Enclume PR15 User manual

Enclume WALL DOME
PR15
Enclume racks are the ultimate in
Quality, design, strength and function.
Congratulations for owning one of the finest
Storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
3 –3/8” x ½” Button Head Screw
2 – 2” Lag Screw
2 – D-Ring Screws
2 – Toggler® Wall Fasteners
1 – 7/32” Allen Wrench
2 - 1 ½" Wood Screws
Components included:
1 – Half Round Base
3 – Arms
1 – Back Bar
1 – D-ring Axial
6 – Angled Pot Hooks
6 – Straight Pot Hooks
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
::
potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com
::potracks.com
powered by ::kitchensource.com

ASSEMBLY AND INSTALLATION INSTRUCTIONS for PR15
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
3 – 3/8” x ½” Button Head Screw
2 – 2” Lag Screw
2 – D-Ring Screws
2 – Toggler® Wall Fasteners
1 – 7/32” Allen Wrench
2 - 1 ½" Wood Screws
Components included:
1 – Half Round Base
3 – Arms
1 – Back Bar
1 – D-ring Axial
6 – Angled Pot Hooks
6 – Straight Pot Hooks
ASSEMBLY AND INSTALLATION INSTRUCTIONS
Rack Assembly
1) If your rack is plated it is best to keep the tissue on during installation to avoid fingerprinting.
2) Thread the D-ring through the roll at the top if each of the three arms.
3) Fasten the arms to the outside of the half round base with the three button head screws. Tighten the screws.
4) Hold the rack up to the wall, carefully measure and mark the wall. The base must go into the solid wood of wall studs or into a
wooden wall. The D-ring attachment can be made with wall fasteners if a wooden support is unavailable.
5) Position the back bar on the inside of the half round base with the central curve outward, away from the wall. Thread the lag
screws through the back bar and the base and attach to the wall.
6) Attach the D-ring with the wall fasteners or screws as appropriate. Here is how to use the wall fastener:
How to use the TOGGLER® Brand TB® Drywall/Plasterboard Anchors
1. Fold anchor.
2. Insert anchor in 5/16” (8mm) hole and tap flush with wall
3. Insert setting key and pop anchor open (except in thick wall or solid
walls). Do not force or hammer key. Remove key.
4. Place item over anchor.
5. Insert screw and tighten until flush with item, then stop. Toggler hollow
wall anchors wedge solidly in thick and solid walls.
Patented under one or more of the following US patent numbers: 4.993.901; 5.028.186; and foreign
counterparts thereof. Other patents pending. Toggler and typeface, TB, anchor shape and symbol are
registered trademarks of MPC.
7) Your local hardware store can advise you if special hardware is needed for your particular kitchen.
8) The 4 straight pot hooks are to be used on the back bar.
9) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
10) The care and cleaning of our copper and brass units must be done with a low abrasive cleaner such as “Flitz”. Chrome racks are
best cleaned with a good quality glass cleaner like “Windex”. Our high quality plating will age & tarnish the same as solid
material. A periodic cleaning will restore your rack to its original brilliance
It is important that your rack is assembled correctly. If the unit is assembled or used incorrectly, it
could become unstable and collapse, possibly causing injury.
WARNING
::
potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com
::potracks.com
powered by ::kitchensource.com