Endress+Hauser Deltabar PMD55B User manual

Products Solutions Services
Operating Instructions
Deltabar PMD55B
Differential pressure measurement
PROFINET with Ethernet-APL
advanced physical layer
BA02230P/00/EN/02.23-00
71605808
2023-02-22
Valid as of version
01.00.zz (Device firmware)

Deltabar PMD55B PROFINET with Ethernet-APL
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device
• Avoid danger to individuals or the facility: read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures
The manufacturer reserves the right to modify technical data without prior notice. The
Endress+Hauser sales organization will supply you with current information and updates
to these instructions.

Deltabar PMD55B PROFINET with Ethernet-APL Table of contents
Endress+Hauser 3
Table of contents
1 About this document ............... 5
1.1 Document function ..................... 5
1.2 Symbols ............................. 5
1.3 List of abbreviations ..................... 7
1.4 Documentation ........................ 7
1.5 Registered trademarks ................... 7
2 Basic safety instructions ............ 8
2.1 Requirements for the personnel ............ 8
2.2 Intended use .......................... 8
2.3 Workplace safety ....................... 8
2.4 Operational safety ...................... 8
2.5 Product safety ......................... 9
2.6 IT security ............................ 9
2.7 Device-specific IT security ................ 9
3 Product description ............... 11
3.1 Product design ....................... 11
4 Incoming acceptance and product
identification ..................... 12
4.1 Incoming acceptance ................... 12
4.2 Product identification ................... 12
4.3 Storage and transport .................. 13
5 Mounting ......................... 14
5.1 Mounting requirements ................. 14
5.2 Mounting the device ................... 16
5.3 Post-mounting check ................... 24
6 Electrical connection .............. 25
6.1 Connecting requirements ............... 25
6.2 Connecting the device .................. 25
6.3 Ensuring the degree of protection ......... 28
6.4 Post-connection check .................. 29
7 Operation options ................. 30
7.1 Overview of operation options ............ 30
7.2 Operating keys and DIP switches on the
electronic insert ....................... 30
7.3 Structure and function of the operating
menu .............................. 30
7.4 local display ......................... 30
7.5 Access to operating menu via web browser ... 32
7.6 Access to the operating menu via the
operating tool ........................ 36
8 System integration ................ 38
8.1 Overview of device description files ......... 38
8.2 Device master file (GSD) ................. 38
8.3 Cyclic data transmission ................ 40
8.4 System redundancy S2 .................. 42
9 Commissioning ................... 43
9.1 Preliminaries ........................ 43
9.2 Function check ....................... 43
9.3 Establishing a connection via FieldCare and
DeviceCare .......................... 43
9.4 Hardware settings ..................... 44
9.5 Configuring the communication parameters
via the software ...................... 44
9.6 Setting the operating language ........... 45
9.7 Configuring the device ................. 45
9.8 "Simulation" submenu ................... 53
9.9 Protecting settings from unauthorized
access .............................. 54
10 Operation ......................... 56
10.1 Reading off the device locking status ....... 56
10.2 Reading off measured values ............. 56
10.3 Adapting the device to process conditions .... 56
11 Diagnostics and troubleshooting ... 58
11.1 General troubleshooting ................. 58
11.2 Diagnostics information via LED ........... 60
11.3 Diagnostic information on local display ...... 61
11.4 Diagnostic information in the Web browser .. 61
11.5 Diagnostic list ........................ 62
11.6 Diagnostic list ........................ 64
11.7 Event logbook ........................ 67
11.8 Resetting the device .................... 69
11.9 Firmware history ...................... 70
12 Maintenance ...................... 72
12.1 Maintenance work ..................... 72
13 Repair ............................ 73
13.1 General information ................... 73
13.2 Spare parts .......................... 73
13.3 Return .............................. 74
13.4 Disposal ............................ 74
14 Accessories ....................... 75
14.1 Device-specific accessories ............... 75
14.2 Device Viewer ........................ 75
15 Technical data .................... 76
15.1 Output ............................. 76
15.2 Environment ......................... 78
15.3 Process ............................. 81

Table of contents Deltabar PMD55B PROFINET with Ethernet-APL
4 Endress+Hauser
Index .................................. 85

Deltabar PMD55B PROFINET with Ethernet-APL About this document
Endress+Hauser 5
1 About this document
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols
1.2.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Ground connection:
Terminal for connection to the grounding system.
1.2.3 Symbols for certain types of information
Permitted:
Procedures, processes or actions that are permitted.
Forbidden:
Procedures, processes or actions that are forbidden.

About this document Deltabar PMD55B PROFINET with Ethernet-APL
6 Endress+Hauser
Additional information:
Reference to documentation:
Reference to page:
Series of steps:
1.
,
2.
,
3.
Result of an individual step:
1.2.4 Symbols in graphics
Item numbers: 1, 2, 3 ...
Series of steps:
1.
,
2.
,
3.
Views: A, B, C, ...
1.2.5 Symbols on the device
Safety instructions:
Observe the safety instructions contained in the associated Operating Instructions.

