scented or decorative candles while the log
set is in operation. Candles produce a residue in the air that
creates a soot like substance. Burning candles while the log
set is operating magnies the problem. It should be noted
that candles, in general, produce soot. The amount of time
burned and the quantity of candles burned will determine the
amount of soot produced and deposited.
Make Owners Aware of Proper Log Set Operation
Properly installed and properly maintained log sets do not
deposit soot on the logs. If users see soot appear on a log,
call for service. Do not continue to operate the log set.
Sunken Fireplace
If installing this unit into a sunken replace, you must raise
the oor to insure adequate airow and guard against sooting.
Raise replace oor using a non-combustible material, which
is secure.
Glass Doors
Make sure that glass doors are open during all operations of
the log set. The opening of the glass door frame should be the
dimension used for the minimum front opening of the rebox.
Woodburning Fireplaces
The interior of the rebox and the chimney should be cleaned
and free of all creosote before installing a gas burning log
set. Creosote will soften when heated and can drop on the
log set causing odors and possibly sooting.
WARNING: Before installing in a solid-fuel burning replace,
the chimney ue and rebox must be cleaned of soot, creosote,
ashes and loose paint by a qualied chimney cleaner.
IMPORTANT INSTALLATION GUIDELINES

25738-2-1013Page 4
Qualied Installing Agency
Installation and replacement of gas piping, gas utilization
equipment or accessories and repair and servicing of equip-
ment shall be performed only by a qualied agency. The term
"qualied agency" means any individual, rm, corporation,
or company that either in person or through a representa-
tive is engaged in and is responsible for (a) the installation,
testing, or replacement of gas piping or (b) the connection,
installation, testing, repair, or servicing of equipment; that is
experienced in such work; that is familiar with all precautions
required, and that has complied with all the requirements of
the authority having jurisdiction.
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA54.*
*Available from the American National Standards Institute, Inc. 11 West
42nd St., New York, N.Y. 10018.
State of Massachusetts: The installation must be made by
a licensed plumber or gas tter in the Commonwealth of
Massachusetts.
Sellers of unvented propane or natural gas-red supple-
mental room heaters shall provide to each purchaser a
copy of 527 CMR 30 upon sale of the unit.
In the State of Massachusetts, unvented propane and
natural gas-red space heaters shall be prohibited in bed-
rooms and bathrooms.
GENERAL INFORMATION

