Endress+Hauser Gammapilot M FMG60 User manual

BA329F/00/en/10.09
71104600
Valid as of software version:
V01.03.02
Operating Instructions
Gammapilot M FMG60
Radiometric Measurement
8

Brief operating instructions Gammapilot M FMG60 with PROFIBUS PA
2Endress+Hauser
Brief operating instructions
L00-FMG60xxx-05-00-00-en-050
Contents of the Operating Instructions
These Operating Instructions describe how to install and commission the radiometric compact
transmitter Gammapilot M (communication version PROFIBUS PA). All the functions that are
required for standard measuring tasks have been included. Also, the Gammapilot M provides
additional functions for optimizing the measuring point and for converting the measured value.
These functions are not included in these Operating Instructions.
You can find an overview of all the device functions in the Appendix.
A detailed description of all the instrument functions is given in Operating Instructions
BA287F "Gammapilot M - Description of Device Functions" which can be found on the CD-ROM
supplied.
E
+
-
+
E
+
-
-
… …
… …
100 (HART)
2457 (PA,FF)
333 (HART)
33333 (PA,FF)
…
… …
E
E
E
E
52025626
KA242F/00/a2/02.07
Gammapilot M - Quick Setup
*00
measured value
Group
selection
*0
basic setup
*2
safety settings
*C
system
parameters
*4
linearisation
*5
gammagraphy
*6
output (HART, FF)
profibus param.(PA)
*A
diagnostics *A0
present
error
*01
todays
date
*02
beam type *03 isotope *04 operating
mode
*06
density
unit
*09
pipe diam.
unit
*0A
pipe diam. *0B
output
damping
*A1
previous
error
*A4
unlock
parameter
*3
temp. compens.
*9
display *92 language
*A3
reset
*C0
tag
marking
*05
meas.
mode
slave, end slave
*1
calibration *10 backgr.
calib
start
*11
avg. pulse
rate
*12
bgr. pulse
rate
stop/edit
*13
calibr. point
*14
value
full
*16
full
calibr.
stop/edit
*15
calibration
start
*11
avg. pulse
rate
*19
next point
*17
value
empty
*18
empty
calibr.
stop/edit
*15
calibration
start
*11
avg. pulse
rate
density/concentration
no
yes
*1B
density
calibr.
stop/edit
start
*11
avg. pulse
rate
*1C
density
value
*1D
calibr.
point
*1E
absorp.
coeff.
*1F
ref. pulse
rate
*1A
calibr.
point
*15
calibration *19
next point
no
yes
Contrast: +or+
*indicates the
meas.mode:
L: Level
S: Level limit
D: Density
C: Concentration
*07
min.
density
*08
max.
density
level/
limit

