Eneo NLD-1401 User manual

New H.264 Network Camera
Installation Guide
English Version 1.0
Model : NLD-1401

2

3
1. Product Description
This manual applies to the NLD-1401 dome.
The NLD-1401 vandal resistant dome is a Hybrid analogue and IP camera. It
has a standard composite BNC out put allowing it to be connected via coax to a
traditional coax based CCTV system, as well as being connected to an IP based
system.
The NLD-1401 comes supplied with its own viewing software which allows the user
to View, record and configures the camera. Viewing and configuration can also be
carried out via a web browser such as Internet Explorer.
The alarm input and alarm output can be used to connect various third party
devices, such as, door sensors and alarm bells.
Installation Steps
Follow these steps to install the NLD-1401 on your local network (LAN):
1. Check the package contents against the list below.
2. Connect the NLD-1401. See page 5.
3. Set an IP address. See page 5.
4. Set the password. See page 7.
Package Components
The system comes with the following components:
NLD-1401 Installation CD Installation Guide
Contents in the installation CD
1. The NLD-1401 User’s Manual
2. The NT-Manager16 Client Software User’s Manual
3. The NT-Manager16 Installation software

4
2. Installation
For the operation of the NLD-1401, it is necessary to connect: a network cable
for data transmission; a power connection from the supplied power adapter and
possibly a coax cable for standard analogue viewing. Depending on operation
methods, it is possible to connect: alarm cables and audio cable.
Overview
• Top View
NO Name Description
1 Lens Allows wide area to be monitored
2 Extension Cable 26pin camera extension cable
• Extension Cable
NO Wire Color Description
1 Red: AC24V/DC12V
White: AC24V/GND Main Power, 2pin terminal, DC12V/AC24V, max. 6.5W
2 Green: AC24V/DC12V
Black: AC24V/GND Heater Power, 2pin terminal, max. 10Watt @ DC12V, max. 10W @ AC24V

5
3
Pink: Alarm In
Yellowish Green: GND
Yellow: AD Key
Brown: GND
Light Blue: Alarm Out
Gray: GND
Alarm Input, AD Key Input, Alarm Output:
6pin terminal.
4 Black Ethernet, RJ-45 port compatible with 10/100Mbps PoE.
Modular Jack
5 Black Video Composite Output, BNC Jack
6 Gray Audio line output, Stereo Jack
7 Black Audio line input, Stereo Jack
Network Connection
The NLD-1401 supports the operation through the network. Therefore, it is
necessary to connect a standard RJ-45 cable to it. Generally a cross-over cable
is used for directly connection to PC, while a direct cable is used for connection
to a hub.
IP Assignment
When a camera, Encoder or Decoder is first connected to the network it has no
IP address. So, it is necessary to allocate an IP address to the device with the
“Smart Manager” utility on the CD.
1. Connect the NLD-1401 / device to the network and power up.
2. Start SmartManager utility (All Programs>NT-Manager16>SmartManager),
the main window will be displayed, after a short while any network devices
connected to the network will be displayed in the list.

6
3. Select the camera on the list and click right button of the mouse. You can
see the pop-up menu as below.
4. Select Assign IP. You cam see an Assign IP window.
Enter the required IP address.
Note: For more information, refer to the Smart Manger User’s Manual.
3. Operation
The NLD-1401 can be used with Windows operating system and browsers. The
recommended browsers are Internet Explorer, Safari, Firefox and Google
Chrome with Windows.
Notes: To view streaming video in Microsoft Internet Explorer, set your browser
to allow ActiveX controls.
3.1 Access from a browser
1. Start a browser (Internet Explorer).
2. Enter the IP address or host name of the NLD-1401 in the Location/ Address
field of your browser.
3. You can see a starting page. Click Live View or Setup to enter web page.

