ENFORCER Elite EV-2606-NJEQ User manual

ENFORCER Vandal-Resistant CCD Dome Camera Manual ENFORCER Vandal-Resistant CCD Dome Camera Manual
ENFORCER
VIDEO
®
• CheckthattheCCTVcameraispoweredup.
• Checkthatthemonitorispoweredup.
• Checkthatthevideocableconnectingthe camera tothemonitoris connected properly.
• Cleanthelens (using a soft, clean cloth).
• Checkthat the light sourceisadequate.
• Cleanthe dome.
• Ifthebacklightcontrol(BLC)DIPswitch is set to OFF,trysettingittoON.
• Checkthat the automaticelectronicshutter (AES) DIPswitch is turned OFF.
• Adjustthemonitor’scontrastknob.
• Changethe position of the camera.
• Ifmultiple cameras are used,makesurethe polarity ofthepowerconnections is consistent.
• (24VAC only) If more than one camera is attached to the same power source, adjust the
othercamera’slinelock sync. Thiscameracannot beadjusted.
• Changethepositionofthecamera.
• Checkthatthecorrectpowersupply is in use.
The screen is blank
The screen image is dim
The screen image is dark
The screen image has poor contrast
The screen image flickers
The screen image rolls
The screen image is distorted
The camera case is hot
TROUBLESHOOTING
Flush or
Surface
Mount
With 36 LEDs
WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a
dangerous electric shock, damage the device, and void the warranty. Do not open the case of this device, as there are
no field-serviceable components inside.
FCC COMPLIANCE STATEMENT: Information to the user: This equipment has been tested and found to
comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However,
the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the
right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2008 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.
WARRANTY: All SECO-LARM products are warranted against defects in material and workmanship while used in
normal service for a period of two (2) years from the date of sale to the original consumer customer. Our obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
For complete details regarding the SECO-LARM warranty, please contact SECO-LARM.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
Vandal-Resistant Dome Cameras
MANUAL
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®®
®®
®
file: VandalDomes0508_IMUa.pmd
SECO-LARM®U.S.A., Inc.
16842MillikanAvenue,Irvine,CA 92606
Tel:[phone] Fax: [phone]
Website:www.seco-larm.com
E-mail:sales
@ seco-larm.com
PIKPR1
®
8
EV-2605-NKEQEV-2606-NJEQ
The Series

ENFORCER Vandal-Resistant CCD Dome Camera Manual ENFORCER Vandal-Resistant CCD Dome Camera Manual
TABLE OF CONTENTS
FEATURES
· Sony 1/3” Super HAD CCD.
· ICRmechanicalday/night .
· Varifocal aspherical DCAuto iris, F1.2 lens.
· Color and B/W auto switching by photocell.
· DIPswitch control for day/night time delay,
flickerless, BLC, and white balance.
· DC iris control level volume built-in.
Introduction ............................................... 2
Features .................................................... 2
OptionalAccessories ................................. 2
Specifications ............................................ 3
Dimensions ............................................... 3
CameraAssembly ..................................... 4
Before Starting .......................................... 4
Mounting Instructions (Surface or Flush)... 5
3-Axis GimbalAdjustment ......................... 6
Zoom and FocusAdjustment..................... 6
DIP Switch and DC IrisAdjustment ........... 7
Camera Connections................................. 7
Troubleshooting......................................... 8
Warranty.................................................... 8
Model EV-2606-NJEQ EV-2605-NKEQ
INTRODUCTION
TheEliteSeriesVandalDomecamerasaretheidealsolutions to manydifferentCCTV
challenges.Thecamerafeaturehi-resolution,ICRmechanicalday/night,andavarifocal
lenstoensureaprecise,clearimageinanylightingcondition.Heavy-duty,vandal-proof
materialscombinedwithanIP66weatherproofrating makethiscamerasuitableforusein
nearlyanycondition.
OPTIONALACCESSORIES
DIMENSIONS
· Easy adjustment of focal length and focus.
· True 3-axis gimbal bracket (2-pan, 1-tilt).
· Service monitor port.
· Vandal-resistant and weatherproof housing
(IP66).
· 24VAC/12VDC dual power source.
Wall Mount Bracket
EV-2605WM
Ceiling Mount Bracket
EV-2605CM
32
43/16” (70mm)
41/4”
(108mm)
113/16”
(46mm)
39/32” (83mm)
41/4”
(108mm)
39/32”
(83mm)
43/16” (70mm)
113/16”(46mm)
511/16”(145mm)
415/32”(113.5mm)
41/16”
(103mm)
11/4”
(32mm)
13/16”
(20mm)
2”
(51mm)
43/16”
(107mm) 2”
(51mm)
Type
Image sensor
Resolution
Pickup elements
Sync
Video output
Shutter speed
Iris control
Gain control
Gammacorrection
White balance
Backlight compensation
S/N ratio
Powersource(+/-10%)
Ambienttemperature
Varifocal lens
Minimum illumination
Power consumption @ 24VAC
Power consumption @ 12VDC
Weight
Color IR Vandal-Resistant Dome Color Vandal-Resistant Dome
1/3" interline transfer for color CCD (Sony)
550 TV lines
768 x 494 pixels
Internal
1 Vp-p composite output, 75 Ohms.
1/60 sec.
DC auto iris
Auto
0.45
ATW /AWC selectable
ON/OFF selectable
> 48dB (AGC off)
24VAC or 12VDC
14o~ 122oF (-10o~50oC)
3.8~9.5 mm 2.8~11.0 mm
0 lux IR LEDs on 0.03 lux / F1.2
Max:12VA Max. 4.8VA
Max:650mA Max. 250mA
4 lbs. 6 oz. (2.0 kg) 4 lbs. 6 oz. (2.0 kg)
SPECIFICATIONS

