Enable-IT 820P Pro User manual

All Rights Reserved 1997 - 2013 ENABLE-IT- Proprietary and Confidential
Enable-IT 820P Pro
Ethernet Extender Kit
User Manual



All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 2 of 14

Copyright © 1997-2013 Enable-IT, Inc. All rights reserved. No part of this documentation
may be reproduced in any form, or by any means, or used to make any derivative work
(such as translation, transformation, or adaptation) without written permission from
Enable-IT, Inc.
Enable-IT, Inc. reserves the right to revise this documentation and to make changes in
content from time to time without obligation on the part of Enable-IT, Inc., to provide
notification of such revision or change.
Enable-IT, Inc. provides this documentation without warranty, term, or condition of any
kind, either implied or expressed, including, but not limited to, the implied warranties,
terms or conditions of merchantability, satisfactory quality, and fitness for a particular
purpose. Enable-IT, Inc. may make improvements or changes in the product(s) and/or
the program(s) described in this documentation at any time.
If there is any software on removable media described in this documentation it can be
provided on request. Please contact Enable-IT, Inc. and a copy will be provided to you.
UNITED STATES GOVERNMENT LEGEND
If you are a United States government agency, then this documentation and the software
described herein are provided to you subject to the following:
All technical data and computer software are commercial in nature and developed solely
at private expense. Software is delivered as "Commercial Computer Software" as defined
in DFARS 252.227-7014 (June 1995) or as a "commercial item" as defined in FAR 2.101
(a) and as such is provided with only such rights as are provided in Enable-IT, Inc.'s
standard commercial license for the software/firmware.
Technical data is provided with limited rights only as provided in DFAR 252.227-7015
(Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to
remove or deface any portion of any legend provided on any licensed program or
documentation contained in, or delivered to you in conjunction with, this User Manual.
Unless otherwise indicated, Enable-IT, Inc. registered trademarks are registered in the
United States and may, or may not, be registered in other countries

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 3 of 14

TABLE OF CONTENTS
ABOUT THIS USER MANUAL...................................................................................... 4
INTRODUCING THE 820P PRO ETHERNET EXTENDER KIT ........................................... 5
About The 820P Pro Ethernet Extender Kit................................................. 5
Key Benefits ................................................................................................ 6
Summary Of Features ................................................................................. 6
Typical Use Applications ............................................................................. 7
INSTALLING THE 820P PRO ETHERNET EXTENDER KIT .............................................. 8
Site Plan – Installation Design Considerations............................................ 8
Perform An Out Of The Box Test (OOTBT)................................................. 8
Performance Settings (DIP Switch)............................................................. 9
Unpacking the Enable-IT 820P Pro Ethernet Extender Kit.......................... 10
Performing the On-Site Installation.............................................................. 10
Mounting the 820P Pro Ethernet Extender.................................................. 10
Building the 820P Pro Wiring....................................................................... 10
Cabling Devices to the Enable-IT 820P Pro Extended Ethernet Kit............ 10
Troubleshooting........................................................................................... 11
TECHNICAL SUPPORT ............................................................................................... 11
Online Technical Services........................................................................... 11
World Wide Web Site .................................................................................. 11
Returning Products for Warranty Repair ..................................................... 11
Returning Products for Refund.................................................................... 12
ENABLE-IT, INC.LIMITED WARRANTY........................................................................ 12
CONTACT US............................................................................................................ 14

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 4 of 14

ABOUT THIS USER MANUAL
This product User Manual provides all the information needed to install and use the
Enable-IT 820P Pro Ethernet Extender Kit. This User Manual is intended for use by
technicians who are responsible for installing and setting up network equipment.
Consequently, it is assumed that the installer has a basic working knowledge of LANs
(Local Area Networks), PoE (Power-over-Ethernet) and voice telecom wiring.
Most Enable-IT documents are available in Adobe Acrobat Reader Portable Document
Format (PDF) or HTML on the Enable-IT’s website under the Support tab.

