Eneo HDD-2080Z03IR D User manual

EN
Quick Installation Guide
1/3” HDcctv Dome, WDR,
Day&Night, 1920x1080,
3-9mm, 3x AF Zoom, Infrared,
12/24V
HDD-2080Z03IR D

2
Parts supplied
• Dome Camera
• Operating Instruction
• Cable Signal Sticker
• Mounting Template
• Plastic Anchor: 6 x 30mm (3pcs)
• Mounting Screw: 4 x 30mm (3pcs)
• Connector xing Screw: 2.5 x 5mm (1pc)
• Torque Wrench: 3mm (1pc)
• Video Sub-out Cable (1pc)
• Wiring Connector (1pc)
Notes on safety
Please also pay attention to the enclosed safety instructions, and carefully read through
this instruction guide before initial operation.
Important points of warning are marked with a caution symbol.
iImportant points of advice are marked with a notice symbol.

3
EN
Part names
Flush mount
Power cable
OSD control joy stick
3-Axis gimbal
Zoom lens
Safty wire
Dome cover
Bubble dome
Power cable
Video (BNC)
Power supply connector

4
Installation instructions
CAUTION: The camera’s base should be attached to a structural
object, such as concrete, hard wood, wall stud or ceiling rafter
that supports the weight of the camera. If necessary use appro-
priate mounting material (e.g. anchors) instead of the material
enclosed with the camera.
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed.
2. Open the dome cover by loosening screws (4x12mm). Use the torque wrench
supplied.
• Place the dome base unit on pre-drilled position and x it through using mounting
screws (4x30mm).
• Route the Power cable to the connecting place.
3. Set the camera’s viewing angle.
4. Put the dome cover to the dome base unit and tighten the assembly screws.
Optional mounting accessories
For information on optional mounting accessories please visit the eneo website at www.
eneo-security.com.
Plastic Anchor (6x30mm)
Torque Wrench Mounting Screw (4x30mm)

5
EN
Pan & Tilt adjustments
1. Pan limit: Pan is limited to +/- 173°. Do NOT force to rotate the gimbal over the
limit to prevent from the internal damage.
2. Tilt limit: Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when
the inclination of camera module is 0°, that is, the image is aligned horizontally.
3. Inclination limit (Horizontal image alignment): Inclination limited to +/- 50° max.
25º
90º
CAUTION:
Extreme care should be taken NOT to scratch the bubble dome
surface while the camera installing or adjusting.
Care should be taken the cable is NOT to be damaged, kinked or
exposed in the hazardous area.
Tighten enough the dome cover xing screws so that there
should be NO gap between Lens hood and clear bubble to avoid
the light inow from IR LEDs.
Power supply connections
Make sure the power is removed before the installation. Camera can work with either
24AC or 12VDC, dual voltage power. Primary and secondary grounds are completely
isolated to avoid the possible ground-loop problems.
iIn case that HD-SDI/EX-SDI Inputs are not supported in monitor, please use HD-SDI/
EX-SDI Converter to connect HD-SDI/EX-SDI cable with monitor. Some computer moni-
tors or TVs may not support 30p/25p. In this case, HD-SDI/EX-SDI DVR which can convert
Installation instructions
CAUTION: The camera’s base should be attached to a structural
object, such as concrete, hard wood, wall stud or ceiling rafter
that supports the weight of the camera. If necessary use appro-
priate mounting material (e.g. anchors) instead of the material
enclosed with the camera.
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed.
2. Open the dome cover by loosening screws (4x12mm). Use the torque wrench
supplied.
• Place the dome base unit on pre-drilled position and x it through using mounting
screws (4x30mm).
• Route the Power cable to the connecting place.
3. Set the camera’s viewing angle.
4. Put the dome cover to the dome base unit and tighten the assembly screws.
Optional mounting accessories
For information on optional mounting accessories please visit the eneo website at www.
eneo-security.com.
Plastic Anchor (6x30mm)
Torque Wrench Mounting Screw (4x30mm)

6
the frame rate to 60p/50p is highly recommended. Please check specication of monitor
before installation.
Attach the Signal Assignment Sticker in a visible spot for wiring reference.
VIDEO (BNC)
AC24V/DC12V (Red wire)
AC24V/GND (Black wire)
RTX+/RS485 (White wire)
RTX-/RS485 (Gray wire)

