Energizer EZN1800 User manual

HIGH PRESSURE WASHER
EZN1800/EZN1800-UK
EZN2000/EZN2000-UK
EZN2200/EZN2200-UK
USER GUIDE
CAUTION Read the instructions before using the machine
ORIGINAL INSTRUCTIONS

©2020 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC
and related subsidiaries and are used under license by Builder SAS.

Let’s get started.
You’re excited to power up, so we’ll keep this brief!

4
CONTENTS
1. SAFETY WARNINGS 5
2. INTENDED USE 11
3. SYMBOLS 11
4. ASSEMBLY INSTRUCTIONS 13
5. OPERATING INSTRUCTIONS 19
6. INFORMATION FOR USAGE 20
7. CLEAN-UP AND STORAGE 24
8. CLEANING TIPS 25
9. TECHNICAL DATA 26
10. TROUBLESHOOTING TIPS 27
11. WARRANTY 28
12. PRODUCT FAILURE 29
13. WARRANTY EXCLUSIONS 30
14. DECLARATION OF CONFORMITY 31

5
1. SAFETY WARNINGS
• Use this unit as described in this manual. Any mishandling
and any use contrary to instructions shall in no case be the
responsibility of the manufacturer.
• Failure to observe the safety and operating instructions may
result in a risk of electric shock, re and/or personal injury.
• If you are giving this unit to another person, please also pro-
vide this manual.
• Do not use attachments other than those recommended by
the manufacturer; they can damage the unit and/or cause
injury.
• Machines should not be used by children. Children should
be supervised to ensure that they do not play with the
appliance.
• This machine can be used by people with reduced physi-
cal, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or ins-
truction concerning use of the machine in a safe way and
understand the hazards involved.
• Children must not play with the appliance.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
• Before any connection, check:
▪The appliance, power cable and accessories are not
damaged. In this case, do not use the appliance and
take it to your dealer for inspection and repair.
▪The voltage indicated on the rating plate of the
appliance corresponds to that of your electrical
installation.
▪Do not disassemble the device yourself. Any
disassembly, repair or inspection should be carried out
exclusively by a qualied person.

6
▪Do not touch the plug with wet hands. Do not allow the
plug to fall into the water.
▪Do not walk on the power cord, do not exert excessive
pressure, or pull on the cord to avoid damage.
WARNING!
• This machine has been designed for use with a cleaning
agent supplied or recommended by the manufacturer. Use
of other cleaning or chemical agents may a󰀨ect the safety
of the machine.
WARNING!
• High pressure jets can be dangerous if subject to misuse.
The jet must not be directed at persons, live electrical
equipment or the machine itself.
WARNING!
• Do not use the machine within range of persons unless they
wear protective clothing.
WARNING!
• Do not direct the jet against yourself or others in order to
clean clothes or footwear.
WARNING!
• Risk of explosion! Do not spray ammable liquids.
WARNING!
• High pressure cleaners shall not be used by children or
untrained personnel.
WARNING!
• The machine should be disconnected from its power source
during cleaning or maintenance and when replacing parts or
converting the machine to another function.

7
WARNING!
• High pressure hoses, ttings and couplings are important
for the safety of the machine. Use only hoses, ttings and
couplings recommended by the manufacturer.
WARNING!
• To ensure the safety of the machine, use only the original
manufacturer’s parts or parts approved by the manufacturer.
WARNING!
• Water that has owed through backow preventers is consi-
dered to be not drinkable.
WARNING!
• The machine must be disconnected from the power supply
during cleaning or maintenance and when replacing parts or
converting the machine to other functions by removing the
power source plug.
WARNING!
• Do not use the machine if a supply cord or important parts
of the machine are damaged, e.g. safety devices, high pres-
sure hoses, trigger gun.
WARNING!
• If an extension cord is used, the plug and cable must be
watertight.
WARNING!
• Inadequate extension cords can be dangerous. If an exten-
sion cord is used, it should be suitable for outdoor use,
and the connection has to be kept dry and o󰀨 the ground.
It is recommended that this is accomplished by means of a
cord reel which keeps the socket at least 60mm above the
ground.
WARNING!
• Make sure there are no exhaust emissions near the air
intakes.

