HUANUO HNKB03 User manual

Thank you for choosing this HUANUO product! At HUANUO we
strive to provide you with the best quality products and services in
the industry. Please share your experience of our product with
others at www.huanuoav.com/reviews if you are satisfied. Should
you have any issues, please don't hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com
Model: HNKB03
Keyboard & Mouse Tray
Instruction Manual
V4.0

04
IMPORTANT SAFETY INFORMATION
Please carefully read all manual before use the product. If you do not understand the
manual or have any concerns or questions about the safety of the use, please contact
our Technical Support line at 1-800-556-0533 or customer service at
[email protected].
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our Techni-
cal Support line at 1-800-556-0533 or customer service at [email protected].
Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
CAUTION: Avoid potential personal injuries and property damage!
Supplied Parts and Hardware
Tools Needed (Not lncluded)
Step 1
[A] x6
Screw
M5x15mm
[B] x6
Washer
15x5.3x1.2mm
[C] x4
Bolt
M5x12mm
[D] x6
Screw
M5x20mm
Pencil Drill 5/64in. (2mm)
Wood Drill
Phillips
Screwdriver
x1
Keyboard Tray Support
01
x1
Keyboard Tray
02
x1
Template
04
x1
Wrist Cushion
03
Position the template [04]
to the bottom of the
desktop and mark 6 pilot
holes.
- 1 -

01
01
Step 2 Install the Keyboard Tray Support [01] to the Bottom of Desktop
Step 3 Secure Keyboard Tray [02] to Keyboard Tray Support [01]
ø5/64 in. (2mm)
25/32 in. (20mm)
ø5/64 in. (2mm)
19/32 in. (15mm)
2-1
Phillips
Screwdriver
(Not Included)
Tighten
Loosen
①. Slightly loosen the pre-assembled
spanner [S], then lift and rotate the
part [01A] to the angle as shown in
fig a.
②. Retighten the pre-assembled
spanner [S]
③. Continue to rotate
the part [01A] and
slightly push it backward
as shown in the fig b.
Install the keyboard tray support
[01] under the table with screws
[A or D] and washers [B], then
tighten the screws.
HEAVY! You may need
assistance with this step.
Phillips Screwdriver
(Not Included)
- 2 -
B
C
A/D
Select [A or D] screws according
to the thickness of the desktop. If
it is difficult to install the screws
[A/D], you can drill the pilot holes
using electric driver.
SFig a.
Fig b.
03
02
01A
01B
01A
01A
2-2
Electric Driver
(Not Included)
Screw A Screw D

Step 4 Adjust the Keyboard Tray
Telescopic Adjustment
If needed, the height can be adjusted.
1. Loosen the pre-assembled
spanner [S].
2. Adjust the keyboard tray to
desired height.
3. Secure the spanner [S] to fix
the keyboard in place
Loosen
Tighten
- 3 -
Swivel and Tilt Adjustment
Height Adjustment