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 5 of 14

INTRODUCING THE 820P PRO ETHERNET EXTENDER KIT
Congratulations on purchasing the Enable-IT’s 820P Pro 820P Pro IP PoE Camera Extender Kit
— the simplest method to stretch your broadband solutions for in-building deployment in
commercial office buildings, hotels, and multi-tenant residential units.
The 820P IP PoE Camera Extender Kit offers the Lowest Cost Solution in a simple design
for rapid install using existing 4 pair Telco wiring.
This chapter contains introductory information about the 820P Pro Extended Ethernet Kit
and how it can be used in your network. It covers the following topics:
About the 820P Pro Extended Ethernet Kit
Key Benefits
Summary of Features
Typical Applications
DO NOT INSERT ANY BLANK RJ-45 HEADS INTO ANY PORTS BEFORE CRIMPING
– OTHERWISE YOU WILL RENDER THE PORT USELESS – BENT PINS
About the 820P Pro Extended Ethernet Kit
The 820P Pro IP PoE Camera Extender Kit solves the problem of high costs associated
with stretching your backbone with traditional fiber or a series of hubs/repeaters.
In many office buildings, preferred network access is a dedicated Ethernet line,
however Ethernet over twisted pair wiring has its distance limitations of just 328 ft. In
order to drive Ethernet signal further, one would have to add repeaters to each
segment of 328ft twisted pair cabling; this is often insufficient and too costly in multi-
story buildings. Fortunately, the Enable-IT 820P Pro Series Extended Ethernet can
push the reach of Ethernet to almost 3 times the typical Ethernet distance.
A simple design methodology would be to think of the 820P Pro extending a standard
Ethernet line with power (PoE) up to 800ft (244m) and can also include 2 voice lines
simultaneously.
To increase the durability and extended use of the product providing maximum future
technology protection, 820P Pro Extended Ethernet Unit meets the challenge of modern
switched LANs and allows you to add features and capacity as your network expands.
The 820P Pro LRE kit includes a high powered PoE switch kit and the 820P Pro unit itself.
Unit Model Wiring Data Rate Max. Distance
820P Pro (4) pair CAT 2 up to CAT5e 15MB FD 800ft / (244m)

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 6 of 14

Key Benefits
The following list identifies the 820P Pro IP PoE Camera Extender Kit key benefits.
Dramatic cost reduction over any competing technology.
The Enable-IT 820P Pro IP PoE Camera Extender Kit requires no firmware and
no maintenance
Broadband technology that delivers in-building Ethernet access over 4 pair of
existing Category 2, up to Category 5e, 6 or 7, wiring up to 800ft (244m), whether
spare or actively in use for analog or digital voice. This means no new wiring is
required.
Provides one scalable infrastructure for Internet access, dual POTS, VoIP, video,
Power over Ethernet (PoE) and virtual private networking.
Rapid installation with small box profile; no programming and no firmware to
upgrade.
Low profile box with PoE and Ethernet data all in a single RJ-45 Ethernet jack.
Summary Of Features

The Enable-IT 820P Pro IP PoE Camera Extender Kit has the following hardware
features:
 Extended Ethernet and PoE over existing CAT2 up to CAT5e / CAT7 wiring
Rapid Telco style installation – no programming required
Supports digital VoD channels
Drives Ethernet 15 Mbps full-duplex service delivery up to 800ft (244m)
Network Equipment independence – Transparent to protocols/applications/MAC
Maintains lifeline POTS
802.3af Standard & Cisco PoE (Power over Ethernet) support – active/pass through
Specifications: Functionality:
PoE powered unit Data Rates 15Mbps Full Duplex
Passive Device, No Firmware. Ethernet modes supported
10Mbps half-duplex
820P Pro Dimensions: 10Mbps full duplex
Height: 1" (25mm) Max Distance 244m / 800ft
Depth: 3.25" (82.6mm) PoE compatible – active/pass through
Width: 4.4” (111.7mm)
Interfaces: Environment:
(1) RJ-45 10Mbs LAN input/output w PoE Operating temp: -49°F to 168°F (-45°to 76°C)
(1) RJ-45 Transport Interlink port Humidity 5% to 90%, non-condensing
(1) Optional 5v DC Power adapter input – not required for 820P Pro that is PoE Powered