25738-2-1013 Page 5
REQUIREMENTS FOR CANADA
This unit cannot be installed in a UNVENTED application,
this unit can only be installed as a VENTED application
with these requirements.
IMPORTANT SAFETY INFORMATION
This unit complies with ANSI Z21.60and CGA 2.26 Decora-
tive Gas Appliances For Installation In Solid Fuel Burning
Fireplaces. Do not burn wood or solid fuels in a replace
where a decorative gas log set is installed. This appliance is
for installation only in a solid fuel burning replace, masonry
replace or manufactured replace.
Warning: Any modication to this gas log set or to controls
can be dangerous. Improper installation or use of the gas
log set can cause serious injury or death from re, burns,
explosion or carbon monoxide poisoning.
1. Please follow all local codes regarding installation,
combustion and ventilation air or in the absence of
local codes follow the National Fuel Gas Code ANSI
Z223.1(U.S. installation), or CAN/CGA-B149, Installa-
tion Code (Canada installation).
2. Proper installation, burner pan location and log place-
ment is important to achieve optimum look and per-
formance of your gas log set. The logs have been de-
signed for easy location and placement on the grate
and must be followed for proper operation.
3. Do not operate this log set with glass doors in the closed
position. A replace screen must be in place when the
log set is burning. Adequate combustion air must be
provided for proper venting. All ames should go up and
out the top of the rebox into the ue vent. If any ames
oat or curl forward into the room do not operate appli-
ance. Check for an open ue and adequate combustion
air into the room. A damper clamp must be installed on
the rebox damper to maintain an open ue vent condi-
tion. Refer to replace owners manual INSTALLING
DAMPER CLAMP section.
4. Young children must be carefully supervised when they
are in the same room as the gas log while in operation.
Do not place stockings, clothing or any ammable ma-
terial above or near the replace.
5. Do not substitute or use materials other than those sup-
plied for use with the log set.
6. Also refer to IMPORTANT SAFETY INFORMATION in
the replace Owner's Manual.
WARNING; DO NOT OPERATE THIS GAS LOG SET
WITH GLASS DOORS CLOSED
• Clothing or other ammable material should not be
placed on or near the appliance.
• Do not place trash or other articles on the log set during
operation.
• During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain
oils, lms or bonding agents. These bonding agents
are not harmful but may produce annoying smoke and
smells as they are burned off during initial operation of
the appliance. This is a normal temporary occurrence.
A window should be opened during the initial bake out
period.
• Keep burner and control compartment clean.
• WARNING: Before installing in a solid fuel burning re-
place, the chimney ue and rebox must be cleaned
of soot, creosote, ashes and loose paint by a qualied
chimney cleaner.
• Installation and repair should be done by a qualied
service person. The appliance should be inspected
before use and at least annually by a qualied service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding materials, etc. It
is imperative that control compartments, burners and
circulating air passageways of the appliance be kept
clean.
• Do not put anything around the replace that will ob-
struct the ow of ventilation air.
• Do keep the appliance area clear and free from com-
bustible material, gasoline and other ammable vapors
and liquids.
• A yearly examination and cleaning of the venting system
of the solid-fuel burning replace must be performed by
a qualied agency.
• Do make a periodic visual check of pilot and burners.
Clean and replace damaged parts.
• Do not use this appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been un-
der water.
• Never burn solid fuels in replace where a gas log set is
installed.
• This unit complies with ANSI Z21.60 Decorative Vented
Appliances for Solid Fuel Burning Fireplaces. State or
local codes may only allow operation of this appliance
in a vented conguration. Check your state or local
codes.

25738-2-1013Page 6
CHARRED OAK LOG PLACEMENT
Before you begin: Do not, handle these logs with your bare hands!
Always wear gloves to prevent skin irritation. After handling logs,
wash your hands gently with soap and water.
All Logs
The positioning of the logs is critical to the safe and clean operation
of this heater. Sooting and other problems may result if the logs are
not properly and rmly positioned in the appliance.
Refer to Figure 1 and Figure 1A for the following warning.
Warning: Failure to position the parts in accordance with this
diagram or failure to use only parts specically approved with
this appliance may result in property damage or personal injury.
PROPER INSTALLATION SEQUENCE:
LS-(18,24,30)C2-1:
(Figure 1)
1. Place rear (#1) log onto two (2) pins on rear log support.
2. Place left, front (#2) log onto two (2) left, front pins on burner
pan.
3. Place right, front (#3) log onto two (2) right, front pins on burner
pan.
4. Place Y Branch (#4) onto two (2) pins on rear log.
5. Compare the completed log installation with the appropriate
photo from pages 8 through 10. Review previous steps to make
any necessary adjustments.
6. Log placement is completed.
PROPER INSTALLATION SEQUENCE:
LS-16C-2
(Figure 1A)
1. Place rear (#4) log onto right, rear pin on rear log support.
2. Place middle (#1) log between rear log support and burner pan.
3. Place left, front (#2) log onto two (2) left, front pins on burner
pan.
4. Place right, front (#3) log onto two (2) right, front pins on burner
pan.
5. Compare the completed log installation with the appropriate
photo from page 7. Review previous steps to make any
necessary adjustments.
6. Log placement is complete.
Attention: Do not use Figure 1 or Figure 1A to order replacement
logs. Refer to Page 15 Parts List and Parts View to order logs for
your appropriate model number.
Apply loose material (glowing embers) per appropriate Installation
Instructions and Owner's Manual. Replacement of loose material
(glowing embers) must be purchased from Empire Comfort Systems,
Inc. Application of excess loose material (glowing embers) may
adversely affect performance of the heater.
WARNING: All previously applied loose material must be removed
prior to reapplication.
Replacement Loose Material (glowing embers) Part Number
LS-16C and CHBR 15998
LS-18C 15999
LS-24C 15970
LS-30C 15970
Platinum Bright Embers PE-20-1
Note: A single layer of embers is to be used when applying
Platinum Bright Embers (alone or in combination with production
embers) to the burner.
1
2
3
4
Log Placement LS-(18,24,30)C2-1
Figure 1
Log Placement LS-16C-2 and CHBR
Figure 1A
The following WARNING applies when log set is installed onto an
unvented gas burner assembly.
WARNING: This appliance is equipped for (natural or
propane) gas. Field conversion is not permitted.
Scan this code to see the log assembly video.