8
• Children, animals and persons not participating in the use
of the machine must remain at a minimum distance of 10
metres from the sprayer.
• The high pressure hose must remain connected to the com-
pressor as long as the system is under pressure.
• Do not use corrosive or ammable liquids in the machine.
• The appliance must be connected to a water supply using a
new set of hoses; the old pipe set must not be reused.
• Make sure that there are no exhaust emissions near the air
inlets.
• When using the machine, wear protective equipment inclu-
ding safety goggles, safety shoes, safety gloves, safety
helmet with visor and double-insulated hearing protection.
• In order to move the unit easily, bend the lance.
• Make sure the unit is turned o󰀨 and unplugged before trans-
porting the unit.
• The connection to the power supply must be made by a
qualied electrician in accordance with IEC60364-1. It
is recommended that the power supply of this machine
includes a residual current device that interrupts power if
the earth leakage exceeds 30mA for 30ms with an homolo-
gated earth circuit.
• Before assembling, dismantling, repairing, transporting,
servicing and storing, please check if the appliance is dis-
connected from the power supply.
• Handle the unit with care, do not drop it.
• Do not use the machine in extreme weather conditions,
when it is very cold. Do not use the machine with ice water.
• Use the tool in a stable and level location.
• The inlet hose can be connected to the water mains with a
maximum pressure of 10 bars.

9
WARNING!
• In order to avoid any danger due to the accidental reset of
the thermal circuit breaker, this device must not be powered
via an external switch, such as a timer, or be connected to
a circuit which is regularly connected switched on and o󰀨 by
the electricity supplier.
• The appliance must not be connected to drinkable water
supply.
CAUTION!
• In order to avoid danger due to untimely resetting of the
thermal cut-out, this device must not be powered by an
external switch, such as a timer, or connected to a circuit
that is regularly switched on energized and de-energized by
the electricity supplier.
• When transporting the machine, take note of its weight. Do
not overestimate your e󰀨orts and get help if necessary.
• If the machine must be transported from one point to ano-
ther, please disconnect it. Always use the handle to push
the machine.
• Use the handle to lift the machine.
• Improper transport of the machine may result in accidents
and injuries.
• Do not use the tool where dangerous situations or accidents
may occur. Do not use indoors, or in places where there are
exhaust gases, etc.
• In case of an accident or malfunction, stop using the tool,
switch o󰀨 and unplug. Check the conditions of the tool and
bring it to a service agent for inspection and reparation if
necessary.
• When opening the trigger gun, pay attention to the kickback
force. The power of the gun can cause a kickback and can
produce a loss of control of the gun and create accidents
and injuries. Hold the gun rmly, and with both hands if pos-
sible.

10
WARNING!
• Always switch o󰀨 the mains disconnecting switch when
leaving the machine unattended.
• To avoid dangerous situations in the event of an accident
(for example, contact with or spill of detergents) or equip-
ment failure (such as a puncture or a component failure),
please stop using the machine immediately. Check the pro-
blem. Have the machine inspected by a qualied technician.
In the event of an overow, move the machine away and
clean the overow.
WARNING!
• Always turn o󰀨 the main switch when leaving the machine
unattended.
• The tool must always remain upright during use, transport,
testing, assembly and disassembly.
• Do not use the tool in dangerous situations or when an acci-
dent has occurred.
• Do not use indoors, in places where gases can be emitted,
etc.
RESIDUAL RISKS
• Even if you are operating this product in accordance with
all the safety requirements, potential risks of injury and
damage remain. The following dangers can arise in connec-
tion with the structure and design of this product:
▪Health defects resulting from vibration emission if the
product is being used over long periods of time or not
adequately managed and properly maintained.
▪ Danger of injury and property damage caused by ying
objects.
▪ Injuries and damage to property due to broken
accessories or the sudden impact of hidden objects
during use.

11
2. INTENDED USE
Your high pressure washer can perform a myriad of tasks around the house and in the garden. It e󰀨ectively
cleans a wide variety of surfaces.
Your pressure cleaner is designed to operate from a cold water supply.
It operates e󰀩ciently with water temperature between 5°C and 40°C (between 41°F and 104°F).
Your high pressure washer has been designed for outdoor use only on materials such as stone, wood and
plastics. Please check, before use, whether materials can be cleaned with your sprayer; the manufacturer
cannot be held responsible for any damage resulting from improper use.
The main applications of this product are household cleaning tasks such as:
• Cars, motorcycles, bicycles
• Patios, fences, garden walls, pathways, garages and facades of houses
• To remove algae and mosses from roofs, brick walls and gutters
• For cleaning of gardening tools and machinery, furniture and grills
• For hygiene and maintenance of kennels, stables, etc. and their surroundings
It is especially useful for cleaning muddy sidings.
The sprayer alone is capable of performing most of the garden cleaning tasks or on buildings. The detergent
is useful for cleaning vehicles and other painted surfaces.
3. SYMBOLS
The labels on your tools and manual may show symbols. These represent important information about the
product or instruction on its use.
Indicates a potential personal injury hazard.
In accordance with European directives applicable to this product.
Double-insulated construction.
To reduce the risk of injury, user must read and understand owner’s manual
before using this product.
Always wear safety goggles or safety glasses with side shields and, as necessary,
a full face shield when operating this product.
Warning! Never point the gun at humans, animals, the machine body, power
supply or any electric appliances.
Machine not intended to be connected to the potable water mains.

