Eneo TVB-2080Z10IR User manual

User Manual
1/3” HD-TVI Camera, Day&Night,
1920x1080, WDR, 10x AF Zoom,
Infrarot, 12/24V
TVB-2080Z10IR
EN

Safety Precaution
03
FULL-HD AF-ZOOM CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

Safety Precaution
04
FULL-HD AF ZOOM CAMERA
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

Contents
05
FULL-HD AF ZOOM CAMERA
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.08
Part Names
p.08
Installation Instructions
p.09~11
Operating Instructions
p.12~27
Specifications
p.28

Features
Key Features
06
FULL-HD AF ZOOM CAMERA
• Full HD, 2Mega Pixel HD-TVI CAMERA, 1920x1080(30p/25p)
• TVI Video Transmission Distance over Coax.; 500M (RG59, 75Ω)
• Automatically removable IR Cut filter by Dual filter switcher
• Built-in f=5.1~51mm, F1.6~F1.8 Day & Night zoom lens
(Optical 10x Auto focus zoom / Digital 32x zoom)
• True WDR(Wide Dynamic Range)
• Improved Noise figure with the enhanced 2D+3DNR
• Preset Zoom
• Home Position setting
• Intelligent Motion Detection, Privacy Mask
• Lens Refresh, E.Zoom, Flickerless, BLC, HLC, H/V/HV Mirror,
Defog, Freeze, Defect Detection, DSS(Sens-up), ACE(D-WDR),
Sharpness, HD Format
• ID / TITLE / INITIAL MESSAGE / ZOOM RATIO DISPLAY
• Enhanced Sensitivity by DSS technology
• Improved DIS(Digital Image Stabilization) function
• Selectable Digital output 1080p or 720p
• OSD menu & Video sub-out for easy installation & maintenance.
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-C/Hikvision)
• UTC Control through HD-TVI DVR
• Built-in 4pcs High-power LED
• Dual Window
• One-touch 3-Axis locking bracket, Easy Installation Pad
• IP67 Protection
• AC24/DC12V Dual power

General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by adopting Auto Focus Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
Features
07
FULL-HD AF ZOOM CAMERA
Composition
Mounting Template
Operating
Instruction
Camera
Torque Wrench:
3mm (1pc)
Video Sub-out
Cable (1pc)
Assembly Screw:
4 x 15mm (4pcs)
Mounting Screw:
4 x 30mm (4pcs)
Plastic Anchor:
6 x 30mm (4pcs)
Easy
Bracket
Cable Signal
Sticker
Wiring Connector:
(1pc)

Dimensions
08
FULL-HD AF ZOOM CAMERA
(unit : mm)
Part Names
267
108
87.30
100
86.40
75.90
80
190
POWER
CABLE
DUAL WINDOW
SUNSHIELD BOLT
SUNSHIELD
FRONT CASE
EASY
BRACKET
OSD Setup
CONTROL COVER
LOCK/UNLOCK
SCREW
BRACKET
REAR CASE

Installation Instructions
09
FULL-HD AF ZOOM CAMERA
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun
or spot light.
Torque Wrench
Assembly Screw
: 4x15mm
Mounting Screw
: 4x30mm
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws(4x30mm). Skip this step when an easy bracket is not installed.
3. Route the power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Fix the camera bracket through using assembly screws (4x15mm).
5. Set the camera’s viewing angle.
6. Put the sunshield to the camera unit and tighten the sunshield-bolts.
CAUTION
REAR VIEW
1
2
3
4
Cable exit

Installation Instructions
10
FULL-HD AF ZOOM CAMERA
• Unlock the screw on the camera bracket through using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
88°
90°
±90°
• on the wall • on the ceiling
■Adjustment of viewing angle with a bracket
Torque
wrench
Lock/Unlock
Screw

Installation Instructions
11
FULL-HD AF ZOOM CAMERA
※ Attach the Signal Assignment Sticker
in a visible spot for wiring reference.
VIDEO (BNC)
AC24V/GND (Black wire)
AC24V/DC12V (Red wire)
RTX-/RS485 (Gray wire)
RTX+/RS485 (White wire)
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• Follow the order for applying power.
First, connect the low voltage (AC24V or DC12V), then plug the AC adapter to
AC outlets to avoid an improper reset from power jitter and a damage from the
surge voltage when no load.
Power Supply Connections
Camera can work with either 24VAC or 12VDC, dual voltage power.
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems

