Enclume LR2T User manual

Enclum e SLING RACK w/Tools
LR2T
Enclume hearth racks are the ultimate in
quality, design, strength and function.
Congratulations for owning one of the finest
storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
EFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished to resist corrosion and let the natural
beauty of the grey carbon steel shine through. Cleaning is easily done with a damp
cloth. Dry thoroughly after cleaning. If your rack is used outdoors, protect from
weather by covering or moving to a dry area when not in use. If a touch-up is ever
needed we recommend a "Pledge" like wax product.
Enclosed you will find everything needed for the assembly
and use of your hearth rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – Hard Glides
4 – 3/8" x 5/8" Button head screws
2 – 3/8" x ¾" Button head screws
1 – 7/32" Hex Key
Components included:
2 – Upright Legs
2 – Slings
1 – Tool Bar
2 – Feet
1 – Broom
1 – Poker
1 – Shovel
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] Fax [phone]
www.enclume.com
Limited Warranty: This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.

ASSEMBLY AND INSTALLATION INSTRUCTIONS for LR2T
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – Hard Glides
4 – 3/8" x 5/8" Button head
2 – 3/8" x ¾" Button head screws
1 – 7/32" Hex Key
Components included:
2 – Upright Legs
2 – Slings
1 – Tool Bar
2 – Feet
1 – Broom
1 – Poker
1 – Shovel
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Rack Assembly
1) Slip the floor glides over the ends of the legs
2) Position the two upright legs pieces over the legs so they form a square. Attach the pieces together using the four 3/8" x 5/8"
button head screws. The screws should be inserted from the top, tighten screws finger tight only at this point.
3) Remove the button head screw from one side of each upright holding the sling (also known as the kindling holder). Discard the
screws. Loosen, but do not remove the screws on the opposite side.
4) Attach the tool holder to the outside of the uprights using the 3/8" x ¾" screws. Screws need to be installed from the outside
through the tool holder, through the upright, and into the sling / kindling holder. Repeat process for the other upright.
5) Square up rack and tighten ALL screws at this time.
6) Hang tools on tool holder hooks
All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
It is important that your rack is assembled correctly. If the unit is assembled or used
incorrectly, it could become unstable and collapse, possibly causing injury.
Natural broom straw is flammable. Keep the broom well away from open flame. It should not
be used to sweep hot coals or ash.
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] Fax [phone]
www.enclume.com
WARNING