12
Waste electrical products should not be disposed of with household waste,
please recycle where facilities exist. Check with your local authority or retailer for
recycling advice.
Recycle unwanted materials instead of disposing of them as waste. All tools,
hoses and packaging should be sorted, taken to the local recycling centre and
disposed of in an environmentally safe way.
3.1 SERVICING OF A DOUBLE-INSULATED APPLIANCE
In a double-insulated product, two systems of insulation are provided instead of grounding. No means of
grounding is provided on a double-insulated product, nor should a means for grounding be added to the
product. Servicing a double-insulated product requires extreme care and knowledge of the system, and
should be done only by qualied service personnel. Replacement parts for a double-insulated product must
be identical to the parts they replace. A double-insulated product is marked with the words “DOUBLE
INSULATION” or “DOUBLE INSULATED”. This symbol may also be marked on the product.

13
4. ASSEMBLY INSTRUCTIONS
4.1 UNPACKING THE CARTON
After opening the carton, please remove all parts and check them against the following list of components
that are included:
1. High pressure hose 5. Water inlet connector 9. Accessories holder
2. Gun holder 6. Power cable hook 10. Gun
3. Power washer unit 7. Handle 11. Adjustable nozzle
4. Cleaning pin 8. High pressure hose hook
Models:
EZN1800
EZN1800-UK
Models:
EZN2000
EZN2000-UK

14
1. High pressure hose 6. Power cable hook 12. Hose reel handle
2. Gun holder 7. Handle 13. Hose reel
3. Power washer unit 9. Accessories holder 14. Hose support
4. Cleaning pin 10. Gun 15. Pressure hose clip
5. Water inlet connector 11. Adjustable nozzle
Due to transportation and packaging, some of the accessories may be supplied disassembled. Please follow
the assembly instructions.
Always transport the machine by the handle.
Models:
EZN2200
EZN2200-UK

15
STEP 1
Screw the accessories holder tight to the main body.(Fig.1).
Screw the high pressure hose hook tight to the handle, then screw the handle tight to the main body (for
model EZN1800/EZN1800-UK/EZN2000/EZN2000-UK). (Fig.2A & 2B)
Install the two supports of the hose on the hose reel, and then install the handle to the hose reel. Then install
the hose reel on the handle of the machine. Finally install the handle on the machine body and screw it in
place (for EZN2200 / EZN2200-UK models). (Fig.2-B)
Install gun holder and power cord hook. (Fig.3)
Fig.1 Fig.3
Models:
EZN1800/EZN1800-UK
EZN2000/EZN2000-UK
Fig.2A

16
STEP 2
Attach the high pressure hose to the pressure cleaner water outlet. Insert and quick-connect it tight to avoid
leakage. When the pieces are joined properly, you cannot separate the two components by pulling straight
out from the water outlet. Push the “Button” according to the direction of arrow, then you can pull out the high
pressure hose. (Fig.4)
STEP 3
Attach the high pressure hose to the gun. Insert and quick-connect it tight to avoid leakage. When the pieces
are joined properly, you cannot separate the two components by pulling straight out from the gun. Push the
hose lock button, then you can pull out high pressure hose. (Fig.5)
Models:
EZN2200/EZN2200-UK
Fig.2B
Fig.4 Fig.5

17
STEP 4
Attach the hose connector to pressure washer. Before attaching the connector to the male tting, remove the
plastic cap, which is inserted onto the male tting on the pressure washer before shipping. This plastic cap
can be discarded once removed. After both components have been installed, attach the garden hose with
connector screw on the pressure washer. Connect the garden hose to the water supply.
WARNING!
Ensure water inlet hose is not damaged or leaking, the inner diameter of the hose must not be less than 1/2
inch and the length of the hose must not be longer than 8 metres.
STEP 5 - INSTALLATION OF THE ACCESSORIES
Install the correct accessories following below operations
Adjustable spray nozzle
Insert the adjustable spray nozzle into the gun. Push and turn the adjustable nozzle anticlockwise onto the
gun and turn it anticlockwise to lock it in place.
To remove the adjustable spray nozzle, turn it clockwise and remove it from the gun.
Models:
EZN1800
EZN1800-UK
Models:
EZN2000/EZN2000-UK
EZN2200/EZN2200-UK