7
EN
Operating instructions
Using OSD controller
Setup menu can be accessed and controlled by OSD control joy stick on the side of cam-
era unit. Five commands are available with the joy stick.
Description of the joystick operation
1. SET Key (●) : Access to the menu or enter the setting. To enter the main menu,
press the Set Key down for about 1.5sec
2. UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the cursor up or
down.
3. LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used to adjust the
desired menu selection and to move the cursor left or right.
4. ‘☟’ denotes the long press down straightly for about 2 seconds
Description of the ZOOM&FOCUS adjustment
iWorks only when OSD Menu is inactive.
1. ▲: Zoom In
2. ▼: Zoom Out
3. ◄: Focus Near
4. ►: Focus Far
OSD control Joy Stick
Video format Switch Video Sub-out Connector

8
Set the video format according to system, EX-SDI or HD-SDI
To select the camera’s output video format (EX-SDI or HD-SDI), use the Video format
Switch on the side of the camera (see also“Using OSD controller” for location of the
switch). Only one format can be used at a time. The Video sub-out Connector signal is not
aected by the switch setting.
OSD menu startup
Press ‘●’ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu
mode.
Lens Initializing is strongly recommended at the rst stage of setup menu control. ZOOM/
FOCUS > LENS INIT > Press the joystick‘☟’straight down for about 2 seconds.
1M~120M via RG59u or 5C2V cable
Camera (HD-SDI) DVR (HD-SDI)
Camera (HD-SDI)
1M~120M via
RG59u or 5C2V
cable 350M+ via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
Camera (EX-SDI)
350M+ via RG59u or 5C2V cable
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
350M+ via RG59u or 5C2V cable
Camera (EX-SDI) DVR (EX-SDI)
Camera (HD-SDI) DVR (HD-SDI)
1M~120M via
RG59u or 5C2V
cable
1M~120M via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable

9
EN
MENU V5.xx
1. ZOOM/FOCUS
2. EXPOSURE
3. SCENE ENHANCE
4. 3D-NR
5. DAY/NIGHT
6. PICT ADJUST
7. SPECIAL
8. SYSTEM
9. EXIT
↵
↵
↵
↵
↵
NORMAL
MID
EXT
SAVE&EXIT↵
Direct control menu
MAIN DEFAULT DESCRIPTION
ZOOM/FOCUS - Sets FOCUS and ZOOM relative fuctions.
EXPOSURE -Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP,
AGC and MOTION DEBLUR.
SCENE ENHANCE NORMAL
SCENE ENHANCE provides the several ways to
enhance the video in the various environments
with the settings in NORMAL, WDR,
D-WDR, BLC and HLC.
3D-NR MID Sets 3DNR level. LOW, MID, HIGH
DAY/NIGHT EXT or AUTO
Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and
COLOR D/N. Setting EXT mode for cameras with
IR-LED, AUTO mode for none IR-LED camera
types.
PICT ADJUST Sets WHITE BAL, SHARPNESS, COLOR GAIN,
GAMMA
SPECIAL Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DE-
FECT, TITLE SET, DISPLAY, DEFOG, POINTING ZOOM
SYSTEM Sets TV SYSTEM, RESOLUTION, COMM.SETUP,
LANGUAGE and FACTORY DEFAULT
EXIT
SAVE & EXIT – Exits the menu after saving the
parameters. EXIT – Exits the menu without
saving the menu.
Set the video format according to system, EX-SDI or HD-SDI
To select the camera’s output video format (EX-SDI or HD-SDI), use the Video format
Switch on the side of the camera (see also“Using OSD controller” for location of the
switch). Only one format can be used at a time. The Video sub-out Connector signal is not
aected by the switch setting.
OSD menu startup
Press ‘●’ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu
mode.
Lens Initializing is strongly recommended at the rst stage of setup menu control. ZOOM/
FOCUS > LENS INIT > Press the joystick‘☟’straight down for about 2 seconds.
1M~120M via RG59u or 5C2V cable
Camera (HD-SDI) DVR (HD-SDI)
Camera (HD-SDI)
1M~120M via
RG59u or 5C2V
cable 350M+ via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
Camera (EX-SDI)
350M+ via RG59u or 5C2V cable
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable
DVR (HD-SDI)
350M+ via RG59u or 5C2V cable
Camera (EX-SDI) DVR (EX-SDI)
Camera (HD-SDI) DVR (HD-SDI)
1M~120M via
RG59u or 5C2V
cable
1M~120M via RG59u or
5C2V cable
HDA-3000E
(EX-SDI)
HDA-3000E
(EX-SDI)
1M~120M via
RG59u or 5C2V
cable

10
Further information
The manual is available from the eneo web site at www.eneo-security.com or from the CD
supplied with this product.