Operating Instructions
12
FULL-HD AF ZOOM CAMERA
Setup menu can be accessed and controlled by OSD control joy stick on the
side of camera unit.
Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Cover Open
Using OSD controller
Video Sub-out
Connector
OSD Control
Joy Stick
SUB-OUT
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) ‘ ’denotes the long press down straightly for about 2 seconds
Description of the ZOOM&FOCUS* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
3) ◄: Focus Near
4) ► : Focus Far
(*) Works only when OSD Menu is inactive.
Set to E-ZOOM ON for Digital zoom control.
ZOOM

Operating Instructions
13
FULL-HD AF ZOOM CAMERA
OSD menu Startup
Press ‘☟’OSD MENU key down to access the setup menu mode.
OSD menu Table
MAIN MENU SUB MENU CONFIGURATION
ZOOM/FOCUS
EXPOSURE
DISTANCE
FOCUS
MODE
AGC
SHUT SPEED
IRIS
max. x2~x19, x21, x23, x25, x28, x32
1~5
OFF, ON
0.1m, 1.0m, 3.0m, 5.0m, 10.0m
0~7
ONE PUSH
1DAY~10DAYS
AUTO, ONE PUSH, MANUAL
OFF,
0~20
PRESET
MODE
AUTO/ IRIS.P/ SHUT.P/ MANUAL
OFF/ON (0~10)
30/25fps]
x4, x2, 1/30(25), 1/60(50), 1/120(100), 1/250~1/30,000sec
*60/50fps]
x8, x4, x2, 1/60(50), 1/120(100), 1/250~1/30,000sec
ZOOM SPEED
LENS REFRESH
E.ZOOM
ZOOM PRESET
• EXIT : Exits the setup menu without save.
• SAVE : Saves the menu settings.
• DFLT : Reset to the factory defaults.
• BACK : Go back to the previous menu.
MENU
ZOOM/FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[ EXIT ] [ SAVE ] [ DFLT ]
DWELL TIME 3sec~60sec
OFF/ON
HOME POSITION

Operating Instructions
14
FULL-HD AF ZOOM CAMERA
DSS 30/25fps] OFF/ x2, x4
*60/50fps] OFF/ x2, x4, x8
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
FLICKERLESS
BRIGHTNESS
BLC/WDR/HLC
DAY&NIGHT
MODE
RED GAIN
BLUE GAIN
CHROMA
PRIVACY
FREEZE
GAMMA
DNR
MIRROR
SHARPNESS
ACE
DEFOG
LEVEL
POSITION, SIZE
LEVEL(0~20), COLOR(0~13)
0~255sec
0~28
LOW, MID-LOW, MIDDLE,
MID-HIGH, HIGH
OFF, ON
OFF, ON
LOW, MID-LOW, MIDDLE,
MID-HIGH, HIGH
OFF, ON
AUTO, ONE PUSH, MANUAL, INDOOR, OUTDOOR
OFF/ON
0~20
OFF
WDR
BLC
HLC
AUTO
EXT-IN
DAY
NIGHT
DELAY
THRS
GAP
IR DETECTION
IR DET LEVEL
BURST
DELAY
BURST
POLARITY
BURST
0~20 (control only in MANUAL mode)
0~20 (control only in MANUAL mode)
0~20
OFF/ON
OFF/ON
OFF, ON
0.45/ 0.55/ 0.65/ 0.75
0~20
MID-HIGH, HIGH, LOW,
MID-LOW,MIDDLE
0~255sec
OFF, ON
ACTIVE LOW, ACTIVE HIGH
MODE
LEVEL
MASK
MODE
POSITION
SIZE
AUTO, MANUAL
LOW, MIDDLE, HIGH
1~24
OFF, ON
OFF, LOW, MIDDLE, HIGH, AUTO
OFF, H, V, H&V
0~10
OFF, LOW, MIDDLE, HIGH

Operating Instructions
15
FULL-HD AF ZOOM CAMERA
PRIVACY
DIS
OFF/ON
MOTION OFF/ON
COLOR
TRANS
0~13
0~4
1~3
OFF, ON
0~20
AREA#
MODE
SENSITIVITY
POSITION
OFF/ON 10%, 20%, 30%
LOW, MIDDLE, HIGH
OFF, HALF, FULL
RANGE
FILTER
AUTO C
INTELLIGENCE
SPECIAL FUNC
DISPLAY
DEFECT
IMAGE RANGE
SYSTEM
HD FORMAT
COMM
DISP SEL
SET TITLE
INIT SEL
SET INIT MSG
LANGUAGE ENGLISH, Simplified CHINESE, Traditional CHINESE,
JAPANESE
NTSC(30/60fps) or PAL(25/50fps)
FULL
COMP
USER
ID, BAUD RATE, PROTOCOL
1080p /30(25)fps, *1080p /60(50)fps, 720p/30(25)fps,
*720p/60(50)fps
(*) Not Supported
OFF/ON
OFF/ON
LEVEL (0~32)
ID, TITLE, ZOOM RATIO, SYSTEM MSG
ID, BAUDRATE, PROTOCOL, VERSION,
INIT MSG
0~255
0~255
OFF, ON
SIZE
INTERVAL
DWELL TIME
ZOOM PRESET