Gammapilot M FMG60 with PROFIBUS PA Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 4
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Installation, commissioning, operation . . . . . . . . . . . 4
1.3 Hazardous area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Radiation protection . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Notes on safety conventions and icons . . . . . . . . . . . 8
2 Identification . . . . . . . . . . . . . . . . . . . . 9
2.1 Parts of the Gammapilot M . . . . . . . . . . . . . . . . . . . 9
2.2 Nameplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3 Ordering structure . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Supplied documentation . . . . . . . . . . . . . . . . . . . . 12
2.6 Certificates and approvals . . . . . . . . . . . . . . . . . . . 13
2.7 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 13
3 Installation . . . . . . . . . . . . . . . . . . . . . 14
3.1 Incoming acceptance, transport, storage . . . . . . . . . 14
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 15
3.3 Water cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 21
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 22
4.1 Terminal compartments . . . . . . . . . . . . . . . . . . . . . 22
4.2 Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3 Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . 23
4.4 Fieldbus connectors . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5 PROFIBUS PA cable specifications . . . . . . . . . . . 25
4.6 Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.7 Potential equalization . . . . . . . . . . . . . . . . . . . . . . 25
4.8 Wiring in terminal compartment A . . . . . . . . . . . . 26
4.9 Wiring in terminal compartment B . . . . . . . . . . . . . 27
4.10 Connecting the remote display and operation FHX40 .
28
4.11 Wiring in cascading mode . . . . . . . . . . . . . . . . . . . 29
4.12 Measuring solids flow . . . . . . . . . . . . . . . . . . . . . . 30
4.13 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 30
5 Operation . . . . . . . . . . . . . . . . . . . . . . 31
5.1 Overview over the operating options . . . . . . . . . . . 31
5.2 Display operation . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3 Alternative operation options . . . . . . . . . . . . . . . . . 36
5.4 Lock/unlock configuration . . . . . . . . . . . . . . . . . . 37
5.5 Reset to the default configuration . . . . . . . . . . . . . . 38
5.6 PROFIBUS PA interface . . . . . . . . . . . . . . . . . . . . . 38
6 Commissioning. . . . . . . . . . . . . . . . . . 50
6.1 Calibration: overview . . . . . . . . . . . . . . . . . . . . . 50
6.2 Switching on the device . . . . . . . . . . . . . . . . . . . . 55
6.3 Basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.4 Calibration for level measurement and limit detection
62
6.5 Calibration for density and concentration measurements
71
6.6 Density measurement/temperature-compensated . . 79
6.7 Gammagraphy detection . . . . . . . . . . . . . . . . . . . . 79
7 Maintenance and repairs . . . . . . . . . . . 80
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 80
7.2 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
7.3 Repairs to Ex-approved devices . . . . . . . . . . . . . . . 80
7.4 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
7.5 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7.6 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7.7 Contact addresses of Endress+Hauser . . . . . . . . . . . 81
8 Accessories . . . . . . . . . . . . . . . . . . . . . 82
8.1 Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . 82
8.2 ToF adapter FXA291 . . . . . . . . . . . . . . . . . . . . . . . 82
8.3 Proficard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
8.4 Profiboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
8.5 Remote display FHX40 . . . . . . . . . . . . . . . . . . . . . . 83
8.6 Mounting device FHG60 (for level measurement and
level limit measurement) . . . . . . . . . . . . . . . . . . . . 84
8.7 Clamping device for density measurement FHG61 . 86
8.8 Measurement section for density measurement FHG62
86
9 Troubleshooting . . . . . . . . . . . . . . . . . 87
9.1 System error messages . . . . . . . . . . . . . . . . . . . . . . 87
9.2 Possible calibration errors . . . . . . . . . . . . . . . . . . . . 90
9.3 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . 90
10 Technical data . . . . . . . . . . . . . . . . . . . 91
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 91
11 Appendix. . . . . . . . . . . . . . . . . . . . . . . 98
11.1 Operating menu for level measurements . . . . . . . . 98
11.2 Operating menu for level limit detection . . . . . . . 100
11.3 Operating menu for density and concentration
measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.4 Measuring principle . . . . . . . . . . . . . . . . . . . . . . . 104
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Safety instructions Gammapilot M FMG60 with PROFIBUS PA
4Endress+Hauser
1 Safety instructions
1.1 Designated use
The Gammapilot M is a compact transmitter for non-contact level, level limit, density and
concentration measurement. The measuring range of a single Gammapilot M extends up to 2 m.
Large measuring ranges of any size can be implemented, however, by cascading several
Gammapilot M devices.
1.2 Installation, commissioning, operation
The Gammapilot M is fail-safe and is constructed to the state-of-the-art. It meets the appropriate
standards and EC directives. However, if you use it improperly or other than for its designated use,
it may pose application-specific hazards, e.g. product overflow due to incorrect installation or
configuration. Installation, electrical connection, startup, operation and maintenance of the
measuring device must therefore be carried out exclusively by trained specialists authorized by the
system operator. Technical personnel must have read and understood these Operating Instructions
and must adhere to them. You may only undertake modifications or repair work to the device when
it is expressly permitted by the Operating Instructions.
1.3 Hazardous area
Measuring systems for use in hazardous environments are accompanied by separate "Ex
documentation", which is an integral part of these Operating Instructions. Strict compliance with
the installation instructions and ratings as stated in this supplementary documentation is mandatory.
• Ensure that all personnel are suitably qualified.
• Measuring point requirements with regard to measurement and safety must be observed.
#Warning!
Depending on the certificate version observe the associated Safety Instructions (→ä94).
#Warning!
The three screws, connecting the pipe housing
to the compartment housing, must not be
opened.
L00-FMG60xxx-05-00-00-xx-052

