Eneo PXB-2080MIR D User manual

Quick Installation Guide
1/3” Network Camera,
Day&Night,H.264,1920x1080,
3D-DNR, infrared, PoE, ONVIF
PXB-2080MIR D
EN

Safety Precaution
03
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
MEGA-PIXEL NETWORK CAMERA

Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
04
MEGA-PIXEL NETWORK CAMERA

Contents
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.08
Part Names
p.09
Installation Instructions
p.10~12
Operating Instructions
p.13~29
Specifications
p.30~31
05
MEGA-PIXEL NETWORK CAMERA

Features
Key Features
06
MEGA-PIXEL NETWORK CAMERA
• Full HD, 2Mega Pixel, NETWORK CAMERA, 1920x1080(30p/25p)
• ONVIF & PSIA Conformance
• Built-in f=2.8~10mm F1.4 Mega pixel DC Auto Iris Vari-focal lens
• Real time true WDR (Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Dual Filter Switcher
• Color D/N, optimized color mode for night
• Various Zooming Technologies
- Pointing Zoom (which enables the programmable zooming at any area)
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
- Preset Zoom
- Flex Zoom
• Day & Night Simulation for easy focus adjustment
• Motion Detection, Privacy Mask, D-WDR, Defog, BLC/HLC, Title Set,
Sens-up, D-Zoom(~8x), Smart IR, AGC, Flickerless, H/V/HV Flip, Deblur
• Top performance at low light sensitivity (Sens-up On)
• H.264 / MJPEG dual streaming
• Slot for Standard SD memory card verified up to 32GB
• Two way Audio & Alarm input /output
• Built-in 40pcs IR-LED
• LED ON/OFF control
• Built-in Cooling fan & Heating function
• External Zoom & Focus Adjustment
• Menu Control via either Local Joystick or WEB
• OSD menu & CVBS Video output BNC for easy installation & maintenance
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• PoE(IEEE Std. 802.3af) & Local dual power
• Dual window
• One-touch 3-Axis locking bracket, Easy installation pad
• IP67 protection

General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accept the infrared light
• With PoE as well as 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
• With Intelligent Focus Indicator and FOCUS ASSIST menu,
- Offers easy adjustment of sharp focus
- Eliminates the mistake of the erratic focus adjustment
Features
07
Composition
Torque Wrench:
3mm (1pc) Video Sub-out
Cable (1pc)
Coupler for
RJ45 Cable (1pc)
Assembly Screw:
4 x 14mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Mounting
Template
Easy
Bracket
Operating
Instruction
Network
Camera
EMI Ferrite Core
(1pc)
Wiring Connector
(1pc)
Cable Signal
Sticker
MEGA-PIXEL NETWORK CAMERA

Dimensions
08
(unit : mm)
267
108
87.30
100
86.40
75.90
80
190
MEGA-PIXEL NETWORK CAMERA

Part Names
09
DUAL WINDOW
ETHERNET &
POWER CABLE
SUNSHIELD BOLT
REAR VIEW
SUNSHIELD
FRONT CASE
EASY
BRACKET
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
FOCUS ZOOM
MEGA-PIXEL NETWORK CAMERA
■Adjustment of viewing angle
with a bracket
Torque
wrench
Lock/Unlock
Screw

• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or
spot light.
Installation Instructions
10
Torque Wrench
Assembly Screw
: 4x14mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the Ethernet & Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x14mm).
5. Set the camera’s viewing angle and adjust zoom/focus of lens by using the torque
wrench.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
CAUTION
REAR VIEW
1
2
3
4
Cable exit
MEGA-PIXEL NETWORK CAMERA