Operating Instructions
16
FULL-HD AF ZOOM CAMERA
• AUTO: Focusing is always working.
• ONE PUSH: Focusing is activated only when pressing the SET key on OSD
control.
• MANUAL: Focusing can be adjusted by ▲,▼ of OSD control joystick or the
remote control.
• ONE PUSH: Lens refreshing is activated only when pressing the SET key on
OSD control.
• 1~10days: Can be set from 1 to 10 days and performs the scheduled LENS
Initialization automatically. Every initialization occurs when the time reaches
the scheduled time after setup or power up. When LENS REFRESH initiates
LENS Initialization, a notification ‘LENS INITIALIZING…’ appears on the monitor.
: AUTO, ONE PUSH and MANUAL modes are available for focusing.
1-1. FOCUS (default: AUTO)
: Set the minimum distance in focus between camera and objects.
Select from 0.1m to 10.0m
1-2. DISTANCE (default: 1.0m)
: Set the zoom speed from 0(slow) to 7(fast)
1-3. ZOOM SPEED (default: 7)
: Lens origin calibrated automatically. ONE PUSH and ON modes are available.
1-4. LENS REFRESH (default: ONE PUSH)
OSD menu Setup
1. ZOOM/FOCUS
ZOOM/FOCUS
FOCUS
DISTANCE
ZOOM SPEED
LENS REFRESH
E.ZOOM
ZOOM PRESET
HOME POSITION
1.0m
7
ONE PUSH
OFF
OFF
[ BACK ] [ SAVE ] [ DFLT ]
MENU
ZOOM/FOCUS
EXPOSURE
WHITE BAL
IMAGE
INTELLIGENCE
SPECIAL FUNC
DISPLAY
[ EXIT ] [ SAVE ] [ DFLT ]

Operating Instructions
17
FULL-HD AF ZOOM CAMERA
: E-ZOOM is available up to 32x. It starts working when the optical zoom
reaches its maximum tele-position. Zoom ratio is displayed on the right bottom
corner of the monitor if DISPLAY>DISP SEL>ZOOM RATIO is set to ON.
1-5. E. ZOOM (default: OFF)
: Set the ZOOM PRESET. Able to Zoom in for the preset area by PTZ controller.
1-6. ZOOM PRESET
※ If the motion detection is turned on, E.ZOOM function is inactivated.
• PRESET # : Set a number to select a zoom preset up to 5. It works when the
MODE menu is set to ON.
• MODE: Set to ON, the ZOOM function is activated as PRESET number setting
and zoom position can be adjusted.
1-7. HOME POSITION
: Camera can be configured to return to pre-defined Zoom position automatically
after certain period since ZOOM IN/OUT control is accomplished.
Set the optical zoom position as HOME POSITION in OSD controller or PTZ
controller.
• DWELL TIME: When ZOOM IN/OUT control is accomplished, camera returns
to pre-defined Zoom position after Dwell time.
●Move the cursor in the MENU :
Moves UP/DOWN/LEFT/RIGHT Joy stick
●Enter the MENU :
Press buttons 9+5+PSET (PRESET)
●Select or Choose value in the MENU: Press button OPEN (IRIS OPEN)
●Set the Preset Zoom :
Press buttons 1(or ~5)+PSET (PRESET)
TIP
Setting for Zoom Function with PTZ Controller
1
●Zoom IN: Press button TELE or Spin the joystick to clockwise.
●Zoom OUT: Press button WIDE or Spin the joystick to counter-clockwise.