25738-2-1013 Page 7
Photo 1
Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers).
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-16C-2 AND CHBR PHOTOS

25738-2-1013Page 8
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers)
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-18C2 PHOTOS

25738-2-1013 Page 9
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers)
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-24C2 PHOTOS

25738-2-1013Page 10
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers)
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-30C2 PHOTOS

25738-2-1013 Page 11
CHARRED OAK SUPER SIZE LOG PLACEMENT
Before you begin: Do not, handle these logs with your bare hands!
Always wear gloves to prevent skin irritation. After handling logs,
wash your hands gently with soap and water.
All Logs
The positioning of the logs is critical to the safe and clean operation
of this heater. Sooting and other problems may result if the logs are
not properly and rmly positioned in the appliance.
Refer to Figure 1 for the following warning.
Warning: Failure to position the parts in accordance with this
diagram or failure to use only parts specically approved with
this appliance may result in property damage or personal injury.
PROPER INSTALLATION SEQUENCE:
LS-(18,24,30)CS
(Figure 1)
1. Place rear (#1) log onto two (2) pins on rear log support.
2. Place left, front (#2) log onto two (2) left, front pins on burner
pan.
3. Place right, front (#3) log onto two (2) right, front pins on burner
pan.
4. Place Y Branch (#4) onto two (2) pins on rear log.
5. Place left, top log (#6) onto two (2) pins on rear log left.
6. Place right, top log (#5) onto two (2) pins on rear log right.
7. Compare the completed log installation with the appropriate
photo from pages 12 through 14. Review previous steps to
make any necessary adjustments.
8. Log placement is completed.
Attention: Do not use Figure 1 to order replacement logs. Refer to
Page 16 Parts List and Parts View to order logs for your appropriate
model number.
Apply loose material (glowing embers) per appropriate Installation
Instructions and Owner's Manual. Replacement of loose material
(glowing embers) must be purchased from Empire Comfort Systems,
Inc. Application of excess loose material (glowing embers) may
adversely affect performance of the heater.
WARNING: All previously applied loose material must be removed
prior to reapplication.
Replacement Loose Material (glowing embers) Part Number
LS-18C2S 15999
LS-24C2S 15970
LS-30C2S 15970
Platinum Bright Embers PE-20-1
Note: A single layer of embers is to be used when applying Platinum
Bright Embers (alone or in combination with production embers)
to the burner.
1
2
3
4
5
6
Log Placement
LS-(18,24,30)CS
Figure 1
The following WARNING applies when log set is installed onto an
unvented gas burner assembly.
WARNING: This appliance is equipped for (natural or
propane) gas. Field conversion is not permitted.
Scan this code to see the log assembly video.

