Eneo MEC-52C0000M0A User manual

EN
User Manual
1/2.8” HD Camera, Day&Night,
1920x1080, D-WDR, C/CS,
12VDC
MEC-52C0000M0A

ULTRA CLEAR RESOLUTION CAMERA
Safety Precaution
03
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

ULTRA CLEAR RESOLUTION CAMERA
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
04

ULTRA CLEAR RESOLUTION CAMERA
Contents
Safety Precaution
p.03~04
Contents
p.05
Features
p.06
Composition
p.07
Dimensions
p.07
Part Names
p.08
Installation Instructions
p.09
Operating Instructions
p.10~27
Specifications
p.28
05

ULTRA CLEAR RESOLUTION CAMERA
Features
Key Features
06
• 1/2.8” SONY Exmor CMOS sensor
• 1080P TVI mode, CVI mode, AHD Video or 960H CVBS Video Selectable
• TVI mode/CVI mode/AHD Video Transmission Distance over Coax.; 500M
• CS lens mount supported
• Automatically removable IR Cut filter by Dual filter switcher
• Sensitivity of Color 0.3 Lux / BW 0.005 Lux (@IRE 40, Sens-up On)
• D-WDR (Wide Dynamic Range)
• Improved noise reduction 2D+3DNR(TVI mode/CVI mode/AHD), 2DNR(CVBS)
• FOCUS ASSIST for Error free focus adjustment
• 2 Auto(AE/AWB) control
• LSC (Lens Shading Compensation)
• DPC (Defective Pixel Compensation)
• Motion detection, Privacy mask, BLC/HSBLC, Defog, Sens-up(~x30),
Mirror/ Flip, Freeze, Negative Image, IR Smart, Cam Title
• Fine Back focus adjustment
• OSD MENU & CVBS output for easy installation & maintenance
• Circuit protection against faulty connection in power polarity
• Power: DC12V

ULTRA CLEAR RESOLUTION CAMERA
(unit : mm)
07
Dimensions
Composition
Torque Wrench:
3mm (1pc)
Dust Protection
Cap (1pc)
Operating
Instruction
Box Camera
72
74 82
89
Ø35
C-mount
adaptor (Option)

ULTRA CLEAR RESOLUTION CAMERA
④
①OSD Control &
Video Format Joystick
②Power Input Terminal
③ Video Format DIP Switch
④ Power LED
⑤Video Output Connector(BNC)
③
①⑤
②
Part Names
08
Torque
Wrench
Dust
Protection Cap
No.
1
2
3
4
DC Iris
Damp(-)
Damp(+)
Drive(+)
GND
Front Case
Rear Case
Back focus
adjustment
Mount Holes
(Top / Bottom)
SIDE VIEW
Lens Connector
for Auto Iris lenses
PIN 1PIN 3
PIN 2PIN 4
REAR VIEW
CVBS HD
DC12V

ULTRA CLEAR RESOLUTION CAMERA
Installation Instructions
09
Power Supply Connections
1. Remove the dust protection cap from the lens mount.
2. Screw the lens onto the camera firmly.
3. Plug the lens plug into the lens connector on the side of camera case.
4. Mount the camera to the wall or ceilling with a corresponding mounting bracket
through the camera mount holes (1/4” thread insert) on its top or bottom.
CAUTION
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• Follow the order for applying power.
First connect the low voltage (DC12V or AC24V), then plug the DC or AC
adapter to DC or AC outlets to avoid an improper reset from power jitter and
a damage from the surge voltage when no load.
• Care should be taken the cable is NOT to be damaged, kinked or exposed in
the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or
spot light.
Setting the back focus adjustment
The proper back focus adjustment is essential for the motorized zoom lens to
get the all time sharp focus when zooming in and out by the remote control.
For easier and better adjustment, this camera provides FOCUS ADJUST menu
which prevents from the mistake of the focus adjustment.
With enabling FOCUS ADJUST menu, follow the procedure to get the best back
focus adjustment.
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).
2. Shoot the object departing from about 10Meters.
3. Adjust ’Back focus adjustment’ with 3mm L-wrench until the optimum focus is
achieved.
4. Set the lens for zoom position to TELE and adjust the lens focus for best focus .
5. Set the lens for zoom position to WIDE again, check if the focus adjustment
was the best. If not, re-adjust ‘Back focus adjustment’ slightly.
Camera can be operated with the regulated or unregulated DC12V but the
regulated power supply of DC12V is recommended.
Camera is protected from the damage by the reverse connection of polarity.

ULTRA CLEAR RESOLUTION CAMERA
Operating Instructions
10
CVBS HD
DC12V
OSD Control &
Video format Joystick
Using OSD Control Controller
Setup menu can be accessed and controlled by OSD control joystick on the
rear of the camera unit. Five commands are available with the joystick.
The design of OSD could be different according to the Models.
1] SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2] UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3] LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used
to adjust the desired menu selection and to move the cursor left or right.
Video format
DIP Switch
■ Description of the OSD control operation
If OSD menu is adjusted in specific video format, adjusted value is applied to
only related video format. For example, if the menu is adjusted in CVBS mode,
adjusted value is applied to CVBS video only.
NOTE
Using Video Format Switch
■DIP SWITCH setting
The DIP SWITCH setting has first priority.
If the switch is set to CVBS, only CVBS output is available for both main video
output and sub-out. Please be advised that camera generates only one video
output for both main video output and sub-out. It takes 3~5 seconds when video
format is changing. The default DIP SWITCH setting is CVBS mode.