Enable-IT 865 PTZQ PRO User manual

All Rights Reserved 1997 - 2015 ENABLE-IT-Proprietary and Confidential
Enable-IT 865 PTZQ Pro
Rev B High Powered PoE+
Ethernet Extender
User Manual

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 2 of 16
Copyright © 1997-2015 Enable-IT, Inc. All rights reserved. No part of this
documentation may be reproduced in any form, or by any means, or used to make any
derivative work (such as translation, transformation, or adaptation) without written
permission from Enable-IT, Inc.
Enable-IT, Inc. reserves the right to revise this documentation and to make changes in
content from time to time without obligation on the part of Enable-IT, Inc., to provide
notification of such revision or change.
Enable-IT, Inc. provides this documentation without warranty, term, or condition of any
kind, either implied or expressed, including, but not limited to, the implied warranties,
terms or conditions of merchantability, satisfactory quality, and fitness for a particular
purpose. Enable-IT, Inc. may make improvements or changes in the product(s) and/or
the program(s) described in this documentation at any time.
If there is any software on removable media described in this documentation it can be
provided on request. Please contact Enable-IT, Inc. and a copy will be provided to you.
UNITED STATES GOVERNMENT LEGEND
If you are a United States government agency, then this documentation and the
software described herein are provided to you subject to the following:
All technical data and computer software are commercial in nature and developed solely
at private expense. Software is delivered as "Commercial Computer Software" as
defined in DFARS 252.227-7014 (June 1995) or as a "commercial item" as defined in
FAR 2.101 (a) and as such is provided with only such rights as are provided in Enable-
IT, Inc.'s standard commercial license for the software/firmware.
Technical data is provided with limited rights only as provided in DFAR 252.227-7015
(Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to
remove or deface any portion of any legend provided on any licensed program or
documentation contained in, or delivered to you in conjunction with, this User Manual.
Unless otherwise indicated, Enable-IT, Inc. registered trademarks are registered in the
United States and may, or may not, be registered in other countries

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 3 of 16
TABLE OF CONTENTS
ABOUT THIS USER MANUAL......................................................................................4
INTRODUCING THE 865 PTZQ PRO EXTENDED POEAND ETHERNET KIT............5
About The 865 PTZQ PRO EXTENDED PoE and ETHERNET KIT........... 5
Key Benefits ................................................................................................6
Summary Of Features.................................................................................6
Multi Use Applications.................................................................................7
INSTALLING THE 865 PTZQ PRO EXTENDED POEAND ETHERNET KIT...............8
Site Plan – Installation Design Considerations............................................8
Unpacking the Enable-IT 865 PTZQ PRO KIT............................................9
Perform An Out Of The Box Test (OOTBT).................................................9
Performing The On-Site Installation ............................................................10
Mounting the 865 PTZQ PRO KIT...............................................................10
Building the 865 PTZQ PRO Interlink Wiring...............................................10
Cabling Devices to the Enable-IT 865PTZQ PRO Kit .................................10
Troubleshooting...........................................................................................11
Performance Settings (DIP Switch).............................................................12
TECHNICAL SUPPORT ...............................................................................................13
Online Technical Services...........................................................................13
World Wide Web Site ..................................................................................13
Returning Products for Warranty Repair .....................................................13
Returning Products for Refund....................................................................13
ENABLE-IT,INC.LIMITED WARRANTY........................................................................14
CONTACT US............................................................................................................16

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 4 of 16
ABOUT THIS USER MANUAL
This product User Manual provides all the information needed to install and use the
Enable-IT 865 PTZQ PRO EXTENDED PoE and ETHERNET KIT. This User Manual is
intended for use by technicians who are responsible for installing and setting up network
equipment. Consequently, it is assumed that the installer has a basic working
knowledge of LANs (Local Area Networks), PoE (Power-over-Ethernet) and voice
telecom wiring.
Most Enable-IT documents are available in Adobe Acrobat Reader Portable Document
Format (PDF) or HTML on the Enable-IT’s website under the Support tab.

