Enclume LR12B User manual

Enclume Fire Center Rack
LR12B
Enclume racks are the ultimate in
Quality, design, strength and function.
Congratulations for owning one of the finest
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x 5/8” Button head screws
4 – 3/8 x ½” Button head screws
1 – 7/32” Allen wrench
4 – Soft floor glides
Components included:
2 – Arched uprights
2 – Kindling holders
2 – Rectangular newspaper holders
1 – Newspaper support bar
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
If you need help, please call 1-877-ENCLUME
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com

ASSEMBLY AND INSTALLATION INSTRUCTIONS for LR12B
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x 5/8” Button head screws
4 – 3/8” x ½” Button head screws
1 – 7/32” Allen wrench
4 – Soft floor glides
Components included:
2 – Arched uprights
2 – Kindling holders
2 – Rectangular newspaper holders
1 – Newspaper support bar
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Rack Assembly
1) Slip the soft plastic floor glides over the ends of the arched uprights.
2) Position each rectangular newspaper holder so the threaded hole in the center of one long side is on the bottom, next to the
floor. Using the Allen wrench and the four 3/8” x 5/8” button head screws, attach the holders inside the arched uprights.
3) Attach the newspaper support bar to the inside of the newspaper holder with two of the 3/8” x ½” button head screws. The
screws should be inserted from the interior of the rack toward the floor. The bar should span the bottom of the newspaper
holder.
4) Attach the kindling holders the arched uprights with the two remaining 3/8” x ½” button head screws.
5) Square up the rack and tighten all the screws.
6) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack.
Cleaning is easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a
"Pledge" like wax product.
It is important that your rack is assembled correctly. If the unit is assembled or used incorrectly, it
could become unstable and collapse, possibly causing injury.
WARNING
Enclume Design Products, Inc.
24 Colwell Street, Port Hadlock, WA. 98339
Phone [phone] •Fax [phone]
www.enclume.com