Gammapilot M FMG60 with PROFIBUS PA Safety instructions
Endress+Hauser 5
1.4 Radiation protection
The Gammapilot M is used in conjunction with a radioactive source, contained in a source
container. When handling radioactive sources, the following instructions have to be observed:
1.4.1 Basic regulations on radiation protection
#Warning!
When handling radioactive sources, all unnecessary radiation exposure should be avoided. All
unavoidable radiation exposure should be kept as low as possible. Three measures are used for this:
L00-QGxxxxxx-16-00-00-en-001
Distance
Keep as far away as possible from the radiation source. The local radiation intensity decreases as the
square-root of the distance from the radiation source.
Shielding
Ensure the best possible shielding between the radiation source and yourself as well as all other
individuals. Effective shielding is provided by source containers (FQG61, FQG62, QG2000) and all
high-density materials (lead, iron, concrete).
"Caution!
When working with source containers, all the instructions for mounting and usage outlined in the
following documents must be observed:
Time
Stay as short as possible in the area exposed to radiation.
Source Container Document
FQG61, FQG62 TI435F
QG2000 BA223F

Safety instructions Gammapilot M FMG60 with PROFIBUS PA
6Endress+Hauser
1.4.2 Legal requirements for radiation protection
Handling radioactive emitters is legally controlled. The radioactive protection regulations of the
country in which the plant is to be operated are to be strictly observed. In the Federal Republic of
Germany the current radiation protection requirements are applicable. The following points, in
particular, are important for radioactive measurement:
Handling permit
A handling permit is required for operating a plant which uses gamma radiation. Application for the
permit must be made to the state government (Land) or the authority responsible (State Offices for
Environmental Protection, Trade Inspection Offices, etc.). The Endress+Hauser sales organization
will be pleased to help you obtain the permit.
Radiation protection officer
The operator of the plant must nominate someone responsible for radiation protection who has the
necessary specialist knowledge and who is responsible for observing all radiation protection
regulations and procedures for radiation protection. Endress+Hauser offers training courses in
which the necessary specialist knowledge can be acquired.
Control zone
Only persons exposed to radiation during the course of their job may sojourn in control zones
(i.e. areas where the local dose rate exceeds a specific value) provided they are subjected to official
personnel dose monitoring procedures. For the Federal Republic of Germany the limit values for the
control zone are specified in the current radiation protection requirements.
The Endress+Hauser sales organization will be pleased to provide further information on radiation
protection and regulations in other countries.
1.4.3 Behavior in the event of an incident
Emergency measures
If the source container or the radiation source is damaged by accident or another unforeseen event
or if the radiation source is lost by other means, the following emergency measures shall be initiated
immediately:
• Inform the radiation protection officer immediately.
• All employees must leave the danger area immediately. The area around the measuring point
must be barred to access and labeled.
• Production must be halted immediately if there is a risk that the radioactive material has got into
the material being measured. Possibly contaminated material must be secured and may not be
further used before it has been tested.
• All persons involved in cleaning up (fire brigade, works security, etc.) must be informed of the
hazards of radiation.
Report to the responsible authority
As soon as the emergency measures have been initiated, the authorities responsible for radiation
must be informed by the radiation protection officer.