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 5 of 16
INTRODUCING THE 865 PTZQ PRO KIT
Congratulations on purchasing the Enable-IT 865 PTZQ PRO EXTENDED PoE and
ETHERNET KIT — the simplest method to install your High Powered PoE PTZ Security
cameras using Ethernet or telephone wiring. This is the world’s first solution to deliver
Voice, Ethernet Data and Power over Ethernet (PoE) in a combined package that
exceeds the IEEE distance limitations for all Ethernet equipment.
WARNING: Output LAN ports 1 & 2 on the 865 PTZQ PRO CPE are PoE enabled and
not for use with non-PoE equipment as it may damage any non-PoE equipment.
This chapter contains introductory information about how it can be used in your network
and covers the following topics:
•About the 865 PTZQ PRO Extended PoE and Ethernet Kit
•Key Benefits
•Summary of Features
•Typical Use Applications
About the 865 PTZQ PRO Extended PoE and Ethernet Kit
The 865 PTZQ PRO Extended PoE and Ethernet Kit provides a complete all in one
solution and lower cost alternative for installing a PoE device beyond IEEE Ethernet cabling
distance limitations or for installing a remote LAN requiring no power at the remote end.
Traditional methods require installation of costly fiber (that can’t carry power) or a series
of hubs/repeaters and the use of voice and PoE equipment combined.
The preferred network access for these PoE devices is a dedicated Ethernet line,
however Ethernet over twisted pair wiring has its distance limitations of just 328 ft. In
order to drive Ethernet signal further, one would have to add repeaters to each
segment of 328ft twisted pair cabling; this is often insufficient and too costly in multi-
story buildings. Fortunately the Enable-IT 865 Series Extended Ethernet extends
High Power PoE+ and 100Mbps Ethernet up to 4.5 times beyond the 328ft/100m limit up
to 1,500ft/458m distance. If using the PoE to remotely power the 865 CPE (remote
device) and using standalone remote self-powered LAN than it will extend Ethernet data
up to 3,500ft/1,067m distance using LAN ports 3-4 output.
The 865 PTZQ PRO enables the simple installation of a PTZ PoE+ device up to 1,500ft
(458m) from your LAN and Power Source. – This is ideal for installing High Powered
PoE+ PTZ Security cameras or for a standalone remote self powered LAN up to 3,500ft
(1,067m).
WARNING: Output LAN ports 1 & 2 on the 865 PTZQ PRO CPE are PoE enabled and
not for use with non-PoE equipment as it may damage any non-PoE equipment.
The Enable-IT 865 PTZQ PRO Extended Poe and Ethernet kit has been tested to provide full
duplex transport up to 100MB/s over 2-pair telephone wiring or better.
Key Benefits
Unit Model
Wiring
Min Data Rate
Max. Distance
865PTZQ CAT3, CAT5e or better
100Mbps FD*
1,500ft / 458m

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 6 of 16
The following list identifies the 865 PTZQ PRO Extended PoE and Ethernet Kit key
benefits.
•Quad switched PoE+ enabled LAN RJ-45 10/100 Ethernet ports on each end for
expansion without adding a hub or switch on each end.
•The Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit requires No
Power (CPE remote end), No Firmware, No Maintenance
•Broadband technology that delivers in-building PoE+ and Ethernet access over
existing Category 3 , Category 5e wiring or better up to 1,500ft or 458m.
•Provides one scalable infrastructure for Internet access, dual POTS, VoIP, video,
Power over Ethernet (PoE) and virtual private networking.
•Low profile box with voice line, Ethernet data and PoE+ all in a single RJ-45
Ethernet jack (Interlink port).
Summary of Features
The Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit has the following
hardware features:
•PoE and Extended Ethernet line over existing CAT 3 up to CAT5e / CAT6 wiring
•Uses RJ-45 Interlink port for transport (single voice, PoE and 100Mbps data)
•Rapid Telco style installation – no programming required
•Supports digital VoD channels and Maintains existing telephone (lifeline POTS)
•Drives Ethernet 100 Mbps full-duplex service delivery with PoE up to 3,500ft or 1,067m
•Network Equipment independence – Transparent to protocols/applications/MAC
•Cisco PoE single line injector support built in.
•Transparent to single line 802.3af PoE devices.
Specifications: Functionality:
Power Indicator Data Rates 100Mbps Full Duplex
100Mbps Link status/Activity Full Duplex/Half Duplex status/Collisions
VDSL2 Link Status/Activity Protocol independent
Dimensions: 865 PTZQ PRO Interlink port pins:
Height: 1.5" (38mm) Pins 1 & 2 – Data
Depth: 3.75" (95mm) Pins 3, 4 & 5 – PoE positive power
Width: 5.75” (146mm) Pins 6, 7 & 8 – PoE negative power
Interfaces Environment
(1) 5v 2A DC Power Adapter 2.1mm Operating temp: -49°F to 168°F ( -45°to 7 6°C)
(4) RJ-45 100MB LAN Auto negotiate Port Storage temp: -49°F to 168°F ( -45°to 76°C)
(1) RJ-45 Interlink Port Humidity 5% to 95%, non-condensing
LAN 1 port pins:
Pins 1, 2, 3 & 6 – Ethernet Data
Pins 4 & 5 – PoE positive power
Pins 7 & 8 – PoE negative power
Multi Use Applications