18
Surface cleaner
• Screw the extension tube to the surface cleaner.
• Insert the additional tube on the gun and then
turn it anticlockwise to lock it in place.
• To remove the accessory, push the extension
tube and turn it clockwise to remove it.
• Unscrew the additional tube from the
surface cleaner to remove it.
Fix brush
Correctly align the brush with the gun.
Push the brush inside the gun. Turn
it anticlockwise to lock it in place.
To remove it, push the accessory back,
turn it clockwise, and then remove it.
Rotating brush (Only for EZN2200 and EZN2200-UK)
Correctly align the rotating brush with
the gun. Push the brush inside the gun.
Turn it anticlockwise to lock it in place.
To remove it, push the accessory back,
turn it clockwise, and then remove it.
Extension gun
Correctly align the extension gun with the gun. Push the extension gun inside the gun. Turn it anticlockwise
to lock it in place. To remove it, push the accessory back, turn it clockwise, and then remove it.

19
5. OPERATING INSTRUCTIONS
WARNING!
This unit is intended to be used with cold water only! Do not use hot water in this pressure cleaner!
High pressure hose must not loop.
WARNING!
During operation the appliance must be positioned on a rm and stable surface.
5.1 STARTING UP
WARNING!
ALWAYS turn o󰀨 the unit’s motor BEFORE turning o󰀨 the unit’s water supply.
Serious damage could occur to the motor if the unit is run without water.
a) Turn on the water supply tap fully.
b) Unlock trigger (by pressing the safety button rst
and then actuate the trigger) for a few seconds; let
the water ow out from the nozzle.
c) Check if water leaks from joints. If water leaks,
please reconnect the water hose, the spray gun or
the lance to make sure each accessory is connected
perfectly.
d) Connect to power supply.
e) Set the power switch at the position «I».(Fig.6)
f) Actuate the trigger and start the washer.
WARNING!
Check that the supply voltage and frequency correspond to those specied on the appliance data plate. The
appliance should only be connected to a mains power supply via a security breaker (Max.30mA) to cut o󰀨 the
electricity supply in the instance of a short circuit.
5.2 STOPPING THE WASHER
WARNING!
ALWAYS turn o󰀨 the unit’s motor BEFORE turning o󰀨 the unit’s water supply.
Serious damage could occur to the motor if the unit is run without water.
a) Release the trigger, the motor will stop operation.
b) Set the switch at the position «O».(Fig.6)
c) Disconnect the plug from the socket.
WARNING!
Failure to follow the above instructions may cause damage to the machine.
Fig.6

20
5.3 CHANGING ACCESSORIES
a) Release the trigger.
b) Turn o󰀨 the power switch (the position «O»).(Fig.6)
c) Disassemble the accessory and assemble the other one (see “4. ASSEMBLY INSTRUCTIONS - Step 5”).
WARNING!
Never disconnect the high-pressure discharge hose from the machine while the system is still pressurized .
To depressurize the unit, turn o󰀨 the motor, turn o󰀨 the water supply and squeeze the trigger 2-3 times.
6. INFORMATION FOR USAGE
6.1 SAFETY VALVE AND/OR PRESSURE LIMITING VALVE
WARNING!
Do not tamper with or adjust the safety valve setting.
The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens, the
pressure switch activates and the machine automatically shuts down.
If the gun nozzle is blocked, it will cause the machine pressure to rise, the safety valve to open, it will activate
the pressure switch and the machine will automatically shut down. You can refer to the following point 7 and
use a needle to clean the nozzle.
6.2. AUTOMATIC ON/OFF
The pressure cleaner is equipped with an automatic on/o󰀨 switch. The pressure cleaner will only run when
the power switch is in the ON position and the trigger on the gun is squeezed. When you release the trigger
to stop spraying water through the gun, the motor on the pressure cleaner will automatically shut o󰀨. Simply
squeeze the trigger again to resume using the cleaner. To stop using the pressure cleaner, release the trigger
and switch the unit to the OFF position. The unit should be turned completely OFF while not in use or while
unattended.
6.3. BLEEDING THE GUN
It is very important to bleed the gun before using the pressure cleaner. Refer to the “Assembly Instructions”
to assemble the pressure cleaner. To bleed the gun, simply connect the garden hose to the pressure cleaner
and squeeze the trigger BEFORE turning the electrical supply on. This allows any air trapped inside the
pressure cleaner and gun to be removed before using the unit. Continue holding trigger for approximately
one minute to allow any excess air out of the unit. Water will ow through the gun at low pressure during this
procedure. For more bleeding tips, see the section titled “Operating Instructions.”
6.4 GUN SAFETY LOCK
This pressure cleaner is equipped with a gun trigger safety
lock. When not using the pressure cleaner, use the safety
lock to keep from accidentally engaging the high pressure
spray (Fig.7).
Lock Unlock
Fig.7