Gammapilot M FMG60 with PROFIBUS PA Safety instructions
Endress+Hauser 7
1.4.4 Procedures after termination of the application
Internal measures
As soon as a radiometric measuring device is no longer required, the radiation source on the source
container must be switched off. The source container shall be removed in accordance with all
relevant regulations and saved in a lockable room having no through traffic. The responsible
authorities shall be informed of these measures. The access to the storage room shall be measured
out and signed. The radiation protection officer is responsible for protecting against theft. The
radiation source in the source container must not be scrapped with the other parts of the plant. It
should be returned as quickly as possible.
Return
FR Germany
Contact your E+H sales center to organize the return of the radiation source for inspection with a
view to reuse or recycling by Endress+Hauser.
Other countries
Contact your E+H sales center or the appropriate authorities (government ministry) or regulating
authority to find a way of returning the radiation source nationally. If return is not possible
domestically, the further procedure must be agreed with the sales center concerned. The
destination airport for potential returns is Basle, Switzerland.
Conditions
The following conditions must be met before returning the material:
• An inspection certificate no more than three months old confirming the leak-tightness of the
radiation source must be in the possession of E+H (wipe test certificate).
• The serial number, type of radiation source (60Co or 137Cs), activity and model of radiation source
must be specified. This data may be found in the documents supplied with the radiation source.
• The material must be returned in an approved secondary containment suitable for simple handling
and in type-tested type-A packaging (IATA rules).
1.4.5 Using source containers
Strict compliance with the safety instructions and instructions on installing, mounting and operating
is mandatory.
For details, see
• TI264F/00 for FQG61 and FQG62
• TI346F/00 and BA223F/00 for QG2000

Safety instructions Gammapilot M FMG60 with PROFIBUS PA
8Endress+Hauser
1.5 Notes on safety conventions and icons
In order to highlight safety-relevant or alternative operating procedures in the manual, the following
conventions have been used, each indicated by a corresponding symbol in the margin.
Safety instructions
#Warning!
Indicates an action or procedure which, if not performed correctly, can result in serious personal injury,
a safety hazard or the destruction of the device.
"Caution!
Indicates an action or procedure which, if not performed correctly, can result in personal injury or the
incorrect operation of the device.
!Note!
Indicates an action or procedure which, if not performed correctly, can have an indirect effect on
operation or trigger an unexpected response on the part of the device.
Explosion protection
0Device certified for use in explosion hazardous area
If the device has this symbol embossed on its name plate it can be installed in an explosion hazardous
area
-Hazardous area
Symbol used in drawings to indicate explosion hazardous areas. Devices located in and wiring entering
areas with the designation “explosion hazardous areas” must conform with the stated type of
protection.
.Safe area (non-explosion hazardous area)
Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices located in
safe areas still require a certificate if their outputs run into explosion hazardous areas
Electrical symbols
%Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied
&Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be applied or
supplied
)Ground connection
A grounded terminal, which as far as the operator is concerned, is already grounded by means of an
earth grounding system
*Protective ground connection
A terminal which must be connected to ground prior to making any other connection to the equipment.
+Equipotential connection
A connection that has to be connected to the plant grounding system:
This may be a potential equalization line or a star grounding system depending on national or company
codes of practice.
Temperature resistance of the connecting cables
States that the connecting cables must be resistant to a temperature of at least 85 °C.
t >85°C

Gammapilot M FMG60 with PROFIBUS PA Identification
Endress+Hauser 9
2 Identification
2.1 Parts of the Gammapilot M
1. Terminal head
2. Mounting collar
3. Detector pipe
4. Terminal compartment A
5. Terminal compartment B
6. Centering knob
7. Instrument nameplate
8. Supplementary nameplate
9. Measuring range marks
10. Cooling water connections
11. PML connector of the water
cooling jacket
12. Marking of the radiation
window (only for versions
with collimator)
L00-FMG60xxx-03-00-00-xx-002
A: Gammapilot M without water cooling jacket
B: Gammapilot M with water cooling jacket
C: Gammapilot M with collimator
1
2
3
4
5
6
9
9
78
9
9
10
10
A B/C
11
12
C