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 7 of 16
Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit is a versatile multipurpose
solution installed for the use of PoE equipment such as High Powered PoE+ PTZ
Cameras. Non-PoE equipment may be damaged if used and the Enable-IT 865 PTZQ
PRO kit should be used to bridge non-PoE equipment.
The 865 PTZQ PRO Extended PoE and Ethernet Kit allows a standard Ethernet
segment injected with 56v PoE+ to be deployed quickly over existing 2 pair Telco
Copper Wiring or CAT5e cabling up to 1,500ft / 458m to a remote unpowered location.
Installers have the convenience of a 100Mbps LAN Ethernet unit for peace of mind
connectivity and no device maintenance. Rapid installation allows for minimal
interruption and the Broadband technology allows for investment protection up to 10-15
years with no firmware or replacement issues. Bandwidth can be scaled according to
the Broadband Access Provider needs. The 865 PTZQ PRO Extended PoE and
Ethernet Kit is a passive device so interruption of Internet service does not affect POTS
services. Carriers and Access Providers can come and go, but the 865 PTZQ PRO
Extended PoE and Ethernet Kit technologies continue to provide lasting value such as
the other utilities like water, gas and electricity.
The Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit is suited for the following key
environments:
•Commercial Buildings (Multi-Tenant Units)
•Business Parks (Multi-Tenant Units)
•Apartments (Multi-Residential Units)
•Hotels (Multi-Hospitality Units)
•Business Suites (Multi-Hospitality Units)
•School Campuses (University, K-12)
•College Housing (Multi-Residential Units)
•Mining Operations – Quarries, Mine shafts
•Nautical Infrastructure – Cruise ships, Marinas, dive operations, subs
•Video Surveillance/Security
•WiFi Deployment – ISP’s, RV Parks, Construction sites
•Manufacturing – Foundries, pharmaceutical, aerospace, automotive,
petroleum, concrete plants, etc.
•Retail POS – Department stores, Bars, restaurants, retail spaces
•Government – Naval ships, FEMA, Housing, USGS, National Parks, Forestry,
Research stations, NASA, utilities, etc.
•Education – outdoor camps, college campuses
•Healthcare – Hospitals, elder care, outpatient facilities
•Entertainment – Movie theaters, home entertainment, fairs, outdoor venues
INSTALLING THE 865 PTZQ PRO KIT

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 8 of 16
The Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit has a distance restriction
of 1,500ft or 458m over 2-pair of Category 3 up to 4-pair Category 5e / CAT6 wiring from
your LAN and power source to the remote PoE device. Therefore quick, simple site
surveys and installation planning are highly recommended – This is ideal for installing PoE
IP Security cameras or PoE WiFi Access Points.
This chapter describes the recommended installation process for the Enable-IT 865
PTZQ PRO Extended PoE and Ethernet Kit. It covers the following topics:
•Site Plan – Installation Design Considerations
•Unpacking the Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit
•Perform an out of the box Test
•Performing the On-Site Installation
Site Plan - Installation Design Considerations
The planning process should involve a site walkthrough and discovery survey. Electrical
Cable measurement tools are the most reliable method to determine the longest run of
hidden wiring. Estimate the best locations to position the Broadband Concentrators to
adequately reach desired connectivity on each floor. Document your findings to use in
designing a network topology to support the Ethernet Switches and backbone
connectivity. Key points to remember in the Site Survey.
•Total distance limitation of 1,500ft / 458m from end to end.
•2 Pair CAT-3 wiring or 4-pair Cat5e .30 Gage or better cabling is required for the
865 PTZQ PRO Interlink transmission.
•Not compatible with any PoE switches as the PoE switches are not smart enough
to understand Extender Ethernet timing mechanisms and fail to set correct output
voltage and will subsequently disable the PoE switch port.
•Transparent to single line 802.3at PoE injectors and devices.
For CAT3 wiring (2-pair/4 wires) you will need to crimp a RJ-45 Male Head to each
end of the contiguous wire run and using the following pins(1,2,4 or 5, 7 or 8) straight
through. This will deliver Ethernet Data and PoE.
For CAT5e or better wiring (4-pair/8 wires) you will need to crimp a RJ-45 Male Head
to each end of the contiguous wire run and using the following pins(1,2,3,4,5,6,7 & 8)
straight through. This will deliver Ethernet Data and PoE. This can be either T-568A
or T-568B spec.
Unpacking the Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit
865 PTZQ PRO CO