ENFORCER Vandal-Resistant CCD Dome Camera Manual ENFORCER Vandal-Resistant CCD Dome Camera Manual
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera where it is exposed to rain or other moisture, or in humid or dusty places.
4. Do not point the CCTV camera at the sun. Heat could damage the camera, even when not in use.
5. Do not mount the CCTV camera in areas exposed to radiation, strong magnetic fields, or strong
electrical signals.*
6. Do not drop the camera or subject it to strong vibrations.
* NOTE: Many video monitors produce strong electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during de-Gaussing, which occurs
automatically with many monitors when the monitor is turned on.
54
MOUNTING INSTRUCTIONS
1. Remove the dome cover by loosening 3 security screws with
supplied Torx wrench.
2. Mount the camera to ceiling or wall.
A. If surface mounting, see figure 1.
B. If flush mounting, see figure 2.
C.If mounting to electrical box, see figure 3 and 4.
Figure 1 - Surface Mount Figure 2 - Flush Mount
A. Use Guide Pattern on wall or ceiling.
B. Using four ST4x30 screws, mount surface base
to a sturdy surface.
C.Using four M4x10 screws, affix flush mount
base to surface base.
A. Use Guide Pattern on wall or ceiling.
B. Using four ST4x30 screws, affix flush mount
base to a sturdy surface.
Plastic
anchors
(if needed)
ST4x30
MX4x10
Torx M4x9
Lens
Power input connector
12VDC/24VAC dual voltage
Video output
connector - BNC
Service monitor
port
Surface mount base
Mounting screws
(Phillips ST4x30)
Flush mount base
Assembly screws
Dome cover ring Safety strap
Assembly screw
(Torx M4x9)
Domecover
Camera control board
Alignment mark
Back conduit plug (1”)
Side conduit plug (1”)
UNC8-32x0.75
(not included)
1”electrical
conduit
UNC8-32x0.75
(not included)
ST4x30
(Phillips M4x10)
Figure 3 - Mounting to Electrical Junction Box
(with surface mount base)
CAMERA ASSEMBLY
Figure 4 - Mounting to Electrical Junction Box
(flush mount)

ENFORCER Vandal-Resistant CCD Dome Camera Manual ENFORCER Vandal-Resistant CCD Dome Camera Manual
EVT-PB1Q
- Transmit video over UTP Cat5 cable.
- Up to 2,000 (610m).
CA-1610-3FLQ
- Illuminated pigtail connector.
- Patent pending.
6
DIP SWITCH ADJUSTMENTS AND DC IRIS ADJUSTMENT
DIP
switches
DC level
adjustment
Service
monitor
port
DIP switch settings
(default settings shown)
1 2 3 4
3-AXIS GIMBAL ADJUSTMENT
ON / OFF
1. Make any necessary adjustments to the horizontal and vertical angles of the camera itself while checking
the image in the video monitor.
2. Pull the zoom lever out and loosen it by turning it counter-clockwise. Slide the lever right or left depending
on how close the camera is to the protected area. After adjustments have been made, turn the lever
clockwise to tighten it, then push the lever back in.
3. Pull the focus lever out and loosen it by turning it counter-clockwise. Slide the lever right or left to bring the
protected area into focus.After adjustments have been made, turn the lever clockwise to tighten it, then
push the lever back in.
CAMERA CONNECTIONS
OPower: 12VDC or 24VAC.
OUse the supplied service monitor adapter to connect to service monitor.
ZOOM AND FOCUS ADJUSTMENT
The 3-axis gimbal allows the camera to rotate 360° horizontally, 360° vertically and 60° tilt.Adjust the proper
angle as needed.
Axis-3
360°
Axis-3
screw
Axis-1
360°
Axis-2 Tilt
60°
12VDC/24VAC
(non-polarized)
Service monitor
output adapter CCTV monitor
Service monitor
Zoom
adjustment
Focus
adjustment
#
1
2
3
4
ICR Switch Time1
Flickerless2
Back Light
Compensation (BLC)3
ATW4 or AWC5
2 sec
Flickerless Off
BLC On
ATW
Feature On (Default) 4 sec
Flickerless On
BLC Off
AWC
Off
DIP Switch Functions
1 IR Cut Filter Removable (ICR) Switching Time
The timing delay before switch from color and B/W mode.
2 Flickerless
Stabilize the image during rapid changes in different lighting conditions.
3 Back Light Compensation (BLC)
keeps the foreground image properly illuminated where a strong backlight is present.
4 Auto Tracking White Balance (ATW)
Adjusts white balance automatically as brightness changes. (Color temperature 2,500K~9,500K)
5 Auto White Control (AWC)
White balance is fixed. In theAWC mode, white objects must cover more than half of the image field in order
for AWC to function properly. (Color temperature 2,000K~18,000K)
Light
Dark
Iris level DC level
adjustment
1. Axis-1: Turn axis-1 by hand for up to 360
degrees rotation.
2. Axis-2: Adjust axis-2 (tilt) up or down by hand.
3. Axis-3: Loosen the axis-3 screw to adjust the
3rd axis to the desired angle and then
tighten the screw.
ALSO AVAILABLE
FROM SECO-LARM
7
7.5”
IMPORTANT: Make sure the focus and zoom levers are pushed back in after
adjustments are made. Failure to do so may cause damage to the dome.
Telephoto (T)
Wide(W)
Far ( )
Near(N)
8
Zoom
Focus