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 7 of 14

Typical Use Applications
Enable-IT 820P Pro IP PoE Camera Extender Kit are usually installed onto telephone
wiring infrastructures where extension of backbone services is required and expensive
fiber options are prohibitive. The 820P Pro Extended Ethernet Kit allows a standard
Ethernet segment to be deployed quickly over existing 4 pair Telco Copper Wiring in
combination with existing POTS voice signals. That is 572ft beyond standard Category
rated Ethernet. There are no moving parts and no firmware to upgrade, thus providing
maintenance free operation.
Installers have the convenience of a 10Mbps LAN Ethernet unit for peace of mind
connectivity, low power and no maintenance. Rapid installation allows for minimal
interruption and the Broadband technology allows for investment protection up to 10 years
with no firmware or replacement issues. Bandwidth can be scaled according to the
Broadband Access Provider needs. The 820P Pro IP PoE Camera Extender Kit is a
passive device so interruption of Internet service does not affect POTS services. Carriers
and Access Providers can came and go, but the 820P Pro Extended Ethernet Unit
technologies continue to provide lasting value such as the other utilities like Water, gas
and electricity.
The Enable-IT 820P Pro IP PoE Camera Extender Kit is suited for the following key
environments:
 Commercial Buildings (Multi-Tenant Units)
 Business Parks (Multi-Tenant Units)
 Apartments (Multi-Residential Units)
 Hotels (Multi-Hospitality Units)
 Business Suites (Multi-Hospitality Units)
 School Campuses (University, K-12)
 College Housing (Multi-Residential Units)
 Mining Operations – Quarries, Mine Shafts
 Nautical Infrastructure – Cruise Ships, Marinas, Dive Operations, Submarines
 Video Surveillance/Security
 WiFi Deployment – ISP’s, RV Parks, Construction Sites
 Manufacturing – Foundries, Pharmaceutical, Aerospace, Automotive,
Petroleum, Concrete Plants, etc.
 Retail POS – Department stores, Bars, restaurants, retail spaces
 Government – Naval ships, FEMA, Housing, USGS, National Parks, Forestry,
Research Stations, NASA, Utilities, etc.
 Education – Outdoor Camps, College & University Campuses
 Healthcare – Hospitals, Elder Care, Outpatient Facilities
 Entertainment – Movie theaters, Home Entertainment, Fairs, Outdoor Venues

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 8 of 14

INSTALLING THE 820P PRO ETHERNET EXTENDER KIT
The Enable-IT 820P Pro IP PoE Camera Extender Kit has a distance restriction of 800ft
(244m) over existing Category 2, up to Category 5e, 6 or 7, wiring from device extension
to device extension. Therefore quick, simple site surveys and installation planning are
highly recommended.
This chapter describes the recommended installation process for the Enable-IT 820P Pro
Ethernet Extender Kit. The following topics are covered:
Site Plan – Installation Design Considerations
Unpacking the Enable-IT 820P Pro IP PoE Camera Extender Kit
Perform an Out Of The Box Test (OOTBT)
Performing the On-Site Installation
Site Plan – Installation Design Considerations
Total recommended distance of 1,100ft wiring from the 362 PoE Injector to the
LAN device on the remote end. – 328ft from LAN to 362, 328ft from 362 to 820P
Pro and 800ft from the 820P Pro to your end device is allowed.
Max distance then is 1,456ft (443m)
4 Pair Telco wiring for the Enable-IT 820P Pro Extended Ethernet Unit.
Wire pair used must be straight through, no taps/connection points.
Twisted Pair cabling delivers the best performance over distance.
Transparent to single line 802.3af PoE or 802.3at PoE Plus devices.
Option 1 – Single line PoE LAN Extension up to 800ft / 244m
We highly recommend a quick test to ensure the working order of your 820P Pro
kit.
 Apply power to the 362 PoE Injector kit. Cable the power cord to the 362 power
brick adapter and use it’s DIN DC female connector to attach to the DC jack on the
back of the 362 Injector module.
 Attach a RJ-45 LAN patch cord from your local LAN source to the Data N1 port
on the injector. Then run another LAN patch cord from the PoE&Data N2 port to the
LAN & PoE IN port on the 820P Pro unit.
 Lastly, use a third LAN patch cord to attach your end PoE LAN device. The 820P
Pro unit and your PoE LAN device should now be powered up and running.