Operating Instructions
18
FULL-HD AF ZOOM CAMERA
: Set the Auto Gain Control. If you set to AUTO, SHUT.P or IRIS.P in the MODE
menu, it can be selected OFF or ON.
If set to MANUAL in the MODE menu, it can be adjusted from 1 to 10 levels.
AGC amplifies the video gain for brighter video but noise and white pixel
accordingly.
: It can be set in SHUT.P or MANUAL mode. Selects shutter speed level.
2-2. AGC (default: ON)
2-3. SHUT SPEED
• AUTO: Optimizes the video level by controlling the iris and the shutter speed
automatically.
• IRIS P: If you set to IRIS.P mode, it can be adjusted IRIS value.(refer to 2-4.IRIS)
Selects to fix IRIS in a certain apperture and the video level is controlled by an
automatic shutter control. Too much low IRIS LEVEL will result in the foggy
video by the diffusion from the lens iris.
• SHUT. P: Selects to fix SHUTTER speed in a certain speed and the video level
is controlled by an automatic iris control. If you set to SHUT.P mode, it can be
adjusted SHUT SPEED value. (refer to 2-3.SHUT SPEED)
This mode is useful when the color rolling occurs under the fluorescent lighting.
It is not recommendable at outdoor in the daytime.
• MANUAL: Iris, Shutter speed and AGC can be set manually.
2. EXPOSURE
: Can set EXPOSURE MODE to AUTO, IRIS P, SHUT. P, and MANUAL.
2-1. MODE (default: AUTO)
EXPOSURE
MODE
AGC
SHUT SPEED
IRIS
DSS
FLICKERLESS
BRIGHTNESS
BLC/WDR/HLC
DAY&NIGHT
ON
---
---
OFF
OFF
8
OFF
EXT-IN
[ BACK ] [ SAVE ] [ DFLT ]

Operating Instructions
19
FULL-HD AF ZOOM CAMERA
• 60/50fps (Not Supported)
: x8, x4, x2, 1/60(50),1/120(100), 1/250, 1/700, 1/1000, 1/1600, 1/2500,
1/5000,
1/7000, 1/10000, 1/30000sec
: It can be set in IRIS.P or MANUAL mode. Selects iris value from 0 to 20.
2-4. IRIS
: Sets the maximum digital slow shutter speed. It can be controlled in AUTO,
IRIS.P modes
2-5. DSS (Digital Slow Shutter) (default: OFF)
: Adjusts the brightness valur of video from 0 to 20.
2-7. BRIGHTNESS (default: 8)
: Select WDR(Wide Dynamic Range) , BLC(Back Light Compensation) or
HLC(High Light Compensation) functions.
2-8. BACK LIGHT (default: OFF)
• 30/25fps : x4, x2, 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1000, 1/1600,
1/2500, 1/5000, 1/7000, 1/10000, 1/30000sec
• 60/50fps (Not Supported) : OFF, x2, x4, x8
• 30/25fps : OFF, x2, x4
: This function is used to remove the flickering on screen due to differences in
light and electric frequencies. Selects OFF or ON.
2-6. FLK LESS (default: OFF)
2-8-1. WDR(Wide Dynamic Range):
: This function is extended the gain range of the screen that is mostly useful
if camera takes a simultaneous picture of both indoor and outdoor nearby
• LEVEL (default:MIDDLE)
: Adjust WDR level. LOW, MID-LOW, MIDDLE, MID-HIGH, HIGH
window. It improves contrast of the picture in outdoor scenery as well as
indoor. Video outputs image processed from two images by dual shutter
(long and short shutter) in a field to provide the best dynamic range.
Highlight area is compensated by the short shutter and dark area is com-
pensated by the long shutter.
※CVBS video signal:Connecting 2nd video to CVBS port disables D-WDR
function temporary. It should be considered when installer adjusts the video
with installation monitor via CVBS video signal.

Operating Instructions
20
FULL-HD AF ZOOM CAMERA
※ BLC function is inactivated in MANUAL mode of EXPOSURE menu.
: This function is used to brighten an image in the foreground with a highly
light area behind it such as sunlight, limiting the affect of silhouette.
2-8-2. BLC (Back Light Compensation):
• POSITION: Adjust the window position
• SIZE: Adjust the window size
• LEVEL: Can set the highlight value from 0 to 20 for HLC working.
• COLOR: Can set the masking color on the highlight area.
0 is Black, from1 to 6 are Gray scale,
7 is White,
8 is Red,
9 is Green,
10 is Blue
11 is Blue-green
12 is Yellow
13 is Magenta
2-9. DAY & NIGHT
2-8-3. HLC (High Light Compensation):
: This function is used to control the setting during day-time and night-time
operation.
: HLC(High Light Compensation) function is used to black out highlighted areas,
in order to enable a clear visual image of objects, such as the license plates
of an oncoming vehicle or other objects that may be obstructed by headlamps.
HLC clips out the highlight area and masks it as black color.
Video will be masked for the area which exceeds LEVEL.
2-9-1. EXT-IN
: The camera switches DAY
from/to NIGHT automatically
using the detected brightness
level by photocell.
• DELAY:
It is time in second while camera
maintains its status before Day
↔Night switches. DELAY can
avoid the unwanted/frivolous
switching by a short term lights such as light from the passing car.
DAY&NIGHT
DELAY
BURST
POLARITY
ON
ACTIVE HIGH
[ BACK ] [ SAVE ] [ DFLT ]