Deltabar PMD55B PROFINET with Ethernet-APL About this document
Endress+Hauser 7
1.3 List of abbreviations
URL OPLMWP
LRL
0
p
LRV URV
1
2
3
4
A0029505
1 OPL: The OPL (overpressure limit = measuring cell overload limit) for the device depends on the lowest-rated
element, with regard to pressure, of the selected components, i.e. the process connection has to be taken into
consideration in addition to the measuring cell. Pay attention to the pressure/temperature dependency.
2 The MWP (maximum working pressure) for the measuring cells depends on the lowest-rated element, with
regard to pressure, of the selected components, i.e. the process connection has to be taken into consideration
in addition to the measuring cell. Pay attention to the pressure/temperature dependency. The MWP may be
applied at the device for an unlimited period of time. The MWP can be found on the nameplate.
3 The maximum measuring range corresponds to the span between the LRL and URL. This measuring range is
equivalent to the maximum calibratable/adjustable span.
4 The calibrated/adjusted span corresponds to the span between the LRV and URV. Factory setting: 0 to URL.
Other calibrated spans can be ordered as customized spans.
p Pressure
LRL Lower range limit
URL Upper range limit
LRV Lower range value
URV Upper range value
TD Turn down. Example - see the following section.
1.4 Documentation
All available documents can be downloaded using:
• the serial number of the device (see cover page for description) or
• the data matrix code of the device (see cover page for description) or
• the "Downloads" area of the website www.endress.com
1.4.1 Supplementary device-dependent documentation
Additional documents are supplied depending on the device version ordered: Always
comply strictly with the instructions in the supplementary documentation. The
supplementary documentation is an integral part of the device documentation.
1.5 Registered trademarks
PROFINET®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany

Basic safety instructions Deltabar PMD55B PROFINET with Ethernet-APL
8 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well as
in the certificates (depending on the application)
‣Follow instructions and comply with conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the
facility's owner-operator
‣Following the instructions in these Operating Instructions
2.2 Intended use
The Deltabar is a differential pressure transmitter for measuring pressure, flow, level and
differential pressure.
2.2.1 Incorrect use
The manufacturer is not liable for damage caused by improper or non-intended use.
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability.
2.3 Workplace safety
When working on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
‣Switch off the supply voltage before connecting the device.
2.4 Operational safety
Risk of injury!
‣Operate the device only if it is in proper technical condition, free from errors and faults.
‣The operator is responsible for the interference-free operation of the device.
Modifications to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers:
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability:
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to the repair of an electrical device.

Deltabar PMD55B PROFINET with Ethernet-APL Basic safety instructions
Endress+Hauser 9
‣Use original spare parts and accessories from Endress+Hauser only.
Hazardous area
To eliminate the risk of danger to persons or the facility when the device is used in the
approval-related area (e.g. explosion protection, pressure equipment safety):
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area.
‣Observe the specifications in the separate supplementary documentation that is an
integral part of these Instructions.
2.5 Product safety
This device is designed in accordance with good engineering practice to meet state-of-the-
art safety requirements, has been tested, and left the factory in a condition in which it is
safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.
2.6 IT security
Endress+Hauser can only provide a warranty if the device is installed and used as
described in the Operating Instructions. The device is equipped with security mechanisms
to protect it against any inadvertent changes to the device settings. IT security measures in
line with operators' security standards and designed to provide additional protection for
the device and device data transfer must be implemented by the operators themselves.
2.7 Device-specific IT security
The device offers specific functions to support protective measures by the operator. These
functions can be configured by the user and guarantee greater in-operation safety if used
correctly. An overview of the most important functions is provided in the following section:
• Write protection via hardware write protection switch
• Access code to change the user role (applies for operation via Bluetooth, FieldCare,
DeviceCare, Asset Management Tools (e.g. AMS, PDM and web server)
Function/interface Factory setting Recommendation
Access code
(also applies for web server login or
FieldCare connection)
Not enabled
(0000)
Assign a customized access code during
commissioning.
Web server Enabled On an individual basis following risk assessment.
Service interface (CDI) Enabled On an individual basis following risk assessment.
Write protection via hardware write
protection switch
Not enabled On an individual basis following risk assessment.
2.7.1 Protecting access via a password
Different passwords are available to protect write access to the parameters of the device.
Protect write access to the parameters of the device via the local display, web browser or
operating tool (e.g. FieldCare, DeviceCare). Access authorization is clearly regulated
through the use of a user-specific access code.

Basic safety instructions Deltabar PMD55B PROFINET with Ethernet-APL
10 Endress+Hauser
User-specific access code
Write access to the parameters of the device via the local display, web browser or
operating tool (e.g. FieldCare, DeviceCare) can be protected using the editable, user-
specific access code.
When the device is delivered, the device does not have an access code and is equivalent to
0000 (open).
General notes on the use of passwords
• During commissioning, change the access code that was used when the device was
delivered from the factory
• When defining and managing the access code, comply with the general rules for the
generation of a secure password
• The user is responsible for managing the access code and for using the code with due
care
• If the password is lost, see the "Resetting the device" section
2.7.2 Access via web server
Due to the integrated web server, the device can be operated and configured via a web
browser and PROFINET with Ethernet-APL. In addition to the measured values, device
status information is also displayed, allowing users to monitor the status of the device.
Furthermore the device data can be managed and the network parameters can be
configured.
Access to the network is required for the PROFINET with Ethernet-APL connection.
Supported functions
Data exchange between the operating unit (such as a notebook for example) and the
measuring device:
• Export parameter settings (PDF file, create documentation of the measuring point
configuration)
• Export the Heartbeat Technology verification report (PDF file, only available with the
"Heartbeat Verification" application package)
• Download driver (GSDML) for system integration
The web server is enabled when the device is delivered. The web server can be disabled via
the Web server functionality parameter if necessary (e.g. after commissioning).
The device and status information can be hidden on the login page. This prevents
unauthorized access to the information.
Detailed information on the device parameters:
"Description of device parameters" document