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 9 of 14

Network Configuration
In some instances, your Ethernet switch, desktop computer, laptop, WiFi Access Point, or
any LAN device not mentioned may need to be configured for 10Mbps auto-sensing as
the 820P Pro is a 10Mbps Ethernet switch. It may be the case that your Ethernet switch
is not passing data through the 820 Pro to your remote LAN device, therefore setting the
LAN configuration on your device to 10Mbps will allow it to recognize the 820P Pro switch
settings.
Option 2 – PoE LAN Extension up to 1,600ft using an additional 820P Pro device
daisy-chained with the original.
 Apply power to the 362 PoE Injector kit. Cable the power cord to the 362 power
brick adapter and use it’s DIN DC female connector to attach to the DC jack on the
back of the 362 Injector module.
 Attach a RJ-45 LAN patch cord from your local LAN source to the Data N1 port
on the injector. Then run another LAN patch cord from the PoE&Data N2 port to the
LAN & PoE IN port on the 820P Pro unit.
 Now you may daisy chain the 2
nd
820P Pro unit by connecting a patch cord from
the Interlink Out port on your 1st 820P to the LAN & PoE IN port on the 2
nd
820P Pro
unit. Next, attach a PoE LAN device to the Interlink Out port on the 2
nd
820P Pro
unit. The 820P Pro units as well as your remote PoE device should now be powered
up and running.
LED indicators will provide visual operational status of the 820P Pro units.
820P Pro LAN & PoE IN – Slow yellow LED flashing indicates LAN connectivity.
Flickering yellow LED indicates LAN traffic.
820P Pro Interlink Out – Solid green LED indicates PoE power.
DIP Switch Settings: DIP switches 1 – 4:
Down (ON) - Enable PoE pass-through
UP (OFF) – Disable PoE pass-through
Default DIP Settings: DIP switches 1 – 4:
Down (ON) PoE Enabled for Data / PoE use
For installation at your desired location, keep in mind the following:
The backbone cable between the CO and your end device – RJ-45 Interlink port uses all
4-pairs of wiring for data and PoE (1, 2, 3 & 6 for data and 4, 5, 7 & 8 for PoE).

All Rights Reserved 1997 - 2013 Enable-IT, Inc. Page 10 of 14

DO NOT INSERT ANY BLANK RJ-45 HEADS INTO ANY
PORTS BEFORE CRIMPING – OTHERWISE YOU WILL
RENDER THE PORT USELESS – BENT PINS
Attach RJ-45 Male heads to your existing wiring and follow
the diagram below. For data only use pins 1,2,3 & 6. For
Data and PoE use all pins. PoE uses pins 4,5,7 & 8
Unpacking The Enable-IT 820P Pro IP PoE Camera Extender Kit
Carefully remove the Enable-IT 820P Pro Kit’s packing materials from the box. Verify that
the items listed below are present. Make sure that the equipment supplied matches what
you ordered. If any items are missing or damaged, please contact Enable-IT or your
distributor for assistance.
(1) Enable-IT 820P Pro IP PoE Camera Extender Unit
(1) Enable-IT 362 PoE Injector kit 60W – 56V
(2) LAN Ethernet Patch Cords
(1) Enable-IT 820P Pro Quickstart Guide
Performing The On-Site Installation
After removing the Enable-IT 820P Pro IP PoE Camera Extender Kit from the box all that
remains to install the unit on-site is to mount the unit, add RJ-45 Male heads to your wiring,
connect the wiring, cross connect voice lines if needed and attach end device Ethernet
patch cord cabling.
 Mounting the Enable-IT 820P Pro IP PoE Camera Extender Kit
The Enable-IT 820P Pro Extended Ethernet Units are designed for quick wall
mounting. Choose a location to mount each of the Enable-IT 820’s where the
maximum distance does not exceed 800ft (244m) total between devices to be
connected.
When wall-mounting the units it is recommended that you use the appropriate screw
anchors for your mounting surface. If mounting on existing plywood use wood screws;
if mounting onto drywall or sheetrock, use plastic drywall anchors to secure your
installation.
 Attaching cabling and devices to the Enable-IT 820P Pro IP PoE Camera Extender.
Apply power to the 362 PoE Injector kit. Cable the power cord to the 362 power brick
adapter and use it’s DIN DC female connector to attach to the DC jack on the back of
the 362 Injector module.
Attach a RJ-45 LAN patch cord from your local LAN source to the Data N1 port on the
injector. Then run another LAN patch cord from the PoE&Data N2 port to the LAN &
PoE IN port on the 820P Pro unit.
 Building the backbone between the 820P Pro unit and your remote LAN.
Crimp RJ-45 LAN heads onto your selected 4-pair wiring and insert into the
Interlink port on the 820P Pro unit and the other end to your LAN.