Identification Gammapilot M FMG60 with PROFIBUS PA
10 Endress+Hauser
2.2 Nameplates
Example: approval nameplate for a FISCO field device
L00-FMG60xxx-18-00-00-xx-003
Device nameplate
L00-FMG60xxx-18-00-00-xx-001
1: Order code (as defined by the ordering structure);
2: Serial number; 3: Measuring range; 4: Power supply;
5: Output signal; 6: Max. ambient temperature
Supplementary nameplate (Examples)
L00-FMG60xxx-18-00-00-xx-002
7: No. of certificate; 8: Equipment group and category;
9: Type of protection; 10: Reference to additional safety-
relevant information; 11: Reference to additional
certificates (e.g. WHG); 12: Specification of required
temperature resistance of the connected cables (only for
device versions with water cooling jacket)
Order Code:
Ser.-No.:
IP 65/67
Gammapilot M
Made in Germany, D-79689 Maulburg
AMB
L= mm
Dat./Insp.:
250001828- -
NEMA 4/6 Type 4/6
T
-40°C °C
1
23
4
5
6
000000- -
KEMA 04 ATEX
11
10
7
89
12
000000- -
11
10
12
KEMA 04 ATEX 1153
II 2(1) GD EEx de [ia] IIC T6
IP67 T 80°C FISCO field device
Zone 1 [Zone 0]
XA303F-A
SDXXXX-X
Z-65.15.212
001829-B
IECEx BKI 05.0001
t >85°C

Gammapilot M FMG60 with PROFIBUS PA Identification
Endress+Hauser 11
2.3 Ordering structure
Versions that mutually exclude one another are not marked.
Ordering information Gammapilot M FMG60
Feature
10
Option
Approval
ANon-hazardous area
CNEPSI Ex de (ia) IIC T6
DNEPSI Ex d (ia) IIC T6
FNon-hazardous area, WHG (level limit)
GIECEx Zone 1 (Zone 0) Ex de (ia) IIC T6
HIECEx Zone 1 (Zone 0) Ex d (ia) IIC T6
KTIIS Ex d (ia) IIC T6
MATEX II 2 (1) GD EEx d (ia) IIC T6, WHG (level limit)
NCSA General Purpose
PCSA Cl.I Gr.A-D/Cl.II Gr.E-G/Cl.III
SFM Cl.I Gr.A-D/Cl.II Gr.E-G/Cl.III
1ATEX II 2 (1) G EEx de (ia) IIC T6
2ATEX II 2 (1) G EEx de (ia) IIC T6, WHG (level limit)
3ATEX II 2 (1) G EEx d (ia) IIC T6
4ATEX II 2 (1) G EEx d (ia) IIC T6, WHG (level limit)
5ATEX II 2 (1) D
6ATEX II 2 (1) GD EEx de (ia) IIC T6
7ATEX II 2 (1) GD EEx de (ia) IIC T6, WHG (level limit)
8ATEX II 2 (1) GD EEx d (ia) IIC T6
YSpecial version, to be specified
20 Power supply
190-253 VAC
218-36 VDC
9Special version, to be specified
30 Power supply wiring/output wiring
ANon-Ex; Non-Ex
BEEx e; EEx ia
CEEx e; EEx e
DEx d (XP); Ex d (XP)
EEx d (XP); Ex ia (IS)
FDust-Ex; Dust-Ex
GEEx e, Dust-Ex; EEx e, Dust-Ex
HEEx d, Dust-Ex; EEx d, Dust-Ex
JEEx e, Dust-Ex; EEx ia, Dust-Ex
KEEx d, Dust-Ex; EEx ia, Dust-Ex
LDust-Ex; Ex ia
YSpecial version, to be specified
40 Output
14-20 mA, HART
2PROFIBUS PA
3FOUNDATION Fieldbus
9Special version, to be specified
FMG60 - Product designation, first part