25738-2-1013Page 12
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers)
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-18C2S PHOTOS

25738-2-1013 Page 13
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large rear ports with
loose material (glowing embers)
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-24C2S PHOTOS

25738-2-1013Page 14
Do not cover any large rear ports with
loose material (glowing embers)
Photo 1 Photo 2
Photo 3 Photo 4
Do not cover any large front ports with
loose material (glowing embers)
EMBER PLACEMENT LS-30C2S PHOTOS

25738-2-1013 Page 15
Attention: When ordering parts, it is very important that part number and description of part coincide.
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
1
2
3
4
Index
No.
Part
Number Description
CHARRED OAK LOG SETS
LS-18C2
1 R-8301 REAR LOG
2 R-8299 LEFT FRONT LOG
3 R-8300 RIGHT FRONT LOG
4 R-8302 Y BRANCH
LS-24C2
1 R-8306 REAR LOG
2 R-8304 LEFT FRONT LOG
3 R-8305 RIGHT FRONT LOG
4 R-8307 Y BRANCH
LS-30C2
1 R-8310 REAR LOG
2 R-8308 LEFT FRONT LOG
3 R-8309 RIGHT FRONT LOG
4 R-8311 Y BRANCH
LS-16C-2, CHBR-16
1 R-7465 LEFT FRONT LOG
2 R-7466 RIGHT FRONT LOG
3 R-7467 MIDDLE LOG
4 R-7468 REAR LOG
1
2
3
4
CHARRED OAK PARTS LIST & PARTS VIEW

25738-2-1013Page 16
Attention: When ordering parts, it is very important that part number and description of part coincide.
USE ONLY MANUFACTURER'S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
1
2
3
4
5
6
Index
No.
Part
Number Description
CHARRED OAK SUPER SIZE LOG SETS
LS-18C2S
1 R-9182 REAR LOG
2 R-8299 LEFT FRONT LOG
3 R-8300 RIGHT FRONT LOG
4 R-8302 Y BRANCH
5 R-8312 RIGHT TOP LOG
6 R-8313 LEFT TOP LOG
LS-24C2S
1 R-9183 REAR LOG
2 R-8304 LEFT FRONT LOG
3 R-8305 RIGHT FRONT LOG
4 R-8307 Y BRANCH
5 R-8315 RIGHT TOP LOG
6 R-8316 LEFT TOP LOG
LS-30C2S
1 R-9184 REAR LOG
2 R-8308 LEFT FRONT LOG
3 R-8309 RIGHT FRONT LOG
4 R-8311 Y BRANCH
5 R-8317 RIGHT TOP LOG
6 R-8318 LEFT TOP LOG
CHARRED OAK SUPER SIZE PARTS LIST & PARTS VIEW

25738-2-1013 Page 17
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equip-
ment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
MASTER PARTS DISTRIBUTOR LIST
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distribu-
tors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
All parts listed in the Parts List have a Part Number. When ordering parts, rst obtain the Model Number and Serial Number from the
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the fol-
lowing illustration and part list. Be sure to give all this information . . .
Appliance Model Number Part Description
Appliance Serial Number Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, res and all causes beyond our control.
HOW TO ORDER REPAIR PARTS
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
Phone: [phone]
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater, Hearth and Grills
Victor Division of F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: [phone]
Toll Free: 800-243-9360
Fax: [phone]
Toll Free Fax: [phone]
Websites: www.fwwebb.com & www.victormfg.com
Parts: Heater, Hearth and Grills
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Phone: [phone]
Toll Free: 800-755-8809
Fax: [phone]
Website: www.eastcoastenergy.com
Parts: Heater, Hearth and Grills
Able Distributors
2501 North Central Avenue
Chicago, IL 60639
Phone: [phone]
Toll Free: 800-880-2253
Fax: [phone]
Website: www. abledistributors.com
Parts: Heater

25738-2-1013Page 18
APPLIANCE SERVICE HISTORY
Date Dealer Name Service Technician Name Service Performed/Notes

25738-2-1013 Page 19
APPLIANCE SERVICE HISTORY
Date Dealer Name Service Technician Name Service Performed/Notes

25738-2-1013Page 20
EMPIRE
EMPIRE
Comfort Systems
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
If you have a general question about our products, please e-mail us at
[email protected].
If you have a service or repair question, please contact your dealer.
www.empirecomfort.com