Enabling Devices 7511 User manual

6. Activate this toy by connecting any capability switch to the unit via the
1/8" jack, located on the side of the unit. If you need to use a ¼ " to 1/8"
adapter for your switch, it must be a mono adapter, not stereo.
7. Make sure that the connections between the external capability switch
and the adapter (if applicable) and the jack on the Magical Light Show
are tight. There should be no gaps.
8. Begin play by activating the external capability switch. The 6" spinning
art show has 36 different colored patterns. As the colored lights
change against a black background you hear upbeat music.
9. The Magical Light Show will continue playing while the external
capability switch continues to be activated. Once you release, all will
stop.
Troubleshooting:
Problem: The Magical Light Show does not work.
Action #1: Check or replace the AA batteries with fresh new batteries.
Action #2: Try a different switch that you know works with other
toys/devices to rule out the Magical Light Show as the source of the problem.
Care of Unit:
The Magical Light Show can be wiped clean with any household multi-
purpose cleaner and disinfectant.
Do not submerge the unit, as it will damage the contents and the electrical
components.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-TEC-TOYS or 1-800-832-8697
[email protected]
Magical Light Show with Mounting Arm -
#7511
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. [phone] / Fax [phone]
Toll Free 800.832.8697
www.enablingdevices.com

Our Most Popular Toys Now Available On Mounts!
For the child who needs special visual placement, we’ve selected four of our
most popular adapted toys and created a system that allows you to easily
mount them on a wheelchair, tabletop, bedrail or tray. Purchase any of the
four mountable toys with or without the mounting arm or purchase all four
toys with one mount. Size: 3 ½ "W x 10"D. Requires 6 AA Batteries.
Mounting arm is adjustable up to 24".
1. The Magical Light Show requires 6 AA batteries (Not included).
Alkaline batteries are recommended because they last longer. Do not use
rechargeable batteries because they supply lower voltage and the unit
may not perform as well.
2. The battery compartments are located on the back of the unit. To remove
the battery compartment covers, unscrew the small Phillips Head screws
then slide the covers off. Install new batteries, being careful to observe
proper (+) & (-) battery polarity. Replace covers and screw.
3. Clamping Options: Our mounting clamp is designed for mounting to
tubular (wheelchair, bedrail, walker, etc.) or flat surfaces such as a table
top or desk. For flat surface mounting use the included wedge insert shoe
stored in front of the locking knob on the clamp (see Fig.1) Loosen
locking knob slightly to remove wedge, tighten knob once wedge has
been removed.
Fig.1
4. At this point we recommend you place your mounting arm without the
Magical Light Show and do a rough setup, you can fine tune your
adjustments after you have placed the Magical Light Show on the arm.
Do not force or try adjusting the arm without first loosening the set
knobs for that portion of the arm. Each section of the arm has a set knob.
Once you have the arm in the desired position you can tighten the knobs
to lock the arm in place.
5. Once the arm is in position you can now place your Magical Light Show
on the arm. First back off the set knob on the Magical Light Show until it
is flush with the inside of the opening. This is necessary to allow the
holder to be pushed all the way down on the mounting arm post. The
post at the end of the arm also has a flat spot, which needs to be lined up
with the set screw on the Magical Light Show’s base. Once this is done
you can tighten the set knob to lock the holder to the arm. Please Note:
Make sure to back the set screw enough to allow the holder to be pushed
all the way down on the post of the arm, failure to do so will cause the
Magical Light Show to fall off the mounting arm and a fall could cause
damage to your Magical Light Show. (See Fig. 2).
Fig. 2
Rev 7/18/11
Tighten Set
Knob