7
4. The encoder’s Live View page appears in your browser.
3.2. Access from the internet
Access from the internet once connected, the NLD-1401 is accessible on your
local network (LAN). To access the NLD-1401 from the Internet you must
configure your broadband router to allow incoming data traffic to the it. To do
this, enable the NAT-traversal feature, which will attempt to automatically
configure the router to allow access to the NLD-1401. This is enabled from
Setup > System > Network > NAT.
For more information, please see NAT traversal (port mapping) for IPv4, on
page 61, the User’s Manual.
3.3 Setting the administrator password
T
o gain access to the product, the
password for the default administrator user
must be set. This is done in the “Admin
Password” dialog, which is displayed when
the NLD-1401 is accessed for the setup at
the first time. Enter your admin name and
password, set by the administrator.
Note: The default administrator username
and password is “admin”. If the password
is lost, the NLD-1401 must be reset to the
factory default settings. See page 10.

8
3.4 Live View Page
T
he live view page comes in
eight screen modes like
704x480(576), 704x240(288),
352x240(288), 176x120(144),
640x480, 320x240, and
160x120. Users are allowed to
select the most suitable one out
of those modes. Please, adjust
the mode in accordance with
your PC specifications and
monitoring purposes.
• General controls
The video drop-down list allows you to select a customized or pre-
programmed video stream on the live view page.
The resolution drop-down list allows you to select the most
suitable one out of video resolutions to be displayed on live view page.
The protocol drop-down list allows you to select which
combination of protocols and methods to use depends on your viewing
requirements, and on the properties of your network.
• Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the
following buttons:
The Stop button stops the video stream being played.
The Pause button pause the video stream being played.
The Snapshot button takes a snapshot of the current image. The location
where the image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image
on the live screen.
The Full Screen button causes the video image to fill the entire screen area.
No other windows will be visible. Press the 'Esc' button on the computer
keyboard to cancel full screen view.
The Manual Trigger button activates a pop-up window to manually start or
stop the event.
The Camera Menu button activates a pop-up window for camera menu
control.

9
Use this scale to control the volume of the speakers.
Use this scale to control the volume of the microphone.
Use this scale to control the volume of the speakers and microphones.
• Camera Menu controls
If the NLD-1401 has been appropriately configured, the Live View page displays
the controls available for the OSD menu.
For more information, please see “3.8 Camera Menu Control” on the User’s
Manual.
• Video and Audio Streams
The camera can provide several images and video stream formats. Your
requirements and the properties of your network will determine the type you
use.
The Live View page in the camera provides access to H.264, MPEG-4 and Motion
JPEG video streams, and to the list of available video streams. Other
applications and clients can also access these video streams/images directly,
without going via the Live View page.
3.5 Setup
This section describes how to configure the NLD-1401, and is intended for
product Administrators, who have unrestricted access to all the Setup tools; and
Operators, who have access to the settings for Basic, Live View, Video & Image,
Audio, Event, and System Configuration.
You can configure the NLD-1401 by clicking Setup in the top right-hand corner
of the Live View page. Click on this page to access the online help that explains
the setup tools.
When accessing the NLD-1401 for the first time, the “Admin Password” dialog
appears. Enter your admin name and password, set by the administrator.

10
When accessing the NLD-1401 for the first
time, the “Admin Password” dialog
appears. Enter your admin name and
password, set by the administrator.
If the password is lost, the NLD-1401 must
be reset to the factory default settings.
3.6 Resetting to the factory default settings
To reset the NLD-1401 to the original factory settings, go to the Setup>System
>Maintenance web page (described in “3.6.5.6 Maintenance” of the User’s
Manual) or use the control button on the NLD-1401, as described below:
Follow the instructions below to reset the NLD-1401 to the factory default
settings using the Reset Button.
1. Switch off the NLD-1401 by disconnecting the power adapter.
2. Press and hold the Control Button with a straightened paperclip while
reconnecting the power.
3. Keep the Control button pressed until the Status and Power indicator blink.
4. Release the Control Button.
5. When the Power Indicator changes to Green (may take up to 1 minute), the
process is complete and the NLD-1401 has been reset.
6. The NLD-1401 resets to factory defaults and restarts after completing the
factory reset.
CAUTION: When performing a Factory Reset, you will lose any settings you
have saved.
3.7 More Information
For more information, please see the NLD-1401 User’s Manual, which is
available on the CD included in this package.