Identification Gammapilot M FMG60 with PROFIBUS PA
12 Endress+Hauser
2.4 Scope of delivery
• Ordered version of the device (including Operating Instructions)
• Endress+Hauser operating program (on the CD-ROM supplied)
• Accessories as ordered
2.5 Supplied documentation
2.5.1 Operating Instructions (BA 329F, this manual)
Describe how to install and commission the Gammapilot M (communication version
PROFIBUS PA). Those functions of the operating menu are included, which are required for
standard measuring tasks. Any additional functions are contained in the "Description of Device
Functions" (BA287F).
2.5.2 Description of Device Functions (BA287F, on CD-ROM)
Contains a detailed description of all the functions of the Gammapilot M and applies for all
communication versions. This document can be found as a PDF file on the CD-ROM supplied and
can be downloaded from the Internet under "www.de.endress.com" (→download).
50 Scintillator measuring range
ANaI-Crystal 50x50mm
CNaI-Crystal 50x50mm + collimator radial
DNaI-Crystal 50x50mm + water cooling
GPVT 200mm
HPVT 200mm + water cooling
JPVT 400mm
KPVT 400mm + water cooling
LPVT 800mm
MPVT 800mm + water cooling
NPVT 1200mm
PPVT 1200mm + water cooling
QPVT 1600mm
RPVT 1600mm + water cooling
SPVT 2000mm
TPVT 2000mm + water cooling
YSpecial version, to be specified
60 Housing, Pipe; Operation
1316L, 316L; Prepared for FHX40, remote display (accessory)
3Alu, 316L; prepared for FHX40, remote display (accessory)
9Special version, to be specified
70 Cable entry power supply
AGland M20
BThread M20
CThread G1/2
DThread NPT1/2
YSpecial version, to be specified
80 Cable entry output
1equal to supply (gland/thread)
2Plug M12
3Plug 7/8"
9Special version, to be specified
90 Additional option
ABasic version
BSIL2 declaration of conformity (max limit switch)
YSpecial version, to be specified
FMG60 - Product designation

Gammapilot M FMG60 with PROFIBUS PA Identification
Endress+Hauser 13
2.5.3 Safety instructions
Additional safety instructions (XA, ZE, ZD) are supplied with certified device versions. Refer to the
nameplate for the names of the safety instructions that apply to your device variant.
An overview of the certificates and approvals can be found in the "Technical data" chapter,
"Certificates and approvals" section.
2.6 Certificates and approvals
CE mark, declaration of conformity
The device is designed to meet state-of-the-art safety requirements, has been tested and left the
factory in a condition in which it is safe to operate. The device takes into account applicable
standards and regulations which are listed in the EC declaration of conformity and thus meets the
legal requirements of the EC Directives. Endress+Hauser confirms the successful testing of the
device by affixing to it the CE mark.
2.7 Registered trademarks
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
ToF®
Registered trademark of Endress+Hauser GmbH+Co. KG, Maulburg, Germany

Installation Gammapilot M FMG60 with PROFIBUS PA
14 Endress+Hauser
3 Installation
3.1 Incoming acceptance, transport, storage
3.1.1 Incoming acceptance
Check the packing and contents for any signs of damage.
Check the shipment, make sure nothing is missing and that the scope of supply matches your order.
3.1.2 Transport
"Caution!
Follow the safety instructions and transport conditions for devices of more than 18 kg.
3.1.3 Storage
Pack the measuring device so that it is protected against impacts for storage and transport. The
original packing material provides the optimum protection for this.
The permissible storage temperature is
• -40 °C to +50 °C for devices with PVT scintillator
• -40 °C to +60 °C for devices with NaI crystal