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 9 of 16
Carefully remove the Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit all
packing materials from the box. Verify that the items listed below are present. Make sure
that the equipment supplied matches what you ordered. If any items are missing or
damaged, please contact Enable-IT or your distributor for assistance.
•(2) The Enable-IT 865 PTZQ PRO & Extended Ethernet Units (CO & CPE)
o5v AC/DC Power adapter for 865 PTZQ CO
o10’ LAN patch cables
oEnable-IT 375 75W - 56v High Power PoE+ Injector
•(1) Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit User Manual
Perform an out of the box Test
We highly recommend a quick test to ensure the working order of your 865 PTZQ PRO
units. To do this, please use one of the Ethernet patch cords provided and attach to the
865 PTZQ Interlink port on each 865 PTZQ unit.
Using the 5v power adapter, power up the 865 PTZQ PRO CO Unit and run another
Ethernet patch cord from LAN2/PoE on the 865 PTZQ PRO CO to LAN2/PoE on the 865
PTZQ PRO CPE. Next you will need to connect your PTZQ camera to the LAN1/PoE port
on the 865 PTZQ PRO CPE.
The last step is to then connect the 375 PoE Injector to the LAN1/PoE port on the 865
PTZQ PRO CO. After a few seconds you should see a solid Green Interlink Sync LED on
each unit to confirm a link is established. The Green Interlink Sync LED will pulse rapidly
as it detects traffic. This confirms basic proper operation of the units.
WARNING: Output LAN ports 1 & 2 on the 865 PTZQ PRO CPE are PoE enabled and
not for use with non-PoE equipment as it may damage any non-PoE equipment.

All Rights Reserved 1997 - 2015 Enable-IT, Inc. Page 10 of 16
LED indicators will provide visual operational status of the 865 PTZQ PRO units.
Mode – Yellow Solid LED
Off = CO unit
On = CPE unit
Sync – Green slow to fast flicker LED on power up – indicates negotiation of a link
– Green solid LED indicates link established and rapid pulse is traffic
Act – Yellow LED
Off = No device attached or detected
On = Solid, indicates the presence of local LAN
On = Blinking, indicates the presence of local LAN traffic
Pwr – Green Solid LED indicates the unit is receiving 5v power
Performing the On-Site Installation
After removing the Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit from the
box and performing the out of the box testing all that remains to install the unit on-site is
to mount the unit, build the interconnect wiring, add voice lines if needed and attach the
LAN device cabling with the provided Ethernet Patch cords.
Mounting the Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Units
The Enable-IT 865 PTZQ PRO Extended PoE and Ethernet Kit is designed for quick
wall mounting. Choose a location to mount each of the Enable-IT 865 PTZQ’s
where the maximum distance does not exceed 1,500ft or 458m total between
devices to be connected. When mounting the Enable-IT 865 PTZQ PRO Extended
PoE and Ethernet Kit it is recommended that you use the appropriate anchors for
your mounting surface. If mounting on plywood use wood screws; if mounting onto
drywall or sheetrock, use plastic drywall anchors or Velcro can also be used as the
units are very lightweight.
Building the 865PTZ Q PRO Interlink wiring
The most important aspect of the install is the correct wiring of the Interlink cabling.
For CAT3 wiring (2-pair/4 wires) you will need to crimp a RJ-45 Male Head to each
end of the contiguous wire run and using the following pins(1,2,4 or 5, 7 or 8) straight
through. This will deliver Ethernet Data and PoE.
For CAT5e or better wiring (4-pair/8 wires) you will need to crimp a RJ-45 Male Head
to each end of the contiguous wire run and using the following pins(1,2,3,4,5,6,7 & 8)
straight through. This will deliver Ethernet Data and PoE. This can be either T-568A
or T-568B spec.
Attaching cabling and devices to the Enable-IT 865 PTZQ PRO Extended PoE and
Ethernet Kit. Attach your remote PoE device to the 865 PTZQ PRO CPE unit
LAN/PoE ports with Ethernet patch cord provided. Attach your local LAN to the 375
PoE injector Data IN port. Attach the power adapter to the 865 PTZQ CO unit. Attach
the 375 PoE+ injector to the 865 PTZQ PRO CO LAN1/PoE port with Ethernet patch
cord provided. Apply power to the 375 PoE injector with the country power cord
provided. Your equipment should now be powered up and functioning properly.