Gammapilot M FMG60 with PROFIBUS PA Installation
Endress+Hauser 15
3.2 Installation conditions
3.2.1 Dimensions, weight
Gammapilot M (without water cooling jacket)
L00-FMG60xxx-06-00-00-xx-001
Gammapilot M with water cooling jacket or collimator
L00-FMG60xxx-06-00-00-xx-002
3.2.2 Installation conditions for level measurement
Conditions
• For level measurements the Gammapilot M is mounted vertically; if possible the detector head
should point downwards.
• The exit angle of the source container must be exactly aligned to the measuring range of the
Gammapilot M. Observe the measuring range marks of the Gammapilot M.
Type
Measuring
length A
[mm]
without water cooling
jacket
with water cooling jacket
Overall
length
B [mm]
Weight
[kg]
Overall
length
B [mm]
Weight
without water
[kg]
Weight
including
water
[kg]
NaI 50 621 14 631 18 20
NaI with collimator 50 663 35 ⎯ ⎯ ⎯
PVT 200 780 15 790 20 24
PVT 400 980 16 990 23 29
PVT 800 1380 20 1390 31 40
PVT 1200 1780 24 1790 37 50
PVT 1600 2180 28 2190 45 61
PVT 2000 2580 31 2590 51 72
160 x 190
Æ120
Æ80
537 A
B
160 x 190
537 A
B
16412
Ø140

Installation Gammapilot M FMG60 with PROFIBUS PA
16 Endress+Hauser
• In cascading mode no gap should occur between the measuring ranges of the different
Gammapilot M.
• The source container and the Gammapilot M must be mounted as close to the vessel as possible.
Any access to the beam must be blocked so that no persons or part of their body (hand, arm, head)
may come into the area of the beam.
• In order to enlarge the lifetime, the Gammapilot M should be protected against direct sun. If
necessary, a protective cover should be applied.
• The mounting device FHG60 (see chapter "Accessories) or an equivalent mounting device should
be used for fastening the Gammapilot M.
The mounting device must be installed in a way such that it can withstand the weight of the
Gammapilot M1) under all operating conditions (e.g. vibrations).
!Note!
The Gammapilot M should be given additional support to prevent damage to the connecting cable
or to the unit if it falls off.
Examples
L00-FMG60xxx-17-00-00-xx-001
1: Vertical cylinder; the Gammapilot M is mounted vertically with the detector head pointing downwards; the gamma ray
is aligned to the measuring range. 2: Cascading of multiple Gammapilot M; there is no gap between the measuring ranges.
3: Conical tank outlet (here with sun protection cover); 4: Horizontal cylinder (here with sun protection cover); 5: Wrong:
Gammapilot M mounted inside the tank insulation; 6: Right: Tank insulation removed for Gammapilot M; 7: Support.
1) The weights of the various versions of the Gammapilot M are summarized in the section "Dimensions/Weight".
12
5
6
7
34

Gammapilot M FMG60 with PROFIBUS PA Installation
Endress+Hauser 17
3.2.3 Installation conditions for level limit detection
Conditions
• For level limit detection, the Gammapilot M should be mounted horizontally at the height of the
desired level limit.
• The exit angle of the source container must be exactly aligned to the measuring range of the
Gammapilot M. Observe the measuring range marks of the Gammapilot M.
• The source container and the Gammapilot M must be mounted as close to the vessel as possible.
Any access to the beam must be blocked so that no persons or part of their body (hand, arm, head)
may come into the area of the beam.
• In order to enlarge the lifetime, the Gammapilot M should be protected against direct sun. If
necessary, a protective cover should be applied.
• The mounting device FHG60 (see chapter "Accessories) or an equivalent mounting device should
be used for fastening the Gammapilot M.
The mounting device itself must be fitted in a way such that it can withstand the weight of the
Gammapilot M2) under all operating conditions to be expected.
More information with regard to the safety-related deployment of Gammapilot M can be found in
Safety Manual SD230F/00.
Examples
L00-FMG60xxx-17-00-00-xx-002
Left: maximum fail-safe mode; right: minimum level limit detection
2) The weights of the various versions of the Gammapilot M are summarized in the section "Dimensions/Weight".

Installation Gammapilot M FMG60 with PROFIBUS PA
18 Endress+Hauser
3.2.4 Installation conditions for density and concentration
measurement
Conditions
• If possible, density and concentration should be measured at vertical pipes with a feed direction
from bottom to top.
• If only horizontal pipes are accessible, the path of the ray should also be arranged horizontally to
reduce the influence of air bubbles and sediments.
• The Endress+Hauser clamping device (see chapter "Accessories") or an equivalent clamping
device should be used for fastening the radiation source container and the Gammapilot M to the
measuring tube.
The clamping device itself must be installed in a way such that it can withstand the weight of the
source container3) and the Gammapilot M4) under all operating conditions.
• The sample point may not be further than 20 m from the measuring point.
• The distance of the density measurement to pipe bends is ≥3 x pipe diameter and ≥10 x pipe
diameter for pumps.
Configuration of the measuring system
The configuration of the source container and the Gammapilot M depends on the pipe diameter (or
the length of the irradiated measuring path respectively) and the measuring range. These two
parameters determine the measuring effect (relative change of the pulse rate). The measuring effect
increases with the length of the radiation path through the medium. Therefore, diagonal irradiation
or the use of a measurement section is necessary for small pipe diameters.
For the configuration of the measuring system please contact your Endress+Hauser sales
organization or use the "Applicator" ΤΜ 5)configuration software.
L00-FMG60xxx-17-00-00-xx-003
1: Vertical beam (90°); 2: Diagonal beam (30°); 3: Measurement section;
4: Sample point
!Note!
To increase the accuracy for density measurements, the use of a collimator is recommended. The
collimator screens the detector against environmental radiation.
!Note!
• When planning, the total weight of the measuring system must be taken into consideration.
• The Gammapilot M should be given additional support to secure it against falling or prevent
damage to the connecting cable.
• A clamping device and a measurement section are available as accessories (see chapter
"Accessories").
3) The weights of the source containers are specified in Technical Information TI435F (FQG61, FQG62) and TI346F (QG2000).
4) The weights of the various versions of the Gammapilot M are summarized in the section "Dimensions/Weight".
5) The "Applicator"ΤΜ is available from your E+H sales organization.
1
4
23

Gammapilot M FMG60 with PROFIBUS PA Installation
Endress+Hauser 19
3.2.5 Empty pipe detection
Fig. 1: 1: Monitoring detector DG17/27 or FMG60
Mounting the FMG60 or DG17/27 on the FMG60 for empty pipe detection
If the pipe becomes empty as a result of operational processes, the radiation on the detector side can
hit dangerous levels.
• In such instances, the irradiation channel must be closed immediately for reasons of radiation
protection.
• A high local dose rate also causes the detector unit (scintillator and photomultiplier) to age
quickly.
The best way of avoiding such a situation is to mount a second radiometric measuring system that
monitors the radiation intensity. If high radiation levels occur, an alarm is output and/or the source
container is automatically switched off through pneumatic action for example.
FTG470Z
Gammapilot M
1
SPS / PLC

Installation Gammapilot M FMG60 with PROFIBUS PA
20 Endress+Hauser
3.3 Water cooling
For the versions of the Gammapilot with water cooling jacket, the following applies:
• Material: 316L
• Water connection: 2 x G 1/4"A, DIN ISO 228
• Inlet temperature: max. 40 °C
• Outlet temperature: max. 50 °C (temperature monitoring recommended)
• Water pressure: 4 to 6 bar
L00-FMG60xxx-11-00-00-xx-001
Connections of the water cooling jacket
"Caution!
• It is recommended to ground the water cooling jacket separately at the provided earth terminal
(see above picture)
• The ambient temperature of the compartment housing must not exceed 75 °C. This is also valid,
if water cooling is applied.
3.3.1 Mounting versions
L00-FMG60xxx-17-00-00-xx-009
A: Recommended mounting position for level measurement: compartment housing at the bottom;
B: In exceptional cases (e.g. shortage of space) the compartment housing may be located at the top.
C: Mounting position for level limit detection and density measurement.
"Caution!
The water inlet must always be at the bottom to ensure that the water cooling jacket is completely
filled.
T<75 °CT<120 °C
G1/4"AG1/4"A
*
• The three screws, connecting the pipe
housing to the compartment housing, must
not be opened.
L00-FMG60xxx-05-